Installation and Operating Manual
Model(s): Magnafire Series Coal Stoves Mark I, Mark II and Mark III
NOTICE: SAVE THESE INSTRUCTIONS
Report Number: 0536CS002S
Certified To: UL 1482-2011, ULC S627-00
Legacy Stoves, A Division of:
Alternate Heating Systems
2393 Little Egypt Rd
Harrisonville, PA 17228
WARNING: HOT
SURFACES!
Glass and other surfaces are hot during operation and cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as stove.
• Alert children and adults to hazards of high temperatures.
• High temperatures may ignite clothing or other flammable materials. Keep clothing, furniture,
draperies and other flammable materials away.
⚠SAFETY NOTICE - CAUTION!
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL OR USE YOUR NEW ROOM HEATER.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN
DEATH.
APPROVED FOR USE IN THE U.S. AND CANADA
IF THIS LEGACY STOVES PRODUCT IS NOT INSTALLED CORRECTLY, A HOUSE FIRE MAY RESULT.
FOR YOUR SAFETY, FOLLOW INSTALLATION DIRECTIONS PRECISELY. CONTACT LOCAL BUILDING OR FIRE
OFFICIALS ABOUT RESTRICTIONS AND INSPECTION REQUIREMENTS FOR YOUR AREA. CONTACT YOUR
LOCAL AUTHORITY (SUCH AS THE MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT, FIRE
PREVENTION BUREAU, ETC.) TO DETERMINE THE NEED FOR A PERMIT. DO NOT INSTALL IN A MOBILE HOME
CETTE GUIDE D’UTILISATION EST DISPONIBLE EN FRANCAIS. CHEZ VOTRE CONCESSIONNAIRE DE LEGACY
STOVES HOME HEATING.
Introduction
Thank you for purchasing a Legacy StovesTM Magnafire coal stove. The Magnafire series has been designed and built to last. Whether
you’re heating a room or heating your whole house, you’ve made the right choice. Please read this entire instruction manual before
attempting to install or operate your new stove. If you have further questions regarding your new stove, contact your Legacy StovesTM
dealer. Follow these instructions and you will have many years of warmth and comfort enjoying your new coal stove.
If you are a first-time coal burner, keep in mind that you will not have instant success with maintaining a fire. No one does. Following
these instructions should help you with the basic principals.
Please copy your serial number, from the label on the back of your stove, to the box below.
-4-
Legacy StovesTM Mark Series Stove Label measures: 9.5" high X 8.5" wide
-5-
Table of Contents
⚠SAFETY NOTICE - CAUTION!................................................................................................................1
Introduction....................................................................................................................................................4
Additional Warnings and Notices...................................................................................................................7
Installation......................................................................................................................................................8
1. Safety Considerations............................................................................................................................8
1.1 KEEP CHILDREN AWAY-MAY CAUSE SERIOUS BURNS......................................................8
1.2 FUEL / FIRING INFORMATION..................................................................................................8
1.3 CURING PAINT.............................................................................................................................8
1.4 MOBILE HOMES..........................................................................................................................8
2. Assembly& Installation.........................................................................................................................8
2.1 UNPACKING AND INSPECTION OF PARTS.............................................................................8
2.2 LOCATING THE STOVE..............................................................................................................8
2.3 FLOOR PROTECTION..................................................................................................................8
2.4 ASSEMBLY....................................................................................................................................9
2.5 general information – installation checklist....................................................................................9
Venting..........................................................................................................................................................10
3. Venting and Chimneys.........................................................................................................................10
3.1 Types of Chimneys........................................................................................................................10
3.2 COMMON CHIMNEY PROBLEMS...........................................................................................10
3.3 What to do if you have a problem.................................................................................................11
3.4 Magnafire Chimney Specifics.......................................................................................................11
4. Grates..................................................................................................................................................14
4.1 Grate system and controls.............................................................................................................14
Operation......................................................................................................................................................15
5. Operating Instructions.........................................................................................................................15
5.1 Starting a Fireplace.......................................................................................................................15
5.2 Blower Operation..........................................................................................................................15
5.3 Loading.........................................................................................................................................15
5.4 Increasing Heat from a Low Fire..................................................................................................15
5.5 Shaking Ashes...............................................................................................................................15
5.6 Ashes and Their Removal.............................................................................................................15
5.7 Safety............................................................................................................................................16
5.8 Controlled Firing...........................................................................................................................16
6. Maintenance.........................................................................................................................................16
6.1 Periodic and Everyday Maintenance.............................................................................................16
6.2 Coal/Fuel Handling and Storage...................................................................................................17
6.3 Glass Doors – Maintenance..........................................................................................................17
6.4 Glass Doors – Glass Replacement................................................................................................17
7. Warranty Information...........................................................................................................................19
8. Service Parts........................................................................................................................................21
Service and Maintenance Log......................................................................................................................28
Service and Maintenance Log......................................................................................................................29
-6-
Additional Warnings and Notices
This appliance is also approved for installation into a shop.
MARK I
MARK II
MARK III
CONTACT YOUR LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA
BARCODE LABEL
PREVENT HOUSE FIRES:
Install and use only in accordance with manufacturer’s installation and operation instructions and local building codes. In absence of
any local codes, installation must meet minimum requirements of NFPA 211 in USA. Refer to manufacturer’s instructions and local
codes for precautions required for passing chimney through a combustible wall or ceiling. Inspect and clean chimney system frequently
in accordance with manufacturer’s instructions.
FOR USE WITH COAL ONLY.
Don’t connect this stove to a chimney serving another appliance.
Flue connector pipe must be 6” diameter, minimum 24 MSG black or 26 MSG blue steel.
Chimney must be factory built 103HT or masonry.
NOTE: Replace glass only with 5mm ceramic glass available from your dealer.
Inspect and clean chimney frequently. Under certain conditions of use, creosote buildup may occur rapidly.
CAUTION! STOVE IS HOT WHILE IN OPERATION.
KEEP COMBUSTIBLES SUCH AS FURNITURE, FUEL,
AND DRAPERIES AT LEAST 36 INCHES AWAY FROM
THE APPLIANCE.
DO NOT LEAVE SMALL CHILDREN UNATTENDED
WHILE IN THE ROOM WITH THIS HEATER.
ALWAYS WEAR GLOVES WHEN ATTENDING TO THE
STOVE.
THIS STOVE IS NOT AN INCINERATOR. DO NOT
BURN GARBAGE, PAINTED OR TREATED WOOD.
NEVER USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR “FRESHEN UP” A
FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS
WELL AWAY FROM THE HEATER WHILE IT IS IN USE.
DO NOT OVERFIRE - IF HEATER OR CHIMNEY
CONNECTOR GLOWS, YOU ARE OVERFIRING.
-7-
Installation
1. Safety Considerations
1.1 KEEP CHILDREN AWAY-MAY CAUSE SERIOUS BURNS
CAUTION: All surfaces of the stove are hot while in operation. Do not touch. Keep Children Away. Wear gloves while tending stove.
Serious burns will result if special care is not taken.
1.2 FUEL / FIRING INFORMATION
DANGER! FIRE HAZARD! DO NOT USE CHEMICALS OR FLUIDS TO START OR “FRESHEN UP” A FIRE. SEVERE BODILY
INJURY AND/OR A FIRE IN THE HOME MAY RESULT. DO NOT BURN GARBAGE, GASOLINE, THINNERS, KEROSENE, OR
FUEL OIL, ETC. AN EXPLOSION, A HOUSE FIRE OR PERSONAL INJURY COULD RESULT. KEEP ALL SUCH LIQUIDS WELL
AWAY FROM THE STOVE WHILE IN USE.
This heater is approved for burning coal only. Use of any other fuel, except for the purpose of coal ignition, is a violation of U.S. law.
When and if the chimney pipe or connector reaches 500˚ f. (maximum temperature), the stove is being overfired. It is recommended
that you use magnetic thermometers on the stove and flue connector, to ensure safe operation. This stove consumes air when it is
burning. If your house is especially tight, It is advisable that a nearby window be opened slightly while burning the stove. Information
in this manual is manufacturer’s recommendations. If there is a discrepancy between these recommendations and your local code
requirements, you must follow local codes.
1.3 CURING PAINT
During the first few hours of burning, a blue smoke will be observed rising from the painted surfaces of the stove. This is the paint
being cured, and will disappear over time. Increase the amount of fresh air in the room during this initial break-in period. This may be
achieved by opening doors or windows.
1.4 MOBILE HOMES
This stove is not approved for use in mobile homes
2. Assembly& Installation
2.1 UNPACKING AND INSPECTION OF PARTS
Inspect the stove for any visible damage. The blower and the shaker handle are packaged inside the stove.
2.2 LOCATING THE STOVE
Locate the stove as close to the chimney or flue as possible while adhering to the
recommended clearances to combustible material. Safe stove clearance to
combustible walls is 24” to the rear of the stove, and 33” to the sides of the stove. In
a corner installation, you need 24” to the side walls. Clearance to the front of the
stove, for furniture, etc. is 36”
CLEARANCE TO COMBUSTIBLE SURFACE
A - Unit to Sidewall 33” 838 mm
B - Unit to Backwall 24” 610 mm
C - Chimney Connector to Side Wall 42” 1067 mm
D - Chimney Connector to Back Wall 18” 457 mm
E - Floor Protector, Side and Rear 8” 203 mm
F - Floor Protector, Front 16” 406 mm
H - Pipe Connector to Ceiling 18”* 457 mm
*Not Tested - NFPA Guildlines
2.3 FLOOR PROTECTION
Floor protection must be of approved non-combustible material. It must be
located under the appliance and extend beyond the appliance according to
the measurements below. Floor protection must also extend under any
horizontal sections of chimney connector and 2” (50.8mm) beyond each
side of the connector.
J – Sides USA/CANADA 8” 203 mm
K – Front USA/CANADA 18” 457 mm
L – Rear USA 8” 203 mm
L – CANADA Wall Wall
-8-
2.4 ASSEMBLY
Slide the blower into the slotted bracket on the rear of the stove. The blower will rest at
the bottom of the slot.
The shaker handle bolts onto the shaker block using the bolts and lock washers provided.
The draft control is bolted through the hole in the center of the ash door as shown
below. The knob should spin freely and open to a distance of about 1/4 inch from the
door surface, while being able to close against the face of the door.
The Viewing Glass →
The viewing glass is installed between the door and the window frame. The glass
gasket is installed only on the sides of the glass panel. The top and bottom of the
glass are open to provide air-wash and secondary air to the firebox. The glass
frame is secured to the door with four bolts.
The Mark III also has a top trim piece which bolts onto the top of the door.
Be sure the frame bolts and trim bolts are secured.
2.5 GENERAL INFORMATION – INSTALLATION CHECKLIST
A) Have your stove installed by a trained installer. Preferably one who is certified by the National Fireplace Institute or similar
certification agency.
B) Before starting Installation, check for proper clearance to combustibles where the stove is going to be located.
C) Never vent a solid fuel burning appliance into a flue serving
another appliance.
D) Have the chimney inspected and thoroughly cleaned.
Inspect that it is a Class “A” chimney either masonry or
factory built. If it is a manufactured chimney, ensure that it
is installed as per the manufacturers requirements. be sure
that the chimney is tall enough. Solid fuel chimneys fall
under a general rule, 16 ft. minimum height, 2 ft. taller than
anything within 10 ft., and 3 ft. above where it passes
through the roof line. The chimney must be capable of a
minimum .06 inches of water column of draft when the
stove is burning.
E) Limit the amount of connector pipe. Position the stove as
close to the flue as possible. (8 ft. or less) No more than two
90° elbow fittings should be used. Any horizontal connector
pipe should have at least 1/4 in. of rise per foot in length. A
barometric damper may be installed to prevent excessive or
erratic draft.
(See section 2.2)
MANUAL DAMPERS OR “HEAT SAVERS” MUST NEVER BE INSTALLED IN THE FLUE PIPE. IMPROPER OPERATION COULD
RESULT IN DEATH.
-9-
Venting
Chimney connectors shall not pass through an attic or roof space, closet or similar concealed space, or a floor or ceiling. Where passage
through a wall, or partition of combustible construction is necessary, the installation shall conform to
Code for Solid-Fuel-Burning Appliances and Equipment.
Where an existing chimney is used, it must be large enough to provide a draft adequate for removing gaseous products of combustion.
From NFPA 211 2013:
1. The cross-sectional area of the chimney system must not be less than that of the flue collar. (For The Mark I and Mark III
served by a round chimney, the diameter must be at least 6 inches)
2. Chimney systems which are completely internal below the roofline must be no more than three times the crosssectional area
of the flue collar (28.3 in2 X 3 = 84.8 in2).
3. Chimney systems which are exposed to the exterior on one or more sides below the roofline must be no more than two times
the cross-sectional area of the flue collar (28.3 in2 X 2 = 56.5 in2).
3. Venting and Chimneys
3.1 TYPES OF CHIMNEYS
The chimney is one of the most important, yet the most neglected and misunderstood portion of any solid fuel burning appliance
installation. Do not connect your stove to a chimney flue that already serves another heating device.
Under no circumstances should a manual flue damper be installed in the smoke pipe between the stove and the chimney.
CAUTION! THE CHIMNEY MUST BE A “CLASS A” CHIMNEY IN GOOD WORKING CONDITION. THE USE OF
ALUMINUM “TYPE B” GAS VENT FOR SOLID FUELS IS UNSAFE, AND PROHIBITED BY THE NATIONAL FIRE
PROTECTION AGENCY (NFPA) CODE.
CAN/CSA-B365, Installation
There are three types of “Class A” chimneys:
1. Masonry with a tile liner, including brick, block, stone, etc. It must be supported by a ground-level foundation.
2. Insulated “Class A” manufactured chimney, listed and certified by a national test agency.
3. Triple-walled metal “Class A” chimney, listed and certified by a national test agency.
If your masonry chimney has not been used for some time, have it inspected by a qualified person (building inspector, fire department
personnel, etc.). If a listed and certified manufactured chimney is to be used, make certain it is installed in accordance with the
manufacturers instructions and all local codes. A coal stove can perform only as well as its venting system will allow it to.
CAUTION! THE CHIMNEY SELECTED MUST COMPLY WITH THE REQUIREMENTS FOR TYPE HT CHIMNEYS UL 103
DO NOT USE MAKE-SHIFT COMPROMISES DURING INSTALLATION!
3.2 COMMON CHIMNEY PROBLEMS
In order to have a properly operating heating system, the chimney needs to
be capable of providing sufficient draft. The minimum required draft is .06
inches of water column (WC). To measure the draft, drill a hole in the
connector pipe and attach a draft meter. First, check the draft above the
barometric damper (if installed). Then check it below the barometric
damper and make your damper adjustment to where it opens to prevent the
draft from going higher than the .06 in WC. If the chimney is incapable of
supplying the necessary draft, it will need to be improved. Whether it needs
to be raised to a taller height, a flue liner installed, or a different style of cap
placed on the top, the improvement method will need to be determined.
Reasons for insufficient draft:
A) Leaking chimney - Air leaking in around a loose fitting cleanout
door, joints or seams in connector pipe are not secured properly,
cracks or other defects in masonry.
B) Improper chimney height - Chimney does not extend to a
sufficient height above the roof line. (Remember the 3 ft.-2 ft.-10
ft. rule)
C) Obstructions in the chimney - Make sure the chimney has been cleaned. Different animals have been known to build nests in
chimneys.
-10-
D) Trees or other topographical barriers - Trees that are taller than the house can cause the air currents to ?ow downward over
the peak of the roof. This would lead to a down draft effect on the chimney. This can also be caused by adjacent buildings or
structures. It could even be from a different peak on the same structure.
E) Improperly sized flue - Too small of a chimney is incapable of moving the volume of air necessary. Too large of a flue could
have trouble warming up to create the necessary upward flow.
F) Chimney offsets - Offset chimneys should be avoided if possible. Not only can the offset affect draft, it is also a place for debris
to collect over time.
G) Too many elbows - The flue connector has more than two elbows in it. Sometimes, depending on overall chimney
performance, one elbow could be too many.
H) Vent sharing - No more than one heating appliance shall vent into a single flue.
THE MOST IMPORTANT THING TO REMEMBER ABOUT CHIMNEYS IS THEIR NEED FOR MAINTENANCE AND CLEANING. IF
A CHIMNEY IS NOT CLEANED ON A FREQUENT BASIS, IT WILL AFFECT DRAFT, AS WELL AS BE A CONTRIBUTING
FACTOR TO A POTENTIAL CHIMNEY FIRE.
3.3 WHAT TO DO IF YOU HAVE A PROBLEM.
If you have a chimney fire:
1. Be sure everyone is out of the house.
2. Call the fire department.
3. Close the draft control on the ash door and make sure both doors on the stove are closed and latched.
4. Do not put water on the fire, this will cause unnecessary damage to the stove and flue.
5. Have the chimney inspected and repaired prior to building another fire.
Smoke puffs out of the stove:
1. Check previous suggestions for insufficient draft.
2. Check draft control for proper operation.
3. Chimney may be too low. Increase height.
4. Add more fresh air to the room. Your home may be so tight that there is not enough oxygen getting to the ?re.
5. Remember, open the draft control and crack the door open slightly before
reloading or checking the ?re.
6. Check the ashes. The ash pan and firebox may be overloaded with ashes.
7. Check the chimney cleanout door to ensure it closes properly.
WARNING - DO NOT CONNECT THIS UNIT TO A CHIMNEY SERVING
ANOTHER APPLIANCE!
3.4 MAGNAFIRE CHIMNEY SPECIFICS
A) Flue connecting pipe must not be less than 6 inches in diameter and of 24
gauge or heavier.
B) Connecting pipe joints are to be secured with screws (preferred) or pop
rivets. Suggested location for fasteners is at the 12/4/8 o’clock positions.
Refractory cement may be used at stove and chimney collar to secure these
connections. Keep in mind that disassembly may be perioically needed, so that
the chimney and connecting pipe may be cleaned and inspected.
C) Masonry Chimney Connections - A minimum of 12 inches of solid masonry is
required around a 5/8 inch thimble if the pipe passes through a combustible
wall. It is also acceptable to use a UL listed prefabricated wall pass through. If
such a pass through is used, all the components comprising a complete pass
through kit must be included, as per manufacturer’s recommendations.
-11-
D) Masonry Fireplace Chimney Connections - In some situations, a code
compliant chimney originally used for a masonry fireplace may be used.
The chimney must be lined with the needs of the heating appliance in
mind, including minimum and maximum sizes. The lining will comply
with one of the following:
• Clay flue lining complying with the requirements of ASTM C315 or
equivalent.
• Listed chimney lining systems complying with UL 1777.
• Factory-built chimneys or chimney units listed for installation
within masonry chimneys.
• Other approved materials that will resist corrosion, erosion,
softening, or cracking from flue gases and condensate at
temperatures up to 1,800º F. (982º C)
Insulated liners work best for maintaining good draft. In addition to the
requirements found in the previous paragraphs, it is important to be aware that
all clearances must be met, including those from the chimney connector to
combustibles. Do not forget to include floor protection in your plans. (See
Clearances and Floor Protection) Since many fireplaces have exposed wooden
mantels and trim, pay special attention to the clearances necessary to these
materials. If your fireplace chimney is behind a combustible wall, you must use
an approved wall pass-through system to gain access to the masonry chimney.
The chimney connector must enter the chimney at a place where it is lined, and
the fireplace must be made inoperable. For example, you might remove the
damper, replacing it with a secure, airtight, noncombustible seal (removable for
inspection); this also satisfies the requirement that no room air must be allowed
to enter the chimney.
WARNING!
DO NOT BURN ANY FUEL OTHER THAN COAL. NEVER USE
HIGHLY VOLATILE SUBSTANCES IN YOUR STOVE, SUCH AS
GASOLINE, WHICH COULD CAUSE AN EXPLOSION. KEEP ALL
SUCH LIQUIDS AWAY FROM HEATER WHILE IN USE.
-12-
E) Manufactured Chimney Connections - When venting
using a prefabricated chimney, be sure to contact local
building code authorities, and to follow the
manufacturer’s instructions
USE ONLY THE MANUFACTURER’S PARTS. DO NOT
USE MAKESHIFT INSTALLATION TECHNIQUES. ALL
PREFABRICATED CHIMNEYS MUST BE TESTED TO
EITHER THE U.S. OR CANADIAN HIGH
TEMPERATURE STANDARDS, UL 103 OR ULC S629.
Your manufactured chimney may contain more parts than
is shown at right. Include all required items in your
installation. A chimney cap (A) serves to keep rain and
snow from entering the chimney. An approved Class A
chimney (B) is required for the Super Magnam Stoker.
Wall Bands (C) must be deployed for support per
manufacturer’s recommendations. A manufacturer’s Wall
Support Kit (D) will contain required items for supporting
the chimney. Such kits will cost less than individual items
purchased separately. A Bottom Cap (E) allows for
cleaning. The arrow shows the location of the bottom end
cap, but it is not visible on the drawing. A Finishing
Collar (F) provides inside wall protection. A Wall Thimble
(G) provides for required clearance between the chimney
pipe passing through a flammable wall. The Chimney
Connector (H) must be approved single wall, or a low
clearance pipe, installed with required clearances in place.
A Roof Brace (I) is required for chimneys that extend
more than a certain distance, as referenced by the
manufacturer’s instructions, from the roof. Manufactured
chimneys may feature a built in “twist lock” at each joint,
but a Joint Band (J) is still normally required to secure
pipe at the joint. An approved Chimney Pipe Adapter (K)
is required. A Ceiling Support (L) will provide structural
support for the chimney and is typically part of a kit that
includes items that maintain required clearances to
flammables. A Storm Collar (M), and Adjustable Flashing
(N) prevent water from entering the home by running
down the outside of the chimney. Additional items or a kit
(O) provide additional mounting support or fire protection
to the roof joists or other roof components.
exactly
.
F) Draft Regulation - Barometric Damper Setup
A stove and chimney combination that drafts well will
occasionally produce more draft than is desired. Excessive
draft can lead to overfiring. It will also lead to reduced
efficiency, as more heat will end up going up the
chimney. A barometric damper is required to limit
maximum draft to -.08 column inches. The barometric
damper needs to be the same diameter as the stove collar.
It is to be installed in the chimney connecting pipe as
shown below.
-13-
Follow these steps to ensure safe and efficient operation of your Mark I or Mark III stove. You will need to start a fire in the appliance
to establish a draft in the chimney flue. Refer back to these instructions after reading the entire manual.
1. Drill a hole into the flue connector pipe, for the purpose of attaching a draft meter. This hole should be between the barometric
damper and the stove’s flue collar, and in an inconspicuous location, as it will be closed off after the test with a bolt.
2. Attach the draft meter to the hole in the connector. A great chimney will have draft without a fire or heat source. Set the
barometric damper to maintain -.06 to -.08 (inches of water column).
3. Remove the draft meter from the connector pipe and seal the hole by threading in a screw or bolt. You may also want to apply
a small dab of high-temperature silicone to the threads prior to installing.
4. Grates
4.1 GRATE SYSTEM AND CONTROLS
The Grates are made of heavy-duty cast iron. The function of the grate system is to support the coal while allowing air flow through
the fire. The grate system also allows removal of the ashes by shaking them through the grates. The grates are removable without the
use of tools, once the fire bricks are removed, the grates simply lift out. Lift the right end higher to disengage from the shaking link. To
re-install the grates, lower them, one at a time, left end first, be sure the grate hooks into the grate link as you drop it into place.
Your grates will last forever, as long as you keep your ashes cleaned out of the stove. When ashes are left to pile up against the
underside of the grates, the air-flow is blocked. With no air flow through the grates, they will begin to sag from the intense heat. The
grates are designed to accommodate three different sizes of anthracite coal. Pea is defined as being able to fit through a round screen
hole of 9/16” to 7/8”. Nut or Chestnut is defined as being able to fit through a round screen hole of 7/8” to 1½”. Finally, Stove coal which
is 1½” to 2½” in size. Pea or Nut you’ll find work the best for starting a fire, while all three sizes burn just as well. The external shaker
handle allows for greater safety from burns, and the convenience of needing no extra tools.
-14-
Operation
5. Operating Instructions
5.1 STARTING A FIREPLACE
Place seven or eight sheets of crumpled newspaper onto the top of the grates. Next, lay in some small kindling wood (approximately
3/4” or less) on top of the newspaper. Layer the kindling in a criss-cross fashion to allow for maximum air flow. Open the draft control
to it’s full open position. Light the paper nearest the center of the door opening and close and latch the load door. After two to three
minutes, open the load door an inch or two for a few seconds, then open it completely. This method is good practice to allow smoke to
clear away from the load door. Add a few small pieces of firewood when the kindling is burning well. Close the door again and be sure
the draft control remains open. The ash door itself may be opened for a short period to accelerate the process.
DO NOT LEAVE THE STOVE UNATTENDED WITH THE DOOR OPEN.
When a substantial bed of hot wood coals are built up, start adding small amounts of coal on top of the burning wood embers. (Pea or
Nut sized coal will give the best results when starting a fire.) Keep the draft control open through the whole ignition process. As the
coal begins to free-burn, continue adding small amounts until there is a solid bed of burning coal. Do not add too much at one time as
you could smother the fire. Allow sufficient time between these small batches so that the coal can ignite thoroughly before more is
added. Once a substantial bed is established, fill the firebox to the top of the bricks. A deep bed of coal will always burn better than a
shallow bed. Adjust the draft control to the desired heat output. You’ll learn over time that the coal fire does not instantly change with a
turn of the draft control. Make your adjustments in small increments and wait for the fire to stabilize. The normal range of control
settings will be from closed, for extended burn times, to one full turn open.
NOTE: If the ash door was opened during the lighting process, it must be closed to prevent over-firing. Over-firing can cause
dangerously high temperatures.
5.2 BLOWER OPERATION
Use of the blower will increase heat ouput of the stove. Be sure to use a 3-wire extension cord and to connect to a grounded outlet.
Route the cord to avoid creating a trip hazard, as well as to avoid the risk of abrasion damage to the insulation on the cord. Inspect the
power cord and extension cord at both the start and end of the season.
5.3 LOADING
Coal should never be added unless there is a reasonably hot fire. The coal bed should be bright and vigorous. If the fire is burning hot
and there is a deep bed of hot coals, full loads of coal can be added at any time. However, if there is not a deep bed of coals, it is best to
add in small batches as during lighting.
5.4 INCREASING HEAT FROM A LOW FIRE
Every effort should be made to not let a coal fire burn so long that it begins to die. This causes the reloading process to be much longer,
and there is a good possibility of losing the fire all together. Do not shake or stir a low fire. Open the draft control or the ash door to get
the maximum air flow. Allow the fire to get reasonably hot. If there is not enough unburned coal to renew the fire, add a small amount.
Continue adding coal in small amounts until a full bed is established. Now, shake the grates. (see next section “shaking ashes”)
5.5 SHAKING ASHES
Shaking should be done only when there is a hot fire. The frequency of shaking will depend on the rate of burning. Shaking should be
done at least once per day but best results will come from shaking twice a day. When shaking, do just that. Do not rock the handle in
long strokes, just shake it briskly until you see red hot ashes fall into the ash pan. Rocking the grates may allow pieces of coal to jam
them in an open position.
DO NOT LEAVE THE STOVE UNATTENDED WITH THE DOOR OPEN
5.6 ASHES AND THEIR REMOVAL
Ashes should be placed in a metal container with a tight fitting lid, pending final disposal. The closed container of ashes should be
placed on a non-combustible floor or on the ground, well away from any combustible materials. If the ashes are disposed of by burial in
soil or otherwise locally dispersed, they should be retained in the sealed container until all cinders have thoroughly cooled. Coal
produces considerably more ash than wood. For equal heat output, coal will produce 7 to 10 times the ash of a wood fire.
CAUTION! ASHES SHOULD NEVER BE ALLOWED TO ACCUMULATE ABOVE THE TOP OF THE ASH PAN. ASHES IN
CONTACT WITH THE BOTTOM OF THE GRATES ACT AS AN INSULATOR INTENSIFYING THE HEAT ON THE GRATES, AND
WILL CAUSE THE GRATES TO WARP. GRATE DAMAGE FROM ASH BUILD UP IS EASILY RECOGNIZED. PLEASE REFER TO
YOUR WARRANTY TO SEE LEGACY STOVESTM LIMIT OF LIABILITY IN CASES OF ABUSE OR NEGLECT.
-15-
5.7 SAFETY
Whenever a loading door is opened, it should always be cracked slightly to allow oxygen to enter and burn any gasses that may be
present. Failure to do this may result in a sudden ignition of the gasses, leading to an explosion. A stove should never be filled with
excess coal to where the exhaust is impeded. burning coal generates carbon monoxide. If the flue gas exit is blocked, the carbon
monoxide can be forced out of the stove and into your living space, with fatal consequences.
CAUTION! DO NOT BANK THE FIRE SUCH THAT COAL WILL ROLL INTO THE LOAD DOOR OPENING, OR AGAINST THE
GLASS!
With the exception of start-up or freshening a fire, the ash pan door should never be left open. NEVER LEAVE THE STOVE
UNATTENDED WITH A DOOR OPEN. Serious damage to the stove can occur from overheating. Coal stoves should not be installed in
a chimney that has a history of down-draft or flow reversal problems. These conditions can cause improper draft, resulting in carbon
monoxide entering the living space rather than being drawn up the chimney. REMEMBER! COAL GASES ARE TOXIC! Sulfur dioxide,
sulfur trioxide and other products of coal combustion may corrode stainless steel and masonry chimneys. Coal with high sulfur content
will destroy chimneys especially fast if soot is left in the flue for extended periods. It is important to clean your chimney regularly.
5.8 CONTROLLED FIRING
Also key to operational safety is avoiding overfiring the stove. This stove features a manually set air intake damper, mounted on the
ash door. This consists of a cast, threaded dial, which when turned, allows for adjusting an air gap between the dial and the ash door.
Once a fire is established, the main factors determining the position of the intake damper are how much heat is needed and the need to
limit overfiring. Stove parts or chimney connectors glowing red are a sure indicator that the damper should be closed down. A chimney
connector thermometer is highly recommended for setting the maximum air setting. This can be placed in the first straight section of
the chimney connector. As temperatures approach 450º F, limit air so as to reduce the intensity of the fire. Lower temperatures are an
indicator of more efficient operation. Keep load doors and ash doors closed, except when attending to or starting fires. Maintain door
gaskets in good condition, and inspect them before, during and after the heating season.
CAUTION! DO NOT REMOVE THE AIR INTAKE DAMPER CONTROL, OR MODIFY IT IN ANY WAY. DOING SO WILL VOID
YOUR WARRANTY, AS WELL AS PRESENT A FIRE HAZARD!
CAUTION! MAINTAIN LOAD DOOR AND ASH DOOR GASKETS TO AVOID OVERFIRING!
6. Maintenance
6.1 PERIODIC AND EVERYDAY MAINTENANCE
Blower: Monthly, remove the blower and clean the fan. If there are pets in your house, you may want to check this more frequently.
Grates: Keep ash pan emptied twice a day.
INSPECT AND CLEAN STOVE, CONNECTING PIPE AND CHIMNEY EVERY TWO MONTHS.
Chimney and connector: Avoid chimney fires. Creosote may form in your venting system during the wood fired startup period,
particularly if fires are restarted frequently. When coal is burned, the products of combustion combine with moisture to form a soot
residue which accumulates on the flue lining. When ignited, this soot makes an extremely hot fire. The chimney connector and
chimney should be inspected at least once evey two months during the heating season to determine if soot and or creosote buildup has
occurred. The baffle area inside the stove, the chimney connecting pipe, and the chimney must be kept clean. Steel brushes are the
safest for cleaning metal surfaces. Salt solutions and other chemicals may damage the metal surfaces.
WARNING! DO NOT STORE KINDLING FOR STARTING FIRES WITHIN CLEARANCES LISTED FOR COMBUSTIBLES.
To clean the chimney, use a stiff brush with an extendable handle. Start the brush
from the top of the chimney and run it down through the flue. Continue brushing
until the entire length of the chimney is cleaned. The debris will collect at the
bottom of the chimney. Open the cleanout door or other access point and sweep the
collection into a metal container. The connector pipe can be brushed also, remove it
from the stove if possible, to eliminate pushing the debris into the stove’s spiral
chamber.
Ashes should be kept in a metal container with a tight fitting lid. The closed
container of ashes should be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally dispersed, they should be kept in
the closed container until all cinders have thoroughly cooled. Do not use this same
container for garbage, debris, or lawn waste.
-16-
6.2 COAL/FUEL HANDLING AND STORAGE
Reserve an area for storing coal that will serve to keep it dry. Coal does not deteriorate with moisture, but it is best if it is dry when
loaded into the stove. Coal purchased in bags may have been dampened to control dust. If stored in below freezing temperatures, bring
bags into a warmer area to allow for thawing. This assures that the coal can be added to the stove in a loose and free flowing form.
Wood stored to be used for starting fires should be stored well beyond all clearances to combustibles and outside of all service areas
needed to provide access to the stove. Very dry wood will assist greatly in starting fires.
6.3 GLASS DOORS – MAINTENANCE
Air washing over the glass in the load doors is generally sufficient to clean them, allowing for an unobstructed view of the fire. Should
it be necessary to clean the glass, allow the fire to go out and clean the glass after it has cooled. Use a soft rag, dampened with a mild
detergent to wipe the inside and outside of the glass, if needed. DO NOT use an abrasive cleaner. NEVER clean the glass when hot.
When opening the load door, make sure the path of travel is unobstructed with anything that might impact the door glass. When
closing the load door, never slam the door shut. Do not store items near the front of the stove that may fall and impact the glass and
cause breakage.
WARNING! DO NOT USE ABRASIVE CLEANERS ON GLASS. DO NOT CLEAN GLASS WHEN HOT!
CAUTION! DO NOT OPERATE STOVE WITH BROKEN GLASS!
6.4 GLASS DOORS – GLASS REPLACEMENT
Should the glass in the load door break, do NOT operate the stove with a broken glass. It will be necessary to replace the glass. NEVER
replace the glass with a generic item. ALWAYS use the proper replacement part from your Legacy Stoves dealer. Refer to parts list
near end of this manual.
WARNING! DO NOT USE A SUBSTITUE PART TO REPLACE GLASS OR OTHER ITEMS ON YOUR STOVE. USE ONLY
MANUFACTURER PROVIDED PARTS PURCHASED THROUGH YOUR DEALER.
To replace your glass, lift up on the load door to remove it from the front of the stove, and lay it frontside down on a flat surface lined
with a thick cloth. Remove the four capscrews (designated as “A” below) that secure the glass retainer to the door.
CAUTION! WEAR GLOVES WHEN HANDLING BROKEN GLASS DURING THIS REPLACEMENT!
Lift the glass retainer from the door, then remove and discard the broken glass from the door.
-17-
Position the glass within the door, and reinstall the retainer and the four capscrews.
-18-
7. Warranty Information
Warranty Period AHS Manufactured Appliances and Venting
Components Covered
Parts Labor Coal and Wood Coal Venting
1 Year x x x
2 years x x
3 years x x Firebox and heat exchanger
90 Days x x x
See conditions, exclusions, and limitations on next page
All parts and material except
as covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic
components, and glass
Factory-installed blowers
Limited
Lifetime
All replacement parts beyond
warranty period
Alternate Heating Systems
LIFETIME LIMITED WARRANTY
Alternate Heating Systems, on behalf of its hearth brands (”AHS”), extends the following warranty for AHS gas, wood,
pellet, coal and electric hearth appliances that are purchased from an AHS authorized dealer.
WARRANTY COVERAGE:
AHS warrants to the original owner of the AHS appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the AHS appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered
components manufactured by AHS are found to be defective in materials or workmanship during the applicable warranty
period, AHS will, at its option, repair or replace the covered components. AHS, at its own discretion, may fully discharge
all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the
product itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This
warranty is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized AHS dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from AHS, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table. The term “Limited Lifetime” in the table below is
defined as: 20 years from the beginning date of warranty coverage for gas appliances, and 10 years from the beginning
date of warranty coverage for wood, pellet, and coal appliances. These time periods reflect the minimum expected useful
lives of the designated components under normal operating conditions.
-19-
Page 1 of 2
WARRANTY CONDITIONS:
• This warranty only covers AHS appliances that are purchased through an AHS authorized dealer or distributor. A
list of AHS authorized dealers is available on the AHS branded websites.
• This warranty is only valid while the AHS appliance remains at the site of original installation.
• This warranty is only valid in the country in which the AHS authorized dealer or distributor that sold the appliance
resides.
• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts,
contact the nearest AHS authorized dealer or supplier. Additional service fees may apply if you are seeking
warranty service from a dealer other than the dealer from whom you originally purchased the product.
• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping
charges for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or
other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include:
paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints
related to this noise are not covered by this warranty.
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to install
the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse,
misuse, continued operation with damaged, corroded or failed components, accident, or improperly/ incorrectly performed
repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly sealed
constructions, insufficient make-up air supply, or handling devices such as exhaust fans or forced air furnaces or other
such causes; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components
not supplied with the appliance or any other components not expressly authorized and approved by AHS; (8) modification
of the appliance not expressly authorized and approved by AHS in writing; and/or (9) interruptions or fluctuations of
electrical power supply to the appliance.
Non-AHS venting components, hearth components or other accessories used in conjunction with the appliance.
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
AHS’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information
is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must
be given to appliance location and configuration, environmental conditions, insulation and air tightness of the structure.
This warranty is void if:
• The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other
damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast
iron, bubbling, cracking and discoloration of steel or enamel finishes.
• The appliance is subjected to prolonged periods of dampness or condensation. There is any damage to the
appliance or other components due to water or weather damage which is the result of, but not limited to, improper
chimney or venting installation.
LIMITATIONS OF LIABILITY:
The owner’s exclusive remedy and AHS’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event
will AHS be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not
allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This
warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE
EXTENT PROVIDED BY LAW, AHS MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED
HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED
WARRANTY SPECIFIED ABOVE.
Page 2 of 2
-20-
8. Service Parts
Item Description Comments Part Number
1
Load Door – Roped 1-10-08145A
Door Kit Assembly Black Classic 1-00-00139-1
Door Kit Assembly – Gold No Longer Available 1-00-00139-4
2
Glass Frame Cast 4-00-00038-1
Glass Frame – Gold No Longer Available 3-00-00038-4
3-40-7251050
3 Spring Handle 1/2 Pkg of 3 3-40-00086-3-3
4 1-10-01001
5 Ash Door – Roped 1-10-08143A
Draft Control Cast 4-00-00109-1
Draft Control – Gold No Longer Available 3-00-00109-4
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer. Provide
model number and serial number when requesting service parts from your dealer.
Rect Glass 7-1/4 X 10-1/2
Short Shaker Handle Weldment
Service Parts – Mark I
Magnafire Freestanding Coal Stove Beginning Mfrg Date: N/A
1-90-03224-1 (Black w/Door) Ending Mfrg Date: Active
1-70-03224-1 (Black), Ending Manufacturing Date: June 2011
1-70-03224-2 (Charcoal) Ending Manufacturing Date: June 2011
1-70-03224-3 (Goldenfire) Ending Manufacturing Date: June 2011
Retired Units
1-70-03224-4 (Metallic Blue) Ending Manufacturing Date: Jan 2010
1-70-03224-10 (Mojave Red) Ending Manufacturing Date: Jan 2010,
1-70-03224-12 (Forest Green) Ending Manufacturing Date: Jan 2010
Additional service parts on following page
-21-
Service Parts (continued) Mark I
Item Description Comments Part Number
Ash Pan 1-10-65127
Baffle 2-00-00503B
Blower - 75cfm, 7ft Cord 3-21-07584
Brick 9” X 4-1/2” x 1-1/4”
Pkg of 7 1-00-900450125
3-40-900450-414
Brick Angles 2-00-01100-2S
Brick Bracket 2-00-01006
Brick Set 1-00-0836
Door Handle – Cast 4-00-00042
Door Hinge 2-00-07203D
Door Latch 4 Sets 1-00-00036
Door Pin 3/8 X 1-7/8 (Ash Pan & Load Door) Pkg of 4 4-30-00138B
Gasket 1/2 IN Round Rope (Load Door – Ash Door) 20 FT 1-00-53500
Gasket Glue, 32 OZ 3-42-4583
Gasket, 5/8 IN Channel (Glass) 5 FT 1-00-98187
Grate Holder 2 – Cast 3-00-00193
Grate Link 2 Cast 3-00-00203
Mag Grate 15 IN – Cast (2 per) 3-00-00208
Mag Leg – Cast 4-00-00044P
1-10-02015W
Shaker Block 2-00-01037-1
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer. Provide model
number and serial number when requesting service parts from your dealer.
414 Pcs
Qty 2 req
Qty 4 req
Qty 2 req
Shaker Bar Weldment 1-1/2 IN
Beginning Mfrg Date: N/A
Ending Mfrg Date: Active
-22-
Service Parts Mark II
Item Description Comments Part Number
1
Load Door – Roped 1-10-08140A
Door Kit Assembly Black Classic 1-00-00141-1
Door Kit Assembly – Gold No Longer Available 1-00-00141-4
2
Glass Frame Cast 4-00-00037-1
Glass Frame – Gold No Longer Available 3-00-00037-4
Rect Glass 8-1/2 IN X 14-15/16 IN 3-40-8501494
Rect Glass 4-1/2 IN X 8-1/2 IN (Triple Frame) 3-40-450850
3 Spring Handle 1/2 Pkg of 3 3-40-00086-3-3
4 Short Shaker Handle Weldment 1-10-01001
5 Ash Door – Roped 4-00-00213D
Draft Control Cast 4-00-00109-1
Draft Control – Gold No Longer Available 3-00-00109-4
Additional items on next page
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer. Provide model number
and serial number when requesting service parts from your dealer.
Beginning Manufacturing Date: N/A
Ending Manufacturing Date: Nov 2013
-23-
Service Parts (continued) Mark II
Item Description Comments Part Number
Ash Door, Roped 1-10-08142A
Ash Pan 1-10-00722
Baffle 2-00-00360B
Blower – 75cfm, 7ft Cord 3-21-07584
Brick 9” X 4-1/2” x 1-1/4”
Pkg of 7 1-00-900450125
3-40-900450-414
Brick, Set of Cut 1-00-00837
Brick Angle Qty 2 req 2-00-01100-2S
Brick Bracket 2-00-01006
Door Handle Cast 4-00-00042
Door Hinge Qty 4 req 2-00-07203D
Door Latch 4 Sets 1-00-00036
Door Pin 3/8 X 1-7/8 (Ash Pan) Pkg of 4 4-30-00138B
Door Pin 3/8 X 2-1/4 (Load Door) Pkg of 4 4-30-00138A
Gasket 5/8 IN Channel (Glass) 5 FT 1-00-98187
Gasket 1/2 IN Round Rope (Load Door – Ash Door) 20 FT 1-00-53500
Gasket Glue, 32 OZ 3-42-4583
Gasket, 5/8 IN Channel (Glass) 5 FT 1-00-98187
Grate Holder – Cast Qty 2 req 3-00-00193
Grate Link 2 - Cast 3-00-00203
Hot Water Coil 3-10-49201
Hot Water Coil Hardware 3-10-49000
Mag Grate 20 IN – Cast Qty 2 Req 3-00-00211
Mag Leg – Cast 4-00-00044P
Screw, Hex Cap, 5/16-18 X 3/4 IN Grade 5 Zinc Plated Pkg of 100 3-30-1125-100
Shaker Bar Weldment 1-1/2 IN 1-10-02015W
Shaker Block 2-00-01037-1
Shaker Handle Mount 2-00-01037-2
Touch up Paint, Aerosol, Black
Pre 008461796 3-42-1990
Post 008461796 3-42-19905
Washer, Split Lock, 5/16 IN Zinc Plated Pkg of 100 3-30-0101-100
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer. Provide model number and
serial number when requesting service parts from your dealer.
414 Pcs
Beginning Manufacturing Date: N/A
Ending Manufacturing Date: Nov 2013
-24-
Service Parts Mark III
Item Description Comments Part Number
1
Load Door – Roped 1-10-08140A
Door Kit Assembly Black Classic 1-00-00141-1
Door Kit Assembly – Gold No Longer Available 1-00-00141-4
2
Glass Frame Cast 4-00-00037-1
Glass Frame – Gold No Longer Available 3-00-00037-4
Rect Glass 7-1/4 X 10-1/2 3-40-450850
3 Spring Handle 1/2 Pkg of 3 3-40-00086-3-3
4 Short Shaker Handle Weldment 1-10-01001
5
Ash Door Cast 4-00-00213D
Draft Control Cast 4-00-00109-1
Draft Control – Gold No Longer Available 3-00-00109-4
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer. Provide
model number and serial number when requesting service parts from your dealer.
Magnafire Freestanding Coal Stove Beginning Mfrg Date: N/A
1-90-03227-1 (Black w/Door) Ending Mfrg Date: Active
1-70-03227-1 (Black) Ending Manufacturing Date: June 2011
1-70-03227-2 (Charcoal) Ending Manufacturing Date: June 2011
1-70-03227-3 (Goldenfire) Ending Manufacturing Date: June 2011
1-70-03227-4 (Blue) Ending Manufacturing Date: Jan 2010
1-70-03227-5 (Honey Glo) Ending Manufacturing Date: June 2009
1-70-03227-10 (Mojave Red) Ending Manufacturing Date: Jan 2010
1-70-03227-12 (Forest Green) Ending Manufacturing Date: Jan 2010
1-90-03228-1 (Black) Ending Manuafcturing Date: Sept 2013
Retired Units
1-70-03228-1 (Black) Ending Manufacturing Date: June 2011
1-70-03228-2 (Charcoal) Ending Manufacturing Date: June 2011
1-70-03228-3 (Gold, Ending Manufacturing Date: June 2011
1-70-03228-4 (Blue) Ending Manufacturing Date: Jan 2010
1-70-03228-5 (Honey Glo) Ending Manufacturing Date: July 2009
1-70-03228-10 (Mojave Red) Ending Manufacturing Date: Jan 2010
1-70-03228-12 (Forest Green) Ending Manufacturing Date: Jan 2010
Additional service parts on following page
-25-
Service Parts (continued) Mark III
Item Description Comments Part Number
Ash Door, Roped 1-10-08142A
Ash Pan 1-10-00723
Baffle 2-00-00378B
Blower – 135cfm, 7ft Cord 3-21-13584
Bolt, 1/4-20 X 1/2 IN Grade 8.2 Zinc SAE Flange Pkg of 50 3-30-2001-50
Brick 9” X 4-1/2” x 1-1/4”
Pkg of 7 1-00-900450125
3-40-900450-414
Brick, Set of Cut 1-00-00838
Brick Bracket 2-00-01006
Door Handle Cast 4-00-00042
Door Hinge Qty 4 req 2-00-07203D
Door Latch 4 Sets 1-00-00036
Door Pin 3/8 X 1-7/8 (Ash Pan) Pkg of 4 4-30-00138B
Door Pin 3/8 X 2-1/4 (Load Door) Pkg of 4 4-30-00138A
Gasket 5/8 IN Channel (Glass) 5 FT 1-00-98187
Gasket 1/2 IN Round Rope (Load Door – Ash Door) 20 FT 1-00-53500
Gasket Glue, 32 OZ 3-42-4583
Gasket, 5/8 IN Channel (Glass) 5 FT 1-00-98187
Grate Holder – Cast Qty 2 req 3-00-00194
Grate Link - Cast 3-00-00204
Hot Water Coil 3-10-49201
Hot Water Coil Hardware 3-10-49000
Mag Grate 20 IN – Cast Qty 3 Req 3-00-00211
Mag Leg – Cast 4-00-00044P
Shaker Bar Weldment 1-1/2 IN 1-10-02015W
Shaker Block 2-00-01037-1
Shaker Handle Mount 2-00-01037-2
Side Brick Angle 2-00-01100-1D
Touch up Paint, Aerosol, Black
Pre 008461796 3-42-1990
Post 008461796 3-42-19905
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer. Provide model
number and serial number when requesting service parts from your dealer.
414 Pcs
-26-
Beginning Mfrg Date: N/A
Ending Mfrg Date: Active
Service and Maintenance Log
Date of Service Performed By Description of Service
-27-
Service and Maintenance Log
Date of Service Performed By Description of Service
-28-
Advanced Design
Old Fashioned Values
(Signature of Boxer)
Your premium quality hearth product designed and assembled
by the experienced and skilled members at Alternate Heating
Systems in Harrisonville, PA, USA.
-29-
Loading...