Lee & Plumpton Signature Storage Series Operators Manual
1
A/1877 Revision A 29/01/2018
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE
Signature Storage, Cupboard.
REF:
740mm High, 1000mm High, 1200mm High,
1600mm High, 1800mm High, 2000mm High
800mm and 1000mm Wide
Read this leaet before
assembly
2 People
Required
COMPONENT PARTS
Item 10
A.0718
Bar Handle
Qty 2
Item 11
A.0551
CU Door Lock
Qty 1
Item 12
A.0552
Cupboard Door
Bolt
Qty 2
Item 13
A.0558
Angled Striker Plate
Qty 2
Item 14
A.0559
Cupboard Lock Strike
Plate
Qty 1
Item 15
A.0592 A.0593 A.0594
Blum 100 Hinge
Qty, (See Table 1)
Item 16
D.0362
Lock Rosette
Qty 1
Item 17
F.0629
Rapid Dowel (Blue)
Qty, (See Table 1)
Item 18
F.0630
Rastex Cam
Qty, (See Table 1)
Item 19
F.0431
Wood Dowel
Qty 10
Item 20
F.0436, F.0446, F.0545,
F.0575, F.0576, F.0577
Cam Cover
Qty, (See Table 1)
Item 21
F.0404A
Kd Block Female (Brown)
Qty2
Item 22
F.0404B
Kd Block Male (Natural)
Qty 2
Item 25
F.0469
M4x28 Handle
Screw
Qty 4
Item 26
F.0470
34“x6g CSK Pozi BZP
Qty 4
Item 28
F.0442
5 8” x 4g CSK BZP
Qty 3
Item 29
F.0413
5 8” x 6g Pan BZP
Qty 4
Item 30
F.0564
Shelf Support
Qty 4
Item 31
F.0492
16mm Euro Screw
Qty 4
Item 5
STO1_643
Top Panel
Qty 1
Item 6
STO1_644
Bottom Panel
Qty 1
Item 4
STO1_592
Lintel
Qty 1
Item 2
STO1_538
LH Side Panel
Qty 1
Item 1
STO1_654
Back Panel
Qty 1
Item 3
STO1_536
RH Side Panel
Qty 1
2
A/1877 Revision A 29/01/2018
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
COMPONENT PART QUANTITIES FOR UNIT SIZE VARIATIONS (TABLE 1)
• Pozi head screwdriver
• Hammer
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
ITEM W 800 x H 740 mm W 1000 x H 740 mm W 800 x H 1000mm W 1000 x H 1000 mm W 800 x H 1200 mm W 1000 x H 1200 mm
17
22 24 24 26 24 26
18
22 24 24 26 24 26
20
22 24 24 26 24 26
15
4 4 4 4 4 4
ITEM W 800 x H 1600 mm W 1000 x H 1600 mm W 800 x H 1800mm W 1000 x H 1800 mm W 800 x H 2000 mm W 1000 x H 2000 mm
17
26 28 26 28 26 28
18
26 28 26 28 26 28
20
26 28 26 28 26 28
15
6 6 6 6 6 6
IMPORTANT
4 shelf units must be xed to the wall for stability.
18
Lay the Back (1) at on a soft
surface. Ensure all holes are free
of debris.
Insert the appropriate number of
Wooden Dowels (19) and Cams
(18).
Ensure that the arrow moulded
into the Cams are pointing
towards the edge of the panel.
19
1
Lay the Left Side (2) and Right Side
(3) at on a soft surface. Ensure all
holes are free of debris.
Insert the appropriate number of
Dowels (17) into the sides. Knock a
Male KDBlock (22) into each side.
In the Lintel (4) knock the female
KDBlocks (21).
Place both Sides into position on
the Back. Before tightening the
Cams, t the Lintel between the
Sides. Lock the Cams with a half
turn and tighten the screws in the
KD Fittings on the Lintel.
17
22
21
4
2
3
Loading...