Ledgo LG-G260 Instruction Sheet

Instruction Sheet

LG -G 26 0

▲Notic e: This ma nual con tains im portant info rmation on how t o insta ll and use s afely. Ple ase read

caref ully and i nstal l accord ingly a s requir ed. Plea se keep this man ual pro perly in c ase you n eed it.

Zhang lin Sect ion, 324 H ighway, Dongli , Chengh ai, Shan tou, Guangdo ng, China

LEDGO Technology Limited

http://www.ledgo.hk

LEDG O TECHN OLOGY LIM ITED

Add:Z hangl in Secti on,Hi ghway 324,Do ngli, Cheng hai,Sh antou C ity,Guan gdong P rovinc e,Chi na

Tel:[phone] Fax:[phone]

E-mai l:inf o@ledg o.hk ht tp:// www.ledg o.hk

260W LED RGB STUDIO LIGHT

18

Main Technical Parameters

85. 8cm

61.3c m

1

1

1

1

48V

2

3.4

4

5

5

6

7

7

7.8

9.1 0.11.1 2

13. 14.15 .16

17

18

4

15cm

CONTENTS

Standard Configuration

·The following standard configurations are packed with the fixture, please check：

Ite ms

Power c able

Power Ada pter

Fligh t Case( witho ut whee ls)

Qua ntity

Uni t

Rem arks

PC

PC

PC

·Security Warning Info ...... .......... .......... .......... .......... ..................... .........

Structure & I nstallatio n .......... .......... ............................... .......... .......... ...

Power Conne ction ...... .......... .......... ............................... .......... .......... ....

Control Sig nal Connecti on ......... .......... .......... ............................... .........

DMX Loop Inse rt ......... .......... .......... ..................... .......... .......... .......... ...

Control Pan el Functiona l Buttons .... .......... .......... ............................... ...

DMX Start Address S etting ..... .......... .......... ............................... .......... ..

2.4G Remote C ontrol ..... .......... .......... ............................... .......... ..........

Master / Slav e Sync Mode .... .......... .......... ............................... .......... ....

Operation M enu ........ .......... .......... ............................... .......... .......... .....

DMX Control C hannel ..... .......... .......... ............................... .......... ........

General Bre akdown Analysis .. .......... .......... .......... ............................... .

Main Technical Paramet ers ........ ............................... .......... .......... ........

·

· ......... .......... .......... ...................

·

·

·

·

·

·

·

·

·

·

·

Install & Dis assemble of th e Barn doors

◆

should stri ctly follow th e warnings and o perating ins tructions st ated in this man ual, and
any damage ca used by misuse o r the neglect of t he operating m anual is not wit hin the
warranty of t he distribut ors and manufa cturer.

·If any change i n technology p arameters, shall take rea l product as cri terion witho ut notice.

This produc t is in good condi tion and packa ge is complete d while in the fac tory. All users

Input p ower: 48V DC 5. 8A, 100 -240V AC
Maxim um powe r:260 W

1) Inte rnati onal st andar d signa l:DMX 512 , 5-c ore DMX 512 int erfac e

(exte rnal wi ring) 1 0 contr ol chan nels

2) Mast er/Sl ave Syn c Mode

3) 2.4G M ode

4) WiFi APP Lighting Control Mode

Optic al Para meter s:

Color t emper ature : 2700K -7500 K
CRI (Ra ): 95

Weigh t: 11 KGS
Size: s hown bl ow

Contr ol Mode :

Power Ada pter: 2 .5Kg Ba rn door C ompon ents: 2 .5Kg

17

2

General Breakdown Analysis

Descr iptio n of Brea kdown

Mea surem ents

The fixture cannot light up normally

1) Please check if there is any loose connection between the
adapter and power cords or lighting socket.

2) Please check if the adapter voltage is within the specified
range.

3) If an external battery is used, please check if the battery is
in place.Please check if the battery voltage is the same as
the specified voltage.

The fixture can light up normally,
but cannot control with the controller

1) Check whether the DMX original address setting of the
fixture is correct or not.

2) Check that the XLR signal cable is connected correctly
or damaged.

LCD screen display garbled

Please turn off the fixture for 5-10 seconds and turn it on again.

The fan inside the fixture
does not work

1) Please check if the fan is set to the off state manually;

2) Please check if the dust plugs the fan or the vent.

Lighting brightness decreases
significantly

Please check if the fan is set to be manual off.

Barn doors cannot be removed

Please check if 4 screws on the corner of the protection
angle are completely released.

Please contact the local distributor or manufacturer for maintenance service if the faulty
problems are still not solved after taking the breakdown analysis and exclusion as above.

Security Warning Info

·While receiving the fixture, please check the lights if there is any external damage due to
transportation. Do not use the fixture if there is any external damage caused by shipping,
and please contact the dealer or manufacturer as soon as possible.

·Please do not place the fixture in the vicinity of solvents such as alcohol or gasoline, or other
common combustible materials.

·Qualified professionals and technical personnel are required to install, operate and maintain
the fixture and ensure that they are strictly in accordance with the procedures described in
the operating instructions.

·The fixture should be installed in a well-ventilated area, and check if the fan and vents are
unobstructed or not.

·Do not stare at the light source for a long time to avoid damaging the eyes!

·Please do not open the fixture to repair on your own.

·Operators who perform electric connections must have the appropriate qualifications.

·Before installation, make sure that the power supply voltage you are using matches the

voltage marked on the fixture.

·Do not use power cords with damaged insulation layer, and do not overlap the power cord
with other wires. When the fixture is not working or needs to clean, please unplug the power
cord, and pay attention not to drag the power cord directly for pulling out the plug.

·The temperature of the outer surface can reach 50°C when the fixture is used for a long time.
Please be careful not to be scalded.

·If you have any questions or suggestions, please contact the distributors or manufacturer
in time.

Notice:Before making any electric installation, repair and cleaning of the fixture, make sure
that the power has been cut off.

16

8

CCT

HSI

RGBW

000 -255

000 -255

9

CCT

HSI

000 -255

005 -255

000 -004

10

CCT

HSI

RGBW

Tungsten

Sodium Vepo ur

Metal Ha lide

Fluore scent

Street

Fla shing

OFF

Fla shing :0.1 -16S

SOS

000 -010

011- 110

111- 210

211- 255

000 -010

011- 110

111- 210

211- 255

3

Structure & Installation

Lighting modes

Fil ters

Lighting modes

Lighting modes

G: Gr een mix ed light ing

W: Whit e mixed l ighti ng

B: Gr een mix ed ligh ting

Cyc le OFF

Cyc le Time: 4 -16S

Fla shing

Fre q: 0-10 0

OFF

Fla shing :0.1 -16S

SOS

Fre q: 0-10 0

Gradually change from dark to bright

Gradually change from dark to bright

Gradually change from dark to bright

3 mod es swit ch

3 mod es swit ch

8.Barndoor Fixed Screws

9.Barndoor Subassembly

1.Control Interface

2.Sony V-lock

Battery Adapter

3.U-Bracket

Fixed Screws/U-Bracket

Mounting Screws

4.Stainless Steel Handle

5.Protection Angle

6.U-bracket

7.Anti-stripping ring

L32 02

L32 03

L32 04

L32 08

L32 16

L34 07

L34 11

L34 08

L34 09

L34 18

15

Sto rm

Candle L ight

Soft Dis co

Hard Dis co

Monito r

Multi Fl ash

Cop C ar

SPD

Cop S ingle

Cop D ouble

Cop Q uint_ Al l

Cop Q uint

Cop Q uad

Cop C ycle

Warm er

Coo lerl

Neu tra

000 -042

043 -084

085 -126

127 -168

169 -210

211- 25 5

000 -085

086 -172

173 -255

000 -255

000 -032

033 -064

065 -096

097 -128

129 -160

161 -192

193 -224

225 -255

000 -085

086 -172

173 -255

000 -127

128 -255

SAT

Col ors3

Col ors6

Col ors9

Col ors12

Col ors15

Col ors18

Col ors21

Col ors24

Warm er

Coo lerl

Neu tra

Mod ern

Blu e

7

CCT

HSI

RGBW

Tungsten

Sto rm

Candle L ight

Soft Dis co

Hard Dis co

Cop C ar

Monito r

Multi Fl ash

000 -255

000 -127

128 -255

000 -255

000 -255

Power Connection

4

The fixture can be installed directly on the light stand, is also suitable for hanging installation.

If you choose the hanging installation, please purchase the Quick installation components of
safety rope and installed it in four protection-angle hole of the fixture, please confirm if the
installation of light is reliable and stable on the required hanging position, please make sure
that the position has sufficient strength to support the fixture. For safety, the safety rope must
be used passing through the U-Bracket to assist the lifting and ensure the safety.

Notice:

The safety rope is only used when lifting the fixture. Do not use them as a handle tool to

carry the lights.

2.For safety, please ensure each safety rope can bear 25KG weight.

1.

Install & Disassemble of the Barn doors

·When installing the fixture, fasten the fixture with a vertically upwards, insert the barn doors
component from the top to the bottom, then tighten the four fixing screws in a clockwise
direction.

·When disassembling, fasten the fixture with a vertically upwards, turn it counterclockwise to
release the four fixing screws, slide the barn doors component out.

▲Notice: When installing and removing the barn doors component, please do not touch the
filter of the front panel to avoid getting surface scratches.

1.When connecting the power supply,please note that the supply voltage and frequency should
match the one marked on the power adapter.

2.When connecting an external battery or using the V-lock battery,please turn off the light first
before plugging or unplugging the power cords or battery.
▲Notice:

1.Use only the power cords and power adapter delivered with the fixture or suggested by the
manufacturer as an option.

2.The power plug on the adapter and the socket on the fixture should be connected as shown
below.

Pin1+: Connect the positive side of the power supply
Pin1- : Connect the negative side of the power supply

Special Effects

Special Effects

Lighting modes

R: Green mixed lighting

B: Green mixed lighting

B+: Green compensation

Pau se

Sta rt

Swi tch-f lashi ng mode

Sel ectin g modes

3 kin ds of lig ht sour ce swit ch

6 mod es swit ch

3 kin ds of lig ht sour ce swit ch

Gradually change from shallow to deep

8 kinds of light source modes switch

5

120 Ω

2

3

PIN 1 PIN 2

Pin 1:G ND(SCR EEN)
Pin 2:S ignal( -)
Pin 3:S ignal( +)
Pin 4:N /C
Pin 5:N /C

Pin 1:G ND(SCR EEN)
Pin 2:S ignal( -)
Pin 3:S ignal( +)

Pin 1:G ND(SCR EEN)
Pin 2:S ignal( -)
Pin 3:S ignal( +)
Pin 4:N /C
Pin 5:N /C

Pin 1:G ND(SCR EEN)
Pin 2:S ignal( -)
Pin 3:S ignal( +)

14

6

CCT

HSI

RGBW

Tungsten

Sodium Vepo ur

Metal Ha lide

Fluore scent

Street

Sodium Vepo ur

Metal Ha lide

Fluore scent

Street

Warm er

Coo lerl

Neu tra

YW

WW

NW

CW

Sto rm

Candle L ight

Soft Dis co

Hard Dis co

Monito r

Multi Fl ash

Cop C ar

000 -085

086 -172

173 -255

000 -063

064 -127

128 -191

192 -255

Fre q

B

RB

BW

RBW

SPD

SPD

SPD

SPD

Fre q

320 0K

560 0K

000 -127

128 -255

000 -255

000 -063

064 -127

128 -191

192 -255

000 -255
000 -255
000 -255
000 -255
000 -255

DMX IN

DMX OUT

1 GND

2 DATA-

3 DATA+

MS+

MS-

MS+

MS-

1

GND 1

DATA- 2

DATA+ 3

·The connection between the fixture and the console, and the fixtures between each one must
use a 4-core shielded conducting wire with a diameter of not less than 0.5 mm.The connection
between the XLR plug / socket and the conducting wire is shown above.

·Pin1, Pin2, Pin3 for connecting the DMX signal, Pin4, Pin5 for connecting the Master / Slave
signal of the fixture.
▲Notice: When the socket is connected, the internal pin cannot touch the inner case, and the
Pin and Pin can not touch each other. This fixture receives the international standard
control signal：DMX512 (1990) .

·5-core and 3-core XLR plug / socket switch
The fixture uses a 5-core XLR plug. If you are using a 3-core plug, please refer to the following
illustration.

▲Notice: When using a 3-pin XLR plug, the Master / Slave Mode Control cannot achieve.

Power Connection

DMX Loop Insert

DMX Circuit connection

Connect a 120 Ω(OHM) resistor

between the 2-pin and 3-pin XLR

plug and plug it into the DMX output

socket of the last fixture.

In the "DMX control mode", the DMX output port of the last fixture must be connected to the

DMX circuit plug (optional accessories). There is a resistance of about 120Ω (OHM) between
the 2-pin and 3-pin of this circuit plug (shown below). This circuit is inserted in the output of

the last fixture, which can effectively avoid the noise and reflection of the DMX512 signal
during transmission.

Lighting modes

Fil ters

Special Effects

Select the light source effects

Select the light source effects

GN: Red and green compensation

SAT

G: Green mixed lighting

G+: Green compensation

2 mod es swit ch

The frequency changes from slow to fast

Switch B / RB / BW / RBW 4 modes

Gradually change from fast to slow

Gradually change from fast to slow

Gradually change from fast to slow

Gradually change from fast to slow

The frequency changes from slow to fast

(-50)-(+50) Color compensation adjustment

Gradually change from shallow to deep

Gradually change from dark to bright

Gradually change from dark to bright

5 Pin Socket

3 Pin Plug 3 Pin Plug

5 Pin Socket

L32 02

L32 03

L32 04

L32 08

L32 16

L34 07

L34 11

L34 08

L34 09

L34 18

6

1

2

3

1

000 -255
000 -028

029 -056

057 -084

085 -112

113- 140

141 -168

169 -196

197 -224

225 -255
000 -031

032 -062

063 -093

094 -124

125 -155

156 -186

187 -217

218 -255
000 -023

024 -046

047 -069

070 -092

093 -115

116- 138

139 -161

162 -184

185 -207

208 -230

231 -255

2

13

3

4

Spe cial Ef fect

Lig hting M ode

Fil ters

OFF

CCT

HSI

RGB W

Tung sten

Sod ium Vepou r

Met al Hali de

Flu oresc ent

Str eet

OFF

Sto rm

Cop C ar

Can dle Lig ht

Sof t Disco

Har d Disco

Mon itor

Mul ti Flas h

OFF

5

CCT

HSI

RGBW

Tungsten

270 0K-7 500K

0- 360 °

000 -255

000 -255
000 -255
000 -255

Control Panel Functional Buttons

1.CCT Button:Press it which can switch the CCT Dimming Mode according to your demands.
Rotate the No.1 knob for adjusting the brightness;
Rotate the No.2 knob for adjusting the color temperature;
Rotate the No.3 knob for adjusting the RGB color compensation.

2.Color Trimming Button:Press it which can switch directly into the RGB color trimming mode,
the user can do color trimming based on the original mode according to your demands:

The No.1 knob is for the Red color trimming mode;
The No.2 knob is for the Green color trimming mode;
The No.3 knob is for the Blue color trimming mode.

3.RGBW Button:Press it which can switch the RGBW Dimming Mode,Rotate the Intensity Knob
for adjusting the lighting brightness; Press the Selector Knob can select the R/G/B/W color
mode then can rotate the No.2 knob for adjusting the color mix.

4.Menu Button:Press it which can display the menu operating mode on the LCD screen.

5.Filters Button:Press it which can switch the filters modes.Rotating the Intensity Knob can select
the filter color; Rotate the No.3 Knob can select the color temperature 3200K OR 5600K and
entering to get different filter effects.

6.Special Effects Button:Press it which can switch the Special Effects Mode.Rotating the Intensity
Knob can choose what special effect you need, then set the relevant parameters with rapid
simulation of a variety of special scene lighting effects.

7.Scenes Button:Press it which can switch the Scenes Mode to extract or save the customized
scenes.

8.Back Button:Press it which can operate the LCD Screen menu displaying return to the previous
level interface.

LG- G260 RG B studi o light h as a tota l of 10 con trol ch ann els, ca n recei ve th e DMX 512
int ernat ional s tanda rd sign al, and i ts resp ect ive con trol ch ann el co ntent a s follo ws

DMX Control Channel

Cha nnel Con tents

DMX Val ue

Des cript ions

Gradually change from dark to bright

Lig hting m ode

Gradually change from dark to bright

Gradually change from dark to bright

DIM ( D immer )

Lighting color temperature adjustment

Lighting color selection

Red mixed lighting

R+: Red compensation

L32 02

L32 03

L32 04

L32 08

L32 16

L34 07

L34 11

L34 08

L34 09

L34 18

12

7.Co mbine d

Con trol Mo ed

8. Add ress

9. Fan

ON

OFF

10. Ver sio n

Versi on

X.X X.XX

7

·

receive the dimmer signal and response correctly. This product has a total of 10 channels,
set the first fixture's DMX start address is set to 001, 011 for the second one displays, 021
for the third one displays, 031 for the fourth one displays, and so on.

·Press the Menu Button, LCD screen displays menu options, rotate the Selector Knob to
select "Address" and press the knob to confirm, enter the DMX address code settings page,
rotate the Selector Knob to set the fixture address code, stop your choosing then the system
will save the default Display automatically(the upper right corner of the format for the Ch: XXX).
Press the Back Button for exiting the settings interface.
▲Note: This DMX address code is equivalent to a wireless or WiFi address code when LEDGO
wireless remote control or LEDGO WiFi lighting control is enabled.

When using the console to control the fixture, each one must be set its DMX address, to

DMX Start Address Setting

WiFi 2.4G Remote Control

·The LG-G260 can be remotely operated with a 2.4G remote control or Wi-Fi APP lighting
control system.
Notice: The 2.4G remote control or Wi-Fi APP lighting control system should be bought
additionally ( regarding the detailed operating instructions, please refer to the
accessories manual).

·If you need to connect multiple fixtures to the master / slave sync mode, first connect the XLR
control cable from the DMX output port of the first fixture to the DMX input port of the second
fixture, and connect the DMX output port of the second fixture to the DMX input port of the
third fixture, and so on, until all the fixture are connected.

·Operation control panel MENU button, press the Selector knob which can switch the
Combined Control Mode option, rotate the Selector knob and press selecting the desired
mode, select the Master mode in the random preset host lights, and set the Slaver mode in
the slave machine, which achieves the Master / Slave Sync Mode control, at this point the
slave operating mode is the same as the host one. That is, it can be controlled through the
lighting of a host fixture to control the entire group of fixture's lighting

·In Master / Slave Sync mode, if the slave does not want to be controlled by the host, you can
set the combined control mode of the fixture in OFF mode.

Master/Slave Sync Mode

Combined Control Moed

OFF

Master
Slaver

Rotate the Selector Knob
for selecting Combined
Control Mode.

ADD RESS

512

Rotate the Selector Knob
for selecting the Address.

Fan setting instructions: When
you choose to the OFF mode,
the fixture output brightness
is 50%;When you choose to the
ON mode, the fixture output
brightness is 100%;When the
battery holder is equipped with
two batteries, the fan
automatically enters the OFF
mode

Rotate the Selector Knob
for selecting to turn
ON/OFF the Fan.

Display the fixture
version number

8

11

OFF
250mS
500mS

1000mS
2000mS

SOS

Flash-User Defined

Ch:001

6.0S

Flash-Random Blink

Ch:001

Freq:100%

5. Fla shing

6. Cyc le

OFF

4S

8S
12S
16S

User Defined

Cycle-User Defined

Ch:001

16.0S

SAVE

SCEN E-1

SCEN E-2

SCEN E-3

SCEN E-4

SCEN E-5

Do you save

the scene?

NO

YES

Extract ion

SCENE-1

SCENE-2

SCENE-3

SCENE-4

SCENE-5

Do you

the scene?

NO

YES

extract

4.Sc enes

▲Note:1. Fixture default DMX control priority, if the fixture connected to the DMX dimming
console, only can be controlled by the console and cannot be operated the Master /
Slave Sync mode.

2. When setting the master / slave mode, there is only one host fixture among all
connected fixtures , cannot set two or more than two hosts at the same time.

Slave

Master

Slave

Input Output Input Output Input Output

Scene-Save operation
instructions: used to save the
current settings scene, pressing
the Scenes Button can enter the
Scene Save Mode, save
customized scene according to
the display contents.

Scene-Extraction operation
instructions: used to extract
five kinds of scenes, pressing
the Scenes Button can enter
the Scene Extraction Mode,
extract customized scene
according to the display
contents.

Save

Used to extract the

user-defined scenes or

lighting effects, five

kinds of scenes are

available.

Extraction

Used to extract the
user-defined scenes
or lighting effects,
five kinds of scenes

are available.

Rotate the selector knob to
select the duration of the
flashing or turn it off.

User-Defined

For customizing the
duration of flashing.

Random Blink

For customizing the

frequency of the flashing.

Rotate the Selector Knob
or adjusting the color
retention time or turn
off the loop function.

For customizing the
Cycle Time.

10

L3202 Ch:001

DIM:100%

3200K 5600K

OFF

Cop Car Ch:001

DIM:100%

Color:RBW

Mode:Single

Caneld Light Ch:001

DIM:100%

SPD:100%

Mode:Single

Soft Disco Ch:001

DIM:100%

SPD:100%

SAT:100%

Hard Disco Ch:001

DIM:100%

SPD:100%

Colors:24

Monitor Ch:001

DIM:100%

SPD:100%

Mode:warmer

Multi Flash Ch:001

DIM:100%

Freq:100%

Mode:Modern

3.Special Effect

Storm Ch:001

DIM:100%

Freq:100%

SPD:100%

9

Mode:CCT Ch:001

DIM:100%

CCT:5600K

GN:+00

R:0% G:0% B:0%

Mode:HSI Ch:001

DIM:100%

HSI:360°

SAT:100%

Mode:RGBW Ch:001

DIM:100%

R:100% G:100%

B:100% R:100%

Tungs ten

Sod ium Vepou r

Met al Hali de

Mode:Tungsten Ch:001

DIM:100%

R:0% G:0% B:0%

Sodium Vepout Ch:001

DIM:100%

Metal Halide Ch:001

DIM:100%

Fluorescent Ch:001

DIM:100%

Warmer Cooler

Neutral

Mode:Street Ch:001

DIM:100%

YW WW

NW CW

Operation Menu

Pow er On dis pla ys LEDG O...

In the CCT operation interface,
if you want to add R.G.B color
trimming function, you can
press the Color Trimming
button on the panel to operate
and add the color according to
the display contents, press the
Scenes key can save the current
scene, the fixture enters the
Scene Save Mode, you can
extract or save the user-defined
scene according to the displayed
contents.

1.Lighting Modes

In the Tungsten operation
interface, if you want to add
R.G.B color trimming function,
press the Color Trimming Button
on the panel to operate and add
the color according to the display
contents, press the Scenes key
can save the current scene, the
fixture enters the Scene Save
Mode, you can extract or save
the user-defined scene according
to the displayed content.

Instructions

th

4 Men u

rd

3 ME NU

nd

2 Menu

Press the Selector knob to enter.

st

1 Menu

Press the Selector knob to enter.

CCT

Displays the light
brightness & color

temperature.Rotate

the Selector Knob

for adjusting the R/G

compensation.

HSI

Displays the light

brightness.Rotate the

Selector Knob for

adjusting the intensity

of the lighting color.

RGBW

Displays the brightness

percentage of the RGBW.

Fluorescent

Rotate the Selector Knob

for selecting 3 lighting

effects on the menu.

Street

Rotate the Selector Knob

for selecting 4 lighting

effects on the menu.

2.F ilter s

OFF
L3202
L3203
L3204
L3208
L3216
L3407
L3411
L3408
L3409
L3418

Rotate the Selector Knob
for selecting 10 kinds of
filters effect or turn off it.

Rotate the Selector Knob
for selecting two lighting
color temperature effects

Storm

Enter the menu to set the

brightness, frequency and

amplitude,press the Selector

Knob for adjusting the start

or the pause.

Cop Car

Enter the menu to set the

brightness, rotate the

Selector Knob for

selecting the modes.

Candle light

Enter the menu for

adjusting the brightness,

speed and mode.

Hard Disco

Enter the menu for

adjusting the brightness,

speed and saturation.

Soft Disco

Enter the menu for

adjusting the brightness,

speed and color type.

Monitor

Enter the menu for

adjusting the brightness,

speed and color type.

Multi Flash

Enter the menu for

adjusting the brightness,

frequency and mode.