Legacy Car Audio Car CD Player User Manual
OWNER’S MANUAL
MANUALLY TUNED SYNTHESIZER STEREO RADIO
WITH COMPACT DISC PLAYER DIGITAL
CONTENTS
Installation .....................................................................................................3
DIN Front-Mount (Method A) ..................................................................................3
Installing the unit ...............................................................................................3
Removing the unit .............................................................................................4
DIN Rear-Mount (Method B)...................................................................................4
How To Remove And Install The Front Panel (Optional) ...........................5
Wiring Connection ........................................................................................6
2 X 7W System .......................................................................................................6
4 X 7W or 2 X 25W System.....................................................................................6
Operation .......................................................................................................7
Radio Operation ..........................................................................................10
CD Operation...............................................................................................11
Specification................................................................................................12
Trouble Shooting .........................................................................................13
2
INSTALLATION
Notes:
• Choose the mounting location where the unit will not interfere with the normal driving
function of the driver.
• Before finally installing the unit, connect the wiring temporarily and make sure it is
all connected up properly and the unit and the system work properly.
• Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
• Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
• Install the unit where it does not get in the driver’s way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
• If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum
performance.
30˚
• Avoid installing the unit where it would be subject to high temperature, such as from
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,
dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from “Front” (conventional DIN Front-mount)
or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of
the unit chassis). For details, refer to the following illustrated installation methods.
DIN FRONT-MOUNT (Method A)
Installing the unit
1
182
53
(Fig. 1)
2
3
1. Dashboard
2. Holder
3. Screw
3
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
1
7
4
2
3
(Fig. 2)
Removing the unit
1
3
1. Dashboard
6
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
7. Plain washer
1. Frame
2. Insert fingers into the groove in the front
of frame and pull out to remove the frame.
(When re-attaching the frame, point the
2
side with a groove downwards and attach
it.)
3. Lever
Insert the levers supplied with the unit
into the grooves at both sides of the unit
as shown in figure until they click. Pulling
the levers makes it possible to remove
the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the sides of the unit.
1
5
3
2
5
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw holes
of the bracket and the screw holes of the
2
main unit become aligned (are fitted), and
tighten the screws at 2 places on each
side.
4
Use either truss screws (5 x 5mm) or
flush surface screws (4 x 5mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method B
installation.
4
Loading...