Leedarson Lighting 7ASSVEH0 Users Manual

LEEDARSON Z-Wave Door/Window Sensor

Content:

Contact Sensor ................................................................................................................................................... 2

1. Product Introduction ............................................................................................................................ 2

2. Product Appearance ............................................................................................................................ 2

3. Specification ......................................................................................................................................... 3

4. Features/Capabilities: .......................................................................................................................... 3

5. Installation Position and Notes ............................................................................................................ 4

6. Product Installation .............................................................................................................................. 4

7. Product Usage ...................................................................................................................................... 5

8. Attention .............................................................................................................................................. 6

9. Z-Wave Command ................................................................................................................................ 7

7A-SS-VE-H0

2

Contact Sensor

Quick Start Guide

1. Product Introduction

The LEEDARSON Door/Window Sensor is a wireless sensor that is powered by a CR2 battery. The
door/window sensor lets you know when a door or window is opened, or closed, and can trigger different
actions in response to that open action or close action. This sensor uses the Z-Wave communication

module to connect with Z-Wave Gateway. This device can be adapted to use in the EU(868.42Mhz),
US(908.42MHz) or AU(921.42MHz). The door/window sensor supports the Over The Air (OTA) feature for
the product’s firmware upgrade. If you want your Door/Window Sensor to be a security device that uses
secure/encrypted messages to communicate in a Z-Wave network, then a security enabled Z-Wave
controller/gateway is needed.

2. Product Appearance

Product main components and function overview.

① Reset: Hold the key for 5s to reset the sensor. After reset, Door/Window Sensor will send

“Device_Reset_Locally” to the main controller and exclude it from the Z-Wave network when the button
is released. This procedure will reset the sensor to factory default.

② LED indicator: If sensor has not been added to controller, the LED will blink for than 5 seconds. Once

the device is joined to the network successfully, the LED will stay on for 3 seconds.

3

3. Specification

Detection Technology

Magnetic switch

Detective Range

20mm

Communication Protocol

Z-Wave

Radio Frequency

908.42MHz (US)

868.42MHz (EU)

921.42MHz (AU)

Wireless Range

More than 100m outdoors
Approximately 30m indoors (depending
on building materials)

Power Source

3V, CR2 *1

Battery Life

2 years

Mounting

Screws or 3M Tape

Operating Temperature

-10°C to 45°C

Operating Humidity

Up to 85% non-condensing

Certifications

CE/FCC, Z-Wave Plus

Dimensions (mm):

68.4.(L)*24.4(W)*21.5(H) for Main Body

44.4(L)*15(W)*13(H) for Magnetic Part

4. Features/Capabilities:

1. The LEEDARSON Door/Window Sensor contains a sensor body and a magnet.

2. The LEEDARSON Door/Window Sensor detects through the separation and combination of the main

body and the magnet.

3. Recommend installation distance between the sensor body and the magnet is 10MM.

4. The Sensor also anti-tamper functionality. Once the sensor is moved, it will notify the gateway.

5. The LEEDARSON Door/Window Sensor is powered by CR2 battery with 2 years battery life.

6. The LEEDARSON Door/Window Sensor is designed to be mounted on the door or windows.

7. The LEEDARSON Door/Window Sensor supports low battery alarm function.

8. The LEEDARSON Door/Window Sensor supports firmware OTA.

4

5. Installation Position and Notes

1. The sensor should be used indoors and away from sources of moisture.

2. The magnet and the main sensor must be less than 2cm apart. Main sensor must be affixed to the

door or window and the magnet must be affixed to the frame. The magnet and the main sensor
must separate when the door or window is opened.

3. The sensor should not be mounted on a metal frame.

6. Product Installation

This product can be mounted by screws or 3M adhesive tape. Install it according to the diagram below:

① Push the bracket upwards to separate it from the body, then fix the bracket on the door/window by

screw or 3M tape.

② Take off the bracket on the back, install battery into the body. The LED will slowly flash 3 times.

③ Be careful when installing the bracket back onto the body. The best approach is from the side.

④ Stick the magnet onto the moving part of the door/window, no further than 20mm from the sensor.