Underbody Kit Includes:
(2) 36 Inch tubes (A)
(2) 48 Inch Tubes (B)
(1) Control Box
(1) 4 Button Wireless Remote
(1) Underbody Tube Junction Box
(14) Underbody Tube Brackets
(25) Zip Ties
(30) Large Screws
(2, 4, or 6) 15 Inch Interior Tubes (if you purchased add on interior tubes)
(1) Interior Tube Junction Box (if your purchased add on interior tubes)
Warning: If the tubes are not installed correctly the
lighting patterns will not display properly.
Note: The rear 36 inch LED tube has an 18 foot cable so
that you have no issue running it to the control box. Be sure
that this tube is mounted to the rear of your vehicle or you
will have problems later on in the installation.
4pc – 10pc Single Color Underbody Kit
Warning: Please check your state and local laws before installing this LED underbody lighting kit. Every state has different policies and procedures in place regarding
aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this underbody kit. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.
The control box that is used to power this lighting kit must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s
controller to fail. Any water damage or corrosion to this part will VOID all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED UNDERBODY KIT.
Underbody Installation
1. Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing. If you are installing interior tubes as well, mock them up
where you plan on installing them to ensure proper illumination.
2. Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with the installation. Simply connect the red
wire to the positive terminal and the black wire to any good ground source. Power the kit on to ensure full functionality. Once you have determined the kit is
functioning properly, remove the power from your kit.
3. Optional: Raise and support the vehicle.
4. Before mounting the each tube, please refer to the schematic below to ensure correct placement and tube direction.
5. Once the kit is laid out properly and you have determined that it is functioning properly, you can proceed with the rest of the installation.
6. First, mount the front tube, with the 13 foot lead wire facing the passenger’s side, to your vehicle using the included mounting brackets and zip ties. Make sure
the tube is at least 8 inches away from any direct heat source and away from all moving parts. Use the included wire ties to secure the underbody tube to the
mounting bracket. IMPORTANT: DO NOT DRILL ANY HOLES OR ATTACH THE MOUNTING BRACKETS TO THE RADIATOR.
7. Second, mount the driver’s side tube, with the power wire facing the rear of your vehicle, to your vehicle using the included mounting brackets and zip ties. A
good mounting location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not
mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power
wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.
8. Next, mount the passenger’s side tube, with the power wire facing the rear of your vehicle, to your vehicle using the included mounting brackets and zip ties. A
good mounting location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not
mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power
wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.
9. Now, mount the rear tube, with the 18 foot power wire facing the driver’s side, to your vehicle using the included mounting brackets and zip ties. Be extremely
aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the
exhaust and the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included wire ties to secure the underbody tube to
the mounting bracket.
12. Connect the black wire to a good, unpainted ground source. A couple of good ground sources are under the dash at any main bracket or grounding block, the
13. Beginning with the rear tube, run the power wire to the location of the junction box. Make sure to secure the wires tightly when going around the suspension
14. It is imperative to make sure that the wires are not mounted to any direct heat source or to any moving parts. Any excess length on the tube power wire will
15. DO NOT SHORTEN OR CUT ANY OF THE UNDERBODY TUBE POWER WIRES. This will destroy the kit and void all warranties.
16. Lower the vehicle if it was raised, power on and test the underbody kit for full functionality.
17. Once the vehicle is on the ground, turn the steering wheel as far as it can go in both directions to ensure the tubes and/or wires are not coming in contact with
Optional Interior Add On Tube Installation
1. Once your underbody kit is installed you can start installing your optional interior lighting tubes.
2. Connect the interior tube junction box, the box with 6 ports, to the port on the control box that is labeled “Light 2”
3. Depending on which kit your purchased will determine tube placement, but you can install these interior tubes anywhere you would like. We recommend either
4. Once you have determined the mounting location for your interior tubes, clean any dirt, oil, dust, or cleaning product from the surface using an alcohol prep pad.
5. Using the included 3M tape and screws mount the interior tube clips to your mounting location and snap the interior tubes into the clips. If you are unable to
6. Once you are done mounting all of your interior tubes, run the lead power wire from each tube to the interior tube junction box. Be sure to keep the lead wires
Sound Mode
1. There are two ways that your kit can pick up sound to have it react to the music playing inside of your vehicle:
or 16 gauge automotive grade wire. If you are running the power wire
to the battery, it must go through the firewall by using an existing
negative post on your battery, or any engine ground.
part and/or exhaust. Leave at least 8 inches between the exhaust and the underbody tube. If a power wire is pinched, the kit may malfunction and the warranty
could be voided. Run the rear tube’s power wire along one of the side tubes and make sure it is tightly secured. Next, run both side tubes power wires to the
junction box, then lastly run the front tube’s power wire to the junction box.
have to be bound up and secured tightly.
your tires or any other moving parts. If a tube or wire is damaged by the tire and/or any moving parts the warranty will be voided.
under your dashboard, under your front seats, under the rear seats, or even in your trunk.
Warning: The interior tubes are only intended to be installed to the interior of your vehicle, and are not water resistant. Mounting these tubes outside
of the vehicle could cause water damage, and will void LEDGlow’s warranty.
Warning: Do not shorten or cut the lead power wires on the interior tubes, this will destroy the kit and void the warranty.
mount the tubes to a flat location using the clips, mount the tubes using the included zip ties.
away from any moving parts, for example, the pedals, steering column, and/or seat tracks.
a. Connect the music and light sensor to your control box. Place the sensor close to your speaker to allow it to pick up the vibration.
b. Connect the control box directly to your head unit using the output source wire.
10. Find a safe, secure, and dry place to mount the underbody
tube junction box. We recommend mounting the junction box
inside of the car, if possible. If this is not possible, we suggest
mounting the junction box under the hood in the driest location
available. The junction box is not designed to be mounted under
the hood, and all warranties will be voided if the junction box
fails due to improper installation or because of water damage.
Optional: For extra protection, apply a thin bead of silicone
along the seams of the junction box to seal it.
11. Mount the underbody kit’s control box in a safe and secure
location inside of your vehicle. Connect the underbody tube junction
box’s distributor cable to the control box. If the junction box is
mounted under your hood, run the lead wire through a pre-existing
hole with a grommet in your firewall and to the control box. If you
do not have a pre-existing hole in the firewall you can drill one, just
be sure to use a rubber grommet to ensure the lead wire is not cut or
pinched.
This underbody kit can be powered one of two ways.
a. Connect the red power wire to any 12 volt
source. If you need to extend the power wires, be sure to only use 14
grommet or by drilling a hole and adding a new grommet which is
available at any auto parts store. Be sure to install a fuse within 6
inches of the power source. (You will have to install and
additional fuse if you have to extend the wires.) If you connect the
power wire to a switched 12 volt source, the underbody kit may not
remember the color and pattern it was last on before turning off the
vehicle. If you connect the power wire to a constant 12 volt source,
the underbody kit will remember the last color and pattern it was on
prior to turning the vehicle off. Do not run the wire through the
door jam, the wire can be pinched and will void all warranties.
b. This underbody kit can also be powered
directly from your vehicle’s fuse box. If you are powering the kit via
the fuse box, LEDGlow recommends that you install the wire using
LEDGlow’s Add-a-Circuit which is available on
LEDUnderbody.com.
Power Button
Pressing this button on the control box or wireless remote will turn your kit on and
off.
Speed Change Button
Pressing this button on the control box or
wireless remote will allow you to select from 5
different speeds for your selected pattern.
If your kit is in music mode, this button will
adjust the sensitivity of the selected music mode.
Mode Button
Pressing this button on the control box or wireless remote allows you to
change the current pattern displayed on your kit. There are 12 distinct
patterns, as well as 5 unique music modes. The patterns are listed below:
Solid Illumination Mode
Flashing Mode
Flashing Front Chase
Flashing Back Chase
Steady Front Chase
Steady Back Chase
Front Running Chase Mode
Back Running Chase Mode
Outside to Inside Flash
Inside to Outside Flash
Flash Pattern
Flash Pattern
(5) Sound Activation Modes
Color Change Button
This button is not used with LEDGlow’s Single
Color LED Underbody Kit.
Adding or replacing your wireless remote
1. The included wireless remote is already pre-programmed. This setup is only needed when replacing an existing remote or by adding additional remotes to your
2. In order to program the remote to the control box you must turn the kit off.
system. You may program up to 3 remotes to each control box.
a. First Remote - Press and hold the mode button on the remote and the mode control box on the control box for 5-7 seconds. Test the operation with the
remote.
b. Second Remote - Press and hold the mode button on the remote and the mode control box on the control box for 5-7 seconds. Test the operation with the
remote.
c. Third Remote - Press and hold the mode button on the remote and the mode control box on the control box for 5-7 seconds. Test the operation with the
remote.
Once you have installed your LED lighting kit, power the kit on using the 4 button wireless remote or the buttons located on the control box to
ensure that it is fully functional.
Using the Control Box & 4 Button Wireless Remote
For accessories, replacement parts and/or technical support please visit www.LEDGlow.com for more information.
LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from
defects in material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed incorrectly, or (2)
damaged by collisions, vandalism, other accidents, or similar causes.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to be
defective. After the warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our website,
www.LEDGlow.com, to determine the warranty coverage in the countries in which they are located.
LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals. Improper
installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s warranty does not
cover any expenses incurred in removing Products that are defective or re-installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for customers in
the contiguous United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product must be returned in its
original carton or in a similar package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight prepaid, to the Purchaser.
LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time.
This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the
Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is in its original
packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP, WRITTEN NOTICE
WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY
PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS
SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY
PERIOD. THE SPECIFIC WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR REPLACEMENT
OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER.
2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR) ALL LABOR NECESSARY TO
REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW
WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER'S FAILURE TO MAKE A CLAIM
AS PROVIDED IN PARAGRAPH 1 ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY
PURCHASER OF ALL CLAIMS THERETO.
3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO ANY OF
THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN THE USER'S
MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL,
OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S ORIGINAL IDENTIFICATION
(TRADEMARK, SERIAL NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS SOLD AS IS
AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND BATTERIES.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any
documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any
Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF
INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF
THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH
CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY
OTHER REASON WHATSOEVER.
GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws
principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.
This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full determination of
rights.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER
TERMS AND CONDITIONS
DISCLAIMER OF WARRANTY
LIMITATION OF LIABILITY
Loading...