Ledj SPECTRA PAR 7T3 User Manual

www.prolight.co.uk

Order code: LEDJ257

USER MANUAL

SPECTRA PAR 7T3

(IP 66)

Spectra Par 7T3 Safety

1.

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

INPUT VOLTAGE OF 100~240V

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this
equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Spectra Par 7T3 Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Do not expose to ammable sources or gases.

• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 100V-240V.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• Avoid direct eye exposure to the light source while the product is on.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer
for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

LED failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

2.

SPECTRA PAR 7T3

Introduction

Features

• 7 x 3W tri-colour LEDs

• Beam angle: 28 degrees

• 0-100% dimming and variable strobe

• DMX channels: 1, 3, 4, 5 or 6 selectable

• Static colour, colour fade, colour change, colour mix, auto, master/slave and DMX modes

• Optional I.R remote (LEDJ90A)

• 4 push button menu with LED display

• IP rated power in/out sockets

• IP rated 3-pin DMX in/out sockets

• Power consumption: 35W

• Power supply: 100-240V~50/60Hz

• IP rating: IP-66

• Dimensions: 125 x 156 x 180mm

• Weight: 1.6Kgs

Overview

Setup

Operating Instructions

The Spectra Par 7T3 Exterior is a DMX-512 controllable unit made up of high efciency RGB
LEDs and will operate in stand alone, master/slave or DMX control modes.

Identication:
1, Mounting bracket
2, Power in/out lead
3, Mode button
4, Enter Button
5, Up Button
6, Down Button
7, DMX in/out lead
8, LED display
9, IR receiver

Spectra Par 7T3 Introduction

3.

Lux chart:

0 (M)

RGB

3740

28˚ - Lux

1155 446 341 187

1

2 3

4 5

Spectra Par 7T3 Operation Modes

Operation modes

Colour mix mode:

To activate the units colour mix mode, press the “M” button to show “COLr” on the LED screen.
Now press the “E” button to scroll through the three separate colours, red green and blue. To adjust

the brightness of each individual colour use the “UP” and “DOWN” buttons.

The “r” represents Red, “9.” = Green and B = Blue

The 3 digits after it are the brightness 000 to 255. Note: 000 = Off, 255 = Full on.

Examples:

If you set r, 9. and b to 000, the Spectra Par 7T3 will have no LEDs on (blackout).
If you set r to 255 and 9. and b to 000, the Spectra Par 7T3 will be 100% Red.

Built-in programmes:
To activate the units built-in programmes, press the “M” button to show “Pr01” on the LED screen.

Now use the “UP” and “DOWN” buttons to scroll through the built-in programmes from Pr01
to Pr07. Now tap the “E” button to select the desired speed and adjust by using the “UP” and

“DOWN” buttons. Press the “E” button once more to select the desired ash value and adjust by
using the “UP” and “DOWN” buttons.

Speed values: SP00 - SP99 (00 = slow, 99 = fast),
Flash values: FS00 - FS99 (00 = slow, 99 = fast)

In “Pr01” you can set a specic static colour. When in P.01, Press the “E” button and use the “UP”
and “DOWN” buttons to scroll through the list of built-in static colours.

0 = White (RGB) 1 = Red 2 = Orange 3 = Light Yellow 4 = Green 5 = Cyan
6 = Blue 7 = Purple 8 = Pink 9 = Yellow 10, Cool white 11, Warm white

To add strobe Press the “E” button again and use the “UP” and “DOWN” buttons to set strobe

from FS00 to FS99. To conrm your setting press the “ENTER” button.
Note: FS00 = slow, FS99 = fast.

Auto run mode

To activate the units auto run mode, press the “M” button to show “AUTO”
on the LED screen. The unit will now run through its built-in programmes.

DMX Mode

To activate the units DMX mode, press the “M” button to show “d001” on the LED screen and use
the “UP” and “DOWN” buttons to set the rst digit in the DMX address from 0 to 512.

To choose one of the 5 DMX channels, press the “E” button and use the “UP” and “DOWN”
buttons to scroll through the 1, 3, 4, 5 and 6 channel options.

To conrm your choice, press the “E” button.
For DMX functions, please see the DMX charts below.

4.