(2) 48 Inch Tubes
(2) 36 Inch Tubes
(2) 24 Inch Tubes
(1) ON/OFF Switch
(16) Underbody Tube Brackets
(20) Zip Ties
(18) Large Screws
Self-Sealing Tape
Single Color Slimline Truck Underbody Kit
Warning: Please check your state and local laws before installing this truck LED underbody kit. Every state has different policies and
procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this
underbody kit. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void
all warranties.
The power switch that is used to power the underbody tubes must be installed in a dry location! Having this part exposed to water or the
elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will void all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED
UNDERBODY KIT.
Underbody Kit Installation:
1. Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing.
2. Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with the
installation. Simply connect the red wire to the positive terminal of the battery and the black wire to the negative terminal of the
battery or to any good ground source. Power the kit and once you have determined it is functioning properly, remove power from
the kit.
3. Before mounting the underbody tubes, please refer to the schematic below. The underbody tubes on this kit must be
installed in a specific way.
4. Once the kit is laid out and you have determined the kit is functioning properly, you can proceed with the rest of the installation.
5. Note: Each underbody tube daisy chains to the next tube with the included 6 feet of power wire and modular connectors. Use the
6. Optional: Raise and support the vehicle.
7. First, mount the front 36 inch tube to your vehicle with the male connector facing the driver’s side, using the included mounting
waterproof tape on all connectors to ensure connections are not exposed to the elements.
brackets and zip ties. Make sure the tube is at least 8 inches away from any direct heat source and away from all moving parts.
Use the included zip ties to secure the underbody tube to the mounting bracket. IMPORTANT: DO NOT MOUNT THE TUBE TO THE RADIATOR.
Page 2
8. Next, mount the driver’s side 48 inch tube towards the front of your vehicle using the included mounting brackets and zip ties.
Make sure to leave space towards the rear of the truck for the 24 inch tube for the driver’s side. A good mounting location for
this tube is either to the pinch well or side skirt. Be extremely aware of the location of the brake lines and fuel lines and do
not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody
tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the underbody tube
to the mounting bracket.
9. Now, mount the driver’s side 24 inch tube towards the rear of the truck, behind the already mounted 48 inch tube. A good
mounting location for this tube is either the pinch well or the side skirt. Be extremely aware of the location of brake lines and
fuel lines and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and
the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the
underbody tube to the mounting bracket.
10. Next, mount the rear 36 inch tube to the vehicle using the included mounting brackets and zip ties. Be extremely aware of the
location of brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust. Leave at least 8
inches between the exhaust and the underbody tube. Keep the tube and power wire away from any moving parts. Use the
included zip ties to secure the underbody tube to the mounting bracket.
11. Then, mount the passenger’s side 48 inch tube towards the front of the vehicle using the included mounting brackets and zip ties.
Make sure to leave space towards the rear truck for the 24 inch tube. A good mounting location for this tube is either to the pinch
well or side skirt. Be extremely aware of the location of the brake lines and fuel lines and do not mount the underbody
tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the
power wire away from any moving parts. Use the included zip ties to secure the underbody tube to the mounting bracket.
12. Next, mount the passenger’s side 24 inch tube towards the rear of the truck, behind the already mounted 48 inch tube. A good
mounting location for this tube is either the pinch well or the side skirt. Be extremely aware of the location of brake lines and
fuel lines and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and
the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included zip ties to secure the
underbody tube to the mounting bracket.
13. Mount the underbody kit’s ON/OFF switch in a safe and secure location inside of your vehicle. Run the lead power wire from
the front underbody tube through a pre-existing hole with a grommet in your firewall to the power switch. If you do not have a
pre-existing hole in your firewall, you can drill one, but just be sure to add a rubber grommet to ensure the lead wire is not cut or
pinched.
14. This underbody kit’s ON/OFF power switch can be powered one of two ways: Connect the red power wire to any 12 volt source. If you need to extend the power wires, be sure to only use 16 or 18
gauge automotive grade wire. If you are running the power wire to the battery, it must go through the firewall by using an
existing grommet or by drilling a hole and adding a new grommet, which is available at any auto parts store. Be sure to
install a fuse within 6 inches of the power source.
This underbody kit can also be powered directly from your vehicle’s fuse box. If you are powering the kit via the fuse box,
we recommend using LEDGlow’s Expandable Circuit, which is available at www.LEDGlow.com
15. Connect the black wire to a good, unpainted metal surface. A few good ground sources can be found under the dash at any main
bracket or grounding block, the negative terminal of your battery or any engine ground.
16. Beginning with Tube A, connect each tube to the next by using the modular connectors. Make sure to secure the wires tightly
when going around the suspension and/or exhaust. Leave at least 8 inches between the exhaust and underbody tube.
17. Once all of your connections have been made, and you have tested the kit to ensure all connections are secure, seal each
connection by using the included self-sealing. This ensures the connections will not get wet and cause your kit to fail.
18. It is imperative to make sure that the wires are not mounted to any direct heat source or to any moving parts. Any excess length
on the tube power wire will have to be bound up and secured tightly with zip ties.
19. DO NOT SHORTEN OR CUT ANY OF THE UNDERBODY TUBE WIRES. THIS WILL DESTROY THE KIT AND
VOID ALL WARRANTIES.
20. Lower the vehicle if it was raised, power the kit and test it for full functionality.
21. Once the vehicle is on the ground, turn the steering wheel as far as it can go in both directions to ensure the tubes and/or wires
are not coming in contact with your tires or any other moving parts.
For accessories, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.
Page 3
LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from defects in
material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed incorrectly, or (2) damaged by collisions,
vandalism, other accidents, or similar causes.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to be defective. After the
warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our website, www.LEDGlow.com, to
determine the warranty coverage in the countries in which they are located.
LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals. Improper installation may
cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s warranty does not cover any expenses incurred in
removing Products that are defective or re-installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for customers in the contiguous
United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product must be returned in its original carton or in a similar
package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight prepaid, to the Purchaser. LEDGlow does not provide Purchasers with temporary
replacement units during the warranty period or at any other time.
This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the Product is installed.
An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is in its original packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP, WRITTEN
NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL WARRCANTY CLAIMS MUST BE MADE WITHIN
THE WARRANTY PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF
RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE
ORIGINAL WARRANTY PERIOD. THE SPECIFIC WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING
THE REPAIR OR REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER.
2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR) ALL LABOR
NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR
DEFECTIVE PARTS. LEDGLOW WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT.
PURCHASER'S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED
ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER OF ALL CLAIMS THERETO.
3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO
ANY OF THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN
THE USER'S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NONQUALIFIED PERSONNEL, OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S
ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY
COVERAGE PRODUCTS SOLD AS IS AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS
FUSES AND BATTERIES.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise
in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of
any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE
PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws
principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.
This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full
determination of rights.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER
TERMS AND CONDITIONS
DISCLAIMER OF WARRANTY
LIMITATION OF LIABILITY
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.