INSTALLATION METHOD
This is an anti-theft installation method.
The main unit wears a METAL SLIDE BRACKET HOUSING.
Please connect the wiring such as power supply, speakers and antenna
according to the requirements of this operation manual, then install the
metal slide housing into the car according to the following diagram.
To boost up the capability of anti-jamming,
please make sure fix tightly the support metal
strap into the metal joint that connect to the
SUPPORT METAL STRAP
HEX NUT
SPRING WASHER
PLAIN WASHER
PLAIN WASHER
TAPPING SCREW
DASHBOARD
METAL SLIDE BRACKET HOUSING
To draw the CHASSIS out of the METAL SLIDE BRACKET
HOUSING, insert the two KEY PLATES into the left and right
side slots of the chassis at the same time, then draw out the
chassis emphatically as the right illustration.
chassis of the car.
NOTE
UNIT CHASSIS
For properly fix the metal chassis,
bend over the tabs according to
the high of the DASHBOARD.
PLASTIC TRIM OUT
FRONT PANEL
LEGACY
INSTRUCTION MANUAL
Remove the METAL SLIDE
BRACKET HOUSING as arrow
illustration
Please make sure remove the two screws
for protect the CD DECK MECHANISM during
transportation before operating.
To mount the panel, insert right side of the panel
into right side of the chassis first, then push the
left side of the panel into the chassis until a click
sound is heard.
ANTI-THEFT DETACHABLE SYSTEM
AUTO-LOADING COMPACT DISC PLAYER
WITH AM/FM STEREO MANUAL TUNING RADIO
MODEL:LCD15DX
LOCATION AND FUNCTION OF CONTROLS
WIRING DIAGRAM
ANTENNA PLUG
1. RELEASE BUTTON
Press this button to release the front panel when you want to take it away for
safekeeping.
2. TUNING CONTROL
Rotate this control at radio mode to select your desired radio broadcasting
station. And the frequency which has been selected will appear on the display.
3.4. SEL( AUDIO MODE SELECT)/VOLUME V.+/V.- BUTTON
Press SEL button to change the mode in sequence as follows:
VOL BAS TRE BAL FAD VOL
a. The volume can be adjusted at any time by pressing the audio level V.+ or
V.- button as select mode has been initially defaulted at volume mode.
b. The volume can be also obtained by stepping through the SEL button, after
the character VOL appeared on the LCD display, press V.+ or V.- button
to adjust the volume.
c. Press and hold the V.+ or V.- button to direct adjust the volume.
BASS CONTROL (WITHOUT APPLY EQ)
a. Press SEL button to select the bass mode until BAS appears on the display.
b. Press V.+ or V.- to adjust the bass effect.
TREBLE CONTROL (WITHOUT APPLY EQ)
a. Press SEL button to select the treble mode until TRE appears on the display.
c. Press V.+ or V.- to adjust the treble effect.
MEMORY B+
BLACK(GND)
ACC RED (B+)
BLUE AUTO ANT
FRONT
LEFT
SP
REAR
YELLOW
+
-
+
-
7 A
FUSE
0.5 A
FUSE
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK VIOLET/BLACK
RCA LINE OUT
GREY
GREY/BLACK
VIOLET
RED R
WHITE L
+
-
+
-
FRONT
RIGHT
SP
REAR
Note:
1.Make sure use a speaker with 4 ohm load impedance to reduce
the distortion during high volume level.
2.Do not make the auto antenna wire and ground touch each other.
SPECIFICATION
GENERAL
Power requirement.................................................................................................DC 12V.
Current consumption..............................................................................................7A MAX.
POWER OUTPUT.....................................................................................................4 X 7W.
FM SECTION
Frequency range........................................................................................88MHz -108MHz.
Usable sensitivity.........................................................................................................10uV.
I.F Frequency........................................................................................................10.7MHz.
AM SECTION
Frequency range.....................................................................................530KHz - 1700KHz.
LINE - OUT [OPTION]
Output................................................................................250mV @ FM 10% THD POWER.
Impedance............................................................................................................600 ohm.
CD PLAYER
System........................................................................................compact disc audio system.
Usable disc......................................................................................................compact disc.
Signal format.............................................................................sampling frequency 44.1KHz.
No of quantization bits 1bit.
Frequency characteristics...............................................................................5-40Hz < 5dB
10K-20KHz < 5dB.
Signal to noise radio................................................................70dB [1KHz] [IEC - A net work].
Chassis dimensions...................................................................183[W] X 53[H] X 160[D]mm.
1
6
TROUBLE SHOOTING
To solve the common problems, refer to the Trouble Shooting List.
If you still cannot solve the problem, consult your nearest service
dealer.
Symptom
No power
Disc cannot
be loaded or
ejected
No sound
Sound skips
The radio does
not work
The antenna cable is not
connected
the signals are too weak
Cause
The car ignition is not on. If the power supply is properly
The fuse is blown
Presence of CD disc inside
the player
Inserting the disc in upside
down
Compact disc is extremely
dirty or defective
Temperature inside the
car is too high
Condensation
Volume is in minimum
Wiring is not properly
connected
The installation angle
is more than 30 degrees
The disc is extremely
dirty or defective
connected to the car accessory
switch the ignition key to " ACC "
Replace the fuse
Remove the disc in the player
then put a new upward
Insert the compact disc with
the label facing upward
Clean the disc or try to play a
new one
Cool off until the ambient
temperature returns to normal
Leave the player off for an
hour or so, then try again
Adjust volume to a desired level
Check wiring connection
Adjust the installation angle
to less than 30 degrees
Clean the compact disc/try to
play a new one
Insert the antenna cable firmly.
Solution
BALANCE CONTROL
a. Press SEL button to select the balance mode until BAL appears on the display.
b. Press V.+ button or V.- button to adjust the audio output effect of left and
right speaker.
FADER CONTROL
a. Press SEL button to select the balance mode until FAD appears on the display.
b. Press V.+ button or V.- button to adjust the audio output effect of front and
rear speaker.
5. LCD - LIQUID CRYSTAL DISPLAY
6. POWER BUTTON
Press this button to turn the power supply on or off.
7. EJECT KEY
Press this key to eject the CD DISC from the disc compartment.
8. TRACK UP/DOWN BUTTONS
During CD mode, press button to advance to previous track backwards.
Hold the button to fast reverse the CD program. Release to resume CD
playback.
During CD mode, press button to advance to next track forwards.
Hold the button to fast forward the CD program. Release to resume CD
playback.
9. LOC/RPT BUTTON
LOCAL/DISTANT MODE:(This operation is effective on FM reception only.)
At RADIO mode, press this button to switch between local and distant
reception. And the character LOC will appear on the LCD display indicating
reception locally.
Press LOC to improve local reception in some areas where the signal is too
strong. Press LOC to improve distant reception when you are located at a
weak signal location.
REPEAT MODE:
At CD mode, press this button to continuously repeat the same track.
Press again to stop repeat.
10. LUD/RDM BUTTON
LUD MODE:
Press this button to enhance the bass output effect while reduce the volume.
Press again to cancel loudness effect.
RDM MODE:
During CD mode, press RDM button and hold for 2 seconds to enter random
playback mode, the RDM will appear on LCD, then press or to play all
track on the current disc in random order, press RDM button and hold for 2
seconds again to exit this mode.
5
2
11. MO/INT BUTTON
MO/ST MODE:(This operation is effective on FM reception only.)
During radio mode, press this button to change between mono and stereo
modes. And he character ST will appear on the LCD display while there is a
strong signal from an FM station that is broadcasting in stereo.
Mono improves the reception of the distant stereo FM stations.
INT MODE:
During CD mode, press this button to play the first 10 seconds of each track
on the disc. Press again to exit INT mode and resume CD playback when your
desired track appear.
12. EQ BUTTON
Press this button to switch between 3 preset equalizer curves: POP, CLAS,
ROCK. The audio output effect will be corresponding changed.
PRECAUTION OF DISC PLAY:
Cleaning discs
Before playing, clean the disc with a clean, lint-free.
Wipe the disc in the direction of the arrow.
13. BAND BUTTON
During CD playback, press this button once to switch to RADIO mode.
Then press this button for AM or FM reception.
And the character of corresponding band will be visible on the display.
14. CD ( CD PLAY, PAUSE) BUTTON
At RADIO mode, press button to switch to CD mode.
At CD mode, press this button to suspend the CD playback and press again
to resume normal CD playback.
15. CLOCK DISPLAY AND SETTING BUTTON
During CD or RADIO mode, press CLK button once to display the real time.
With time appeared on the display, Press and hold CLK button for more than 2
seconds, until time flashes. and you can adjust HOUR and MINUTE by pressing
button and button repeatedly.
16. MUTE BUTTON
Press this button to suppress the audio output 100% immediately, press again
to resume normal audio output.
IMPORTANT:
MEMORY WIRE ( FOR BACKUP) AND POWER WIRE CAN NOT BE SWITCHED
OFF AT THE SAME TIME, ONCE IT HAPPENS, ALL THE FUNCTION WILL BE
TOTALLY IN DISORDER (DISTORTED DISPLAY IS ALSO INDICATED ).
PLEASE FOLLOW THE INSTRUCTIONS AS MENTIONED
IF IT REALLY HAPPENS,
BELOW:
5 MINUTES LATER,
PLEASE SWITCH ON THE MEMORY WIRE FIRST (CAN NOT
PASS THROUGH IGNITION SWITCH) AND THEN SWITCH ON THE POWER. IT WILL
RETURN TO NORMAL FUNCTION SOON.
NOTE:
Do not use so solvents such as benzine, thinners. Commercially available
cleaners or anti static spray damage the unit.
Do not insert a disc with the label surface down. Or may damage the unit.
Label
surface up
NOTE:
Do not try to insert another disc when one has been already inserted.
Doing so may damage the unit.
Handle the disc by its edge. And to keep the disc clean, do not touch
the surface.
Do not stick paper or tape on the disc.
Do not expose the disc to direct sunlight or heat sources such as hot air
ducts. Or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
3
4
Loading...