LEEDARSON Wave User Manual

We build your success in IoT.

LEEDARSON Motion sensor Pet Immunity Z-

Wave™

7CA-SS-VE-C0

Motion Sensor Pet

immunity

Quick Start Guide

1. Product Introduction

The Motion Sensor lets you know when movement is detected in a certain area and can
trigger different actions in response to that movement (or lack of movement). It supports
the pet immunity up to 80 lbs. This sensor integrated Z-Wave communication module to
connect with Z-Wave gateway, and this device can be adapted to EU(868.42Mhz) or
US(908.42MHz).

If you want your Motion Sensor to be a security device that use secure/encrypted
message to communicate in a Z-Wave network, then a security enabled Z-Wave controller
is needed.

The motion sensor can be included and operated in any Z-Wave network with other Z­Wave certified devices from other manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.

2. Product Appearance

Product appearance and function overview.

Specification

Detection angle

80 degrees

Detection distance

8 meters / 26.25 feet

LED

Bracket

Reset button

Button:

 Short press reset button into learning mode, then the sensor can inclusion or

exclusion from the Z-Wave network.

 Hold the key for 5s to reset the sensor, after reset, Sensor will send

“Device_Reset_Locally” to the main controller and exclude from the Z-Wave
network when the Button is released, this procedure will reset the Sensor to
factory default.

 Short press button for 3 times then the sensor sending wake up notificati

on to gateway, and LED will fast blink when sending data, send over then the L

ED turn off..

Pet immune

80 lbs (36 kgs)

Mounting height

6.23 ft. to 7.55 ft.

(1.9m to 2.3m)

Light sensor

20 lux for day/night(bright/dark)

Protocol

Z-Wave

Frequency

908.42MHz (US)

868.42MHz(EU)

Power source

Battery-powered

Battery type

CR123A X 1

Battery life

3 years

Anti-Tamper

YES

Low power alarm

YES

Certifications

CE/FCC/Z-Wave

3. Features/Capabilities:

 Supports pet immunity up to 80 lbs (36 kgs)
 Use PIR & Fresnel lens technology
 Easy installation with bracket
 Low battery alarm
 Equipped with an anti-tamper switch that reports any tampering

4. Installation Position and Notes

1. Installation position should be chosen at the area which the bass-by will be across, try

to make the bass-by in the detection area as below.

Side view

Top view

2. Do avoid installation near air-conditioner, electric fans, refrigerators, ovens or other

places where temperature easy change.

3. In order not to affect the detecting result, there should be no object in front of the

produces lens.

4. Building (such as the wall) will shorten the distance of wireless communication.

5. This device can be mounted on the wall only, it cannot be installed on the ceiling.

5. Product Installation

Adding the device as accessories, install it according to the diagram below:

① Choose the installation location on the wall, fix the bracket by screw or 3M

adhesion tape on the wall.

② Take off the bracket in the back, and draw out the battery insulation sheet, then

assembly the bracket.

③ Assembly the main body to the bracket.

Trigger

Description

Power on

In the network: Send Battery report and Wake up notification, the LED
turn on within 1 second.

Not in the network: Only the LED will be slow blink 3 times.

SmartStart
Inclusion

Add the Motion Sensor into the Z-Wave network via SmartStart:

1.

Add your Motion Sensor device to the primary controller’s
SmartStart provisioning list (if you don’t know how to do this, refer
to its manual) by scanning your device’s QR code

2.

Power on the motion sensor again.

3.

The motion will send “Z-Wave protocol Command Class” frame to
start SmartStart Inclusion.

4.

Led will fast blink and solid for 2 seconds to indicate the inclusion is
successful, if inclusion failed, Led will off.

Short press
button three
time

Add the Motion Sensor into the Z-Wave network:

5.

Power on your Motion Sensor, and let your Z-Wave controller into
add/inclusion mode.

6.

3 consecutive clicks in 1.5 seconds, the Motion Sensor will send out
a node info security CC in command class list (Security inclusion),
the LED will be fast blink for 30 seconds.

7.

If the inclusion is successful, the LED will be turn on within 2 seconds.
If failed, LED will be turn off forever, and please repeat the steps in
above.

Remove Motion Sensor from a Z-Wave network:

1.

Power on your Motion Sensor, and let the Z-Wave primary controller
into remove mode.

2.

3 consecutive clicks in 1.5 second, the LED will be fast blink for 30
seconds.

3.

If Motion Sensor has been successfully removed from your Z-Wave
network, the LED will be turn on 2 seconds. If failed, LED will be
turn off forever, and please repeat the steps in above.

6. Product Usage

Function of Action Button:

6.1 All functions of each trigger:

Function Of Action

Short press
button one
time

In the network: Send Wake up notification, and LED will fast blink when
sending data, send over then the LED turn off.

Not In the network: NOP.

Press and hold
more than 5
seconds

Reset Motion Sensor to factory default.

1.

Triggering this action, in 5 seconds LED will be accelerate blink.
After 5 seconds, the LED will remain on until the key is released.

Motion Sensor will send “Device_Reset_Locally” to the main

controller and exclude from the Z-Wave network when the button is
released, this procedure will reset the sensor to factory default.

2.

Please use this procedure only when the network primary controller is
missing or otherwise inoperable.

3.

When not in the network, triggering this action, in 5 seconds LED will
be accelerate blink red. After 5 seconds, the LED will remain on red

until the key is released. this procedure will reset the sensor to
factory default.

Motion is
triggered

In the network: Send Notification report and Sensor multilevel report and
Basic set (Setup configuration parameter 0x0E to 0x01), and the LED will
be turn on 0.2 second.

Not in the network: Motion sensor is disable.

Tamper switch is
triggered

In the network: Send Notification report, and the LED will be turn on 0.2
second.

Not in the network: Tamper switch is disable.

6.2 Caution:

This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Hereby, Corporation declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU

6.3 Low voltage alarm to remind changing battery.

This product has low voltage detection reminder, when the battery voltage is in low
status, the detector will give out low battery signal to controller.

7. Attention

1. If need to clean the sensor, please use a soft cloth with a little alcohol to wipe it after

you cut off the power.

2. This product is just for indoor use.

3. Replace the battery timely on low battery warning to ensure the detector works

properly. Please remove the battery and safe keeping, if you don’t use this product for

a long time.

4. This device can be mounted on the wall only, it cannot be installed on the ceiling.

5. The reference range template of PIR detection is tested at the indoor temperature (the

range is 20℃～25℃)，the target of the test is 77kg±10kg weight and 1.71m±0.3m
height, the target of the test across movement speed is 4m/s±0.15m/s.

6. In order to prevent the PIR sensor’s abnormal fault, please don’t mounting and

operating sensor in the bellow conditions,

Firstly, product mounting should prevent installed in the air flow environment such as

in front of the door, window, heater, air conditioner and so on.
Secondly, the PIR detection area should not be shielded by other screen.
Thirdly, if the operating temperature range is out of the defined range of product

specification may result in some product faults, which is not in the technique

commitment of manufacturer.
Fourthly, this product has mot pet immunity function, so when some animals go

through in front of the product may trigger PIR function reported.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS

Command Class List

Non-Included Non-Secure

Included S0 Non-Secure

Node Info

COMMAND_CLASS_ZWAVEPLUS_INFO

COMMAND_CLASS_ZWAVEPLUS_INFO

Frame

COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO

COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_SECURITY

COMMAND_CLASS_TRANSPORT_SERVICE_V2

COMMAND_CLASS_SECURITY_2

COMMAND_CLASS_VERSION

COMMAND_CLASS_SUPERVISION

COMMAND_CLASS_MANUFACTURER_SPECIFIC

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_BATTERY

COMMAND_CLASS_SECURITY

COMMAND_CLASS_SECURITY_2

COMMAND_CLASS_NOTIFICATION_V3

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

COMMAND_CLASS_WAKE_UP

COMMAND_CLASS_SUPERVISION

COMMAND_CLASS_CONFIGURATION_V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Security

COMMAND_CLASS_VERSION

Command
Supported

COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_ASSOCIATION

Report

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Frame

COMMAND_CLASS_MANUFACTURER_SPECIFIC

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_BATTERY

COMMAND_CLASS_NOTIFICATION_V3

COMMAND_CLASS_WAKE_UP

COMMAND_CLASS_CONFIGURATION_V4

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Included S2 Non-Secure

Node Info

COMMAND_CLASS_ZWAVEPLUS_INFO

Frame

COMMAND_CLASS_TRANSPORT_SERVICE
COMMAND_CLASS_SECURITY

COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION

Security

COMMAND_CLASS_VERSION

Command
Supported

COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_ASSOCIATION

Report
Frame

COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MANUFACTURER_SPECIFIC

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_BATTERY

COMMAND_CLASS_NOTIFICATION_V3

COMMAND_CLASS_WAKE_UP

COMMAND_CLASS_CONFIGURATION_V4

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Association Command Class

Motion Sensor supports 2 association groups and max 5 nodes for each group.

Association Group Info Command Class
Association Group Info

Grouping identifier

Group Name

Profile MS

Profile LS

01

Lifeline

0x00

0x01

02

On/Off control

0x71

0x07

Group 1

Command List Support

Command Class

COMMAND_CLASS_NOTIFICATION_V8(0x71)

Command

NOTIFICATION_REPORT_V8(0x05)

Command Class

COMMAND_CLASS_BATTERY(0x80)

Command

BATTERY_REPORT(0x03)

Command Class

COMMAND_CLASS_DEVICE_RESET_LOCALLY(0x5A)

Command

DEVICE_RESET_LOCALLY_NOTIFICATION(0x01)

Command Class

COMMAND_CLASS_SENSOR_MULTILEVEL_V5(0x31)

Command

SENSOR_MULTILEVEL_REPORT(0x05)

Group 2

Command List Support

Command Class

COMMAND_CLASS_BASIC(0x20)

Command

BASIC_SET(0x01)

Notification Type

Notification Event

HOME_SECURITY (0x07)

(0x00) NO_EVENT

Association Group Command List

Notification Commands

(0x03) TAMPERING_COVERING_REMOVED

(0x08) MOTION_DETECTION_UNKNOWN_LOCATION

POWER_MANAGEMENT (0x08)
(0x0A) REPLACE_BATTERY_SOON

(0x0B) REPLACE_BATTERY_NOW

(0x00) NO_EVENT

LIGHET_ALARM(0x14)

(0x00) NO_EVENT

(0x01) LIGHETSENSOR_ALARM_DETECTED

7 6 5 4 3 2 1 0

Command Class = COMMAND_CLASS_CONFIGURATION

Command = CONFIGURATION_SET

Parameter Number

Default

Reserved

Size

Configuration Value 1(MSB)

Configuration Value 2

……

Configuration Value n(LSB)

Configuration Set Command Class
Command Format

Name

Info

Paramet

er

Number

Default

Value

Max

Value

Min

Value

Size

Rea

d-

only

Format

Altering

capabilit

ies

LowBatPrecent

LowBatAlarm

0x0A

(10)

10

(0x0A)

50

(0x32)

5

(0x05)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

Pironoff

PironoffSet

0x0C

(12) 1 (0X01)

1

(0X01)

0

(0X00)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

PirTimeout

PirTimeoutSet

0x0D

(13)

60

(0X3C)

15300

( 0x3BC

4)

05

(0x05)

2

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

BasicEnable

SendBasic

0x0E

(14) 0 (0X00)

1

(0X01)

0

(0X00)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

BasicReverse

BasicValue

0x0F

(15) 0 (0X00)

1

(0X01)

0

(0X00)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

PirSensitivity

PirSensitivitySet

0x10

(16) 9 (0X09)

10

(0X0A)

0

(0X00)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

PirPetImmunity

PirPetImmunitySet

0x11

(17) 0 (0X00)

1

(0X01)

0

(0X00)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

LightSensorSend

Type

LightSensorSendSet

0x12

(18) 1 (0X01)

3

(0X03)

1

(0X01)

1

NOT

Read-

only

UNSIGNED

_INTEGER

Will alters

capabilities

Parameter
Number

Description

0x0A (10)

Low battery power level of alarm threshold values: the
value range are 5~50 for percentage, the battery low

power level can setting 5%~50%.

5.4.1

Parameter Number Definitions (8 bit)

5.4.2

Parameter Number description

0x0C(12)

Enable/Disable the PIR
0 = Disable the PIR.

1 = Enable the PIR.

0x0D (13)

Setup the wait time of PIR for clear the motion.
Valid values: 0x05~0x3BC4

0x0E (14)

When the Motion Sensor is triggered, if this parameter is
0x01 then it will send Basic set command to group 1.

0 = Don't send.
1 = Send.

0x0F (15)

PIR triggers the correspondence between the value of
the Basic set and the PIR state.

-If this value is 0x00 :
PIR triggers send the basic set with 0xFF, PIR alarm
release send the basic set with 0x00.

-If this value is 0x01 :
PIR triggers send the basic set with 0x00, PIR alarm
release send the basic set with 0xFF.

Only support 0x00 and 0x01 values as valid value.

0x10 (16)

Motion detection sensitivity level is a value between 1
and 10. This value affects the amount of motion energy
required to generate a motion event and also affects the
detection range and angle.

1 = Lowest Motion Sensitivity
10 = Highest Motion Sensitivity

0x11 (17)

Enable/disable pet immunity mode. This feature is lens
dependent and detection range may be reduced
when Pet Immunity is enabled.

0 = Disable the pet immunity mode
1 = Enable the pet immunity mode

0x12 (18)

Configure lightsensor to upload data form
1=Upload lumens value.
2=Upload day or night(By notification).
3=Upload lumens and day/night .

Command

value

Sensor multilevel supported

Air temperature (bit 0),

Luminance (bit 2).

5.5 Sensor_Multilevel

13