Leedarson Lighting
Leedarson Zigbee LED Bulb
Quick User Guide
Draft
Ver.
Description
Time
V
V1.0
2019.2
THANK YOU
We appreciate the trust and confidence you have placed in LEEDARSON through the purchase of
Zigbee Light Bulb. We strive to continually create quality products designed to enhance your home. Visit us
online to see our full line of products available for your home improvement needs. Thank you for choosing
LEEDARSON!
Leedarson Lighting
Product Introduction
1.1 Basic Information
CONTROL YOUR LIGHTS FROM ANYWHERE in the world from the palm of your hand. The
Retrofit produces beautiful high quality light that you can dim or tune, and control from your
smartphone or tablet. Easy to setup, bulbs fit into your standard household sockets - no need for
installation by an electrician. A wireless network or remote controller is required to operate bulbs.
SET LIGHT SCENES: Create rich indirect light scenes in your home by dim or tune the light’s color
temperature from 2700 to 6500K . Schedule to turn on the lights so you don't come home to a dark
house. Set automated timers, or program the bulb to gradually increase brightness in the the morning
like the sunrise for a more pleasant, natural alarm.
SAVE ENERGY: LEEDARSON bulbs use up to 84% less energy than traditional incandescent bulbs
and last up to 25,000 hours making them a smart choice for energy conscious homes.
1.2 Special notes for Connected Bulbs
Line Voltage Dimmer
LEEDARSON does not recommended the use of a line voltage dimmer with connected bulbs. The
reason is that each connected bulb contains a radio and by reducing, or removing power through a line
voltage dimmer may cause the connected bulb to not function properly.
For dimming, LEEDARSON recommends using a compatible App (i.e., LEEDARSON’S LDS App) or
Leedarson Lighting
a compatible wireless switch that uses the same wireless protocol as the bulb.
1.3 Leave your fixture on
If your switch or fixture is OFF,or is turned OFF, then control and communication from the App, or
wireless switch, to the LED Bulb is lost.
Inclusion Procedure
The following are the general procedures for the Zigbee bulb to be “included” into the network:
1. Screw the bulb into a standard socket.
2. Turn on the bulb with your wall switch to apply power to the bulb.
a) If you’re not using a wall switch, then use your alternate method to apply power to the bulb.
3. Activate the “inclusion” mode on your Zigbee controller or gateway.
a) This may also be done through your associated app, if your ecosystem has that capability.
4. Toggle the wall-switch, from OFF, then to ON.
a) Or use your alternate method to toggle power from OFF, then to ON.
5. The LED bulb will flash once if it has been successfully “included” into your Zigbee network.
Note: If you are using 3rdpartyZigbee Controller or Gateway, please refer to 3rdParty’s instruction on
how to add a new device to your network.
Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset
procedures to clear the bulb’s settings.
1.4 Factory Reset Procedure
Physically switch the bulb on and off six (6) times for intervals of 0.5-2seconds. After the 6thtime, the
bulb will flash twice indicating that it’s successfully reset.
Leedarson Lighting
Warning
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: The grantee is not responsible for any changes or modifications not expressly approved by
the party responsible for compliance. Such modifications or changes could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.
Model No.
Rated Power(W)
Rated Volt.(V)
Frequency (Hz)
8Zy-A806ST-Q4R
9
120
60
8Zy-A806ST-Q4Z
9
120
60
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
IC 20cm RF
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the
radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements de la IC établies pour un
environnement non contrôé. Cet équipement doit être installé et fonctionner à au moins 20 cm de
distance d’un radiateur ou de votre corps.
Product List
Safety Instructions:
Please read, keep and follow these instructions before installation:
1) Switch off the power supply to the socket and allow sufficient time for the bulb to cool before
removing the bulb from the fitting
2) Warning: Risk of Electric Shock. Do not attempt to disassemble bulb.
Leedarson Lighting
Leedarson Lighting
3) Not suitable for use with standard wall dimmers
4) Suitable for use in operation environment between -4℉ and 104℉（-20℃ and 40℃）
5) Not for use in emergency lighting.
6) The bulb is not suitable for totally enclosed fixtures.
7) Do not clean the bulb when it is on and connected to the power supply
8) Do not place the bulb on hot surfaces
9) Dispose of this device in accordance with disposal laws in your area.
Loading...