Page 1
Building your success in IoT
Use Guide
ZB Smart Plug Mini
Page 2
WARNING:
②
①
③
• For indoor use only.
• Do not immerse in water or use the device in wet locations, e.g. bathrooms or
outdoors.
• The devices are not intended for use in locations where the temperature may be
less than actual room conditions, such as unheated warehouses or garages.
• The total current limit of the device is 10A. Do not exceed this value!
• If a direct short is created on the output, the Smart Plug will be damaged and no
longer function.
• Do not disassemble the product, or make repairs yourself. You run the risk of electric
shock and voiding the limited warranty. If you need service, please contact us.
• Do not connect after each other.
•
1 Package Contents
Smart Plug *1
Quick start guide*1
2 Product Description
The plug turns your electrical appliances smart by enabling you to control them
through the smart home APP on your phone at or away from home. It also enables
you to automatically switch appliances on and off according to a programmable
timer and measure the energy consumption.
① Socket: Converts your traditional outlet and enables your plugged-in appliance to
become Smart and controllable with the App
② Button: Press once to switch on or off; press and hold to reset
③ Indicator Light: when the plug is operating, the light is green; when the device is
turned off, the light changes to off
Page 3
Feature list:
Product Model
Model Name: 7C-PL-Z-A1
Power supply:
120VAC±10%, 60Hz
Rated load current:
10A
Power output
1200W
Operational temperature:
0℃-40℃
Radio protocol:
Zigbee 2.4G
Range:
About 40m indoors (depending
on building materials)
Action
Indicator
powering on plug, and waiting for being connected to
Gateway
LED indicator blinks in green slowly
successfully connected to Gateway
LED indicator keeps in green status for
10s, and then turns off
fail to be connected to Gateway
LED indicator turns off directly
lose connection to Gateway (after connection to
gateway)
LED indicator blinks in green quickly
Plug is "on" working model (after connection to
gateway)
LED indicator keeps in green status
Plug is "off" working model
LED indicator turns off
OTA, Reset
LED indicator blinks in red quickly
1) Remote Control: Turn your electronic device on and off from anywhere using the
mobile app.
2) Schedule: Set specific times for your device to turn on/off as setting connected
lighting turn on at 19:00 every Monday. Or like setting lights to come on at dusk or
turn off at sunrise.
3) Coutdown: set a countdown timer to have plug turn off automatically. As setting
after 30 minutes turn off automatically.
4) Supporting repeater role.
Specification
LED Indicator: Under normal working state, Green—on, Red—off.
Page 4
3 Installation and Operation
Step 1. Download and install the App
Get the Arnoo App for android or IOS from Google play or Apple store.
Step 2. Register and login
Open the app, and it will walk you through creating an account and login to the home
screen.
Step3. Connect the Smart Plug to the Gateway:
1. Plug the Smart Plug in the wall socket. The green LED should now blink once per
second. If it doesn’t, press the button on the Smart Plug for at least 5 seconds, until the
red LED starts to blink rapidly. Then release the button and verify that the green LED
blinks once per second.
2. Next, open the app and follow the usual steps to discover and connect a new device.
3. When the Smart Plug is connected, the green LED will stop blinking and the Smart
Plug will show up in the app
4. You can now switch the Smart Plug On and Off via the app, as well as via the button
on the Smart Plug itself. When On, the green LED is on, when Off, the green LED is off.
Factory-reset:
Press the button on the Smart Plug for at least 5 seconds, until the red LED starts to
blink rapidly. After that, the green LED will blink once a second, indicating that it can be
paired to a Gateway again.
Operation
1 on/ off
Click Plug icon to remote control on/off
2 timer countdown
Click timer countdown button to set timer countdown
Page 5
3. Schedule
Click setting icon on the right corner to start Plug setting that included Schedule setting
Page 6
FCC Statement
FCC ID:2AB2Q7CPLZA1
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note: The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if it is not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in an installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment in an outlet on a different circuit than the receiver.
4. Consult an experienced technician for help
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 8 inches (20 cm) between the radiator and your body.
IC Statement
IC :10256A-7CPLZA1
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
Page 7
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
IC 20cm RF
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
of 8 inches (20 cm) between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements de la IC é
tablies pour un environnement non contrôé. Cet équipement doit être installé et
fonctionner à au moins 20 cm de distance d’un radiateur ou de votre corps.
-----------------------------------------------------------------------------------------For more information, Welcome visit: www.leedarson.com.
Mail to: iot@leedarson.com
LEEDARSON LIGHTING CO., LTD.
XINGDA RD, XINGTAI INDUSTRIAL ZONE, CHANGTAI COUNTY, ZHANGZHOU,FUJIAN,
363900, CHINA
Loading...