LEEDS WORLD 1690-97 Start Manual
1.4” Photo Gallery Digital Photo Frame Start Guide
1690-97
Select
Mode:
Toggles display of time and alarm
Up
Set:
Push this button to set the time
Down
Adjust: Toggles the alarm, and the
display of US and International Time
Set the Clock in the Top Screen:
Before Using, Charge the Photo Frame
Plug the USB power cord into a PC a nd the Photo Frame.
Contents: Set the Bottom Screen Time: Set the Alarm in the Bottom Screen:
Controls and Connections:
Charge the Leed’s Photo Frame
Bottom Screen Controls
Top Screen
Controls
Bottom LCD Screen
Displays Time,
Alarm and Temperature
Mini-USB Jack
For transferring images
and charging Top LCD
To p
LCD
Screen
Battery Cover
L1130 batteries (2) for the Bottom LCD
Mode
Toggles the display between showing
the time and showing the alarm. Push
once or twice to ensure the clock shows
the time with seconds.
Up/Down
Toggle the display between
U.S. and International Time.
Up/Down
Increase or decrease the ashing number.
Select:
Hold the Select button for two seconds, and the
numbers on the display begin ashing. Quickly
pushing the Select button cycles through the elds
in this order:
Mode
Toggles the display between showing the time and
showing the alarm. Push once or twice to ensure
the clock shows the alarm (time displays without
seconds).
Set
Push once to change the Hour
(Hour should start to ash).
Set
When the hour is correct, press Set to
move to minutes. The minutes should
now begin ashing.
Set
When the minute is correct, press Set to
move to seconds.
Set
Push to stop any numbers from ashing.
The clock is set.
Adjust
Push once to increase by one hour.
Hold the button in to increase the hours
automatically.
Adjust
Push once to increase by one minute.
Hold the button in to increase the
minutes automatically.
Adjust
Push once to reset the seconds to zero.
You cannot set the seconds manually.
Up
Down
Select
Select “USB Charge” using the
UP/DOWN buttons below, and
click to charge the Leed’s Frame
In the bottom left of the display,
the batter y icon will ash. When
completely charged, it will stop.
NOTE: The battery should be completely charged before use.
To get the longest life from the battery, it should be completely
emptie d and fully charged for the rst th ree charge cycles .
Setting the alarm is much the same as the clock,
but with the difference that there is no seconds to set. Instead
of resetting the seconds, there is the alarm melody selection.
2
Photo Frame
3
USB Power Cord
1
User Manual
©2008-2009 LEEDSWORLD
Proprietary information contained in this document is the sole property of Leedsworld.
Any reproduction in part or as a whole without written permission of Leedsworld is prohibited.
1.4” Photo Gallery Digital Photo Frame Start Guide
1690-97
Viewing Photos:
Install Photo Viewer Software
Transfer Photos Using Photo Viewer
Drivers automatically install
the rst time this digital
photo frame is connected
to a computer.
It may take a few moments
for this process to complete.
3
Requires Microsoft Windows™ (not Mac compatible).
This frame contains a built-in installer
for the software used to transfer photos
from a computer.
Connect the frame and
computer with a USB cable.
1 2
Up
Down
Select
Use the UP/DOWN buttons
below to select “USB Update” is
selected, and click to connect the
Leed’s Photo Frame
The Top Screen now displays a
‘connected’ symbol; photos are
no longer d isplayed.
4
Windows recognizes the drive,
and the following
window appears:
Click “Run the
Program,” and
click “OK” to
continue.
NOTE: If an error occurs, try unplugging the
frame and insert an unbent paperclip into
the “Reset” button on the back of the frame,
then reconnect.
“Photo Viewer Image Editor”
opens with three main panels:
5
File List
Image Editor
Device
©2009 LE EDSWORLD
Proprietary information contained in this document is the sole property of Leedsworld.
Any reprod uction in par t or as a whole witho ut written perm ission of Leeds world is prohib ited.
Eject the frame properly to avoid damaging the internal memory.
Press the close button to exit Photo Viewer.
Click “Yes” to conrm closing the program.
Eject the drive from Windows™ by clicking the icon in the task bar:
Click “Safely Remove USB Mass Storage Device.”
Eject the Frame
11
12
6
File List
JPEG, JPG, BMP and GIF images opened from the
computer are shown here before sent to the frame.
Note: Or iginal les a re not altere d
Click “Open”
to bring in
images from
the computer
8
Image Editor
When you select an image, it
displays in the Image Editor.
Here you can control how an
image is cropped using the
tools on the bottom.
7
Select an image for the frame.
Delete one or all images
if you change your mind
with these but tons
Sync to the Frame
10
New les transfer to the
Frame, and eliminates
those marked for
deletion.
9
From the File List or
Image Editor, click to
send images for transfer
to the Device p anel.
The Device Panel shows a list of
pictures currently on the frame,
and the pictures ready to sync.
Send to Device Panel
Once the Photo Frame is safely ejected from the computer
unplug the USB cord.
Select:
If the Top Screen is off, hold the Select
button for two seconds to turn on the
frame and show the time.
Push once more to start displaying the
photos. They advance automatically,
but using the Up and Down buttons
can force the next image to appear.
Loading...