LEDGlow Single Color Slimline LED Underbody Kit User Manual

Underbody Kit Includes:

 (2) 36 Inch tubes (A & C)
 (2) 48 Inch Tubes (B & D)
 (1) On/Off Switch

 (12) Underbody Tube Brackets
 (20) Zip Ties
 (12) Large Screws
 (1) Self Sealing Tape

Note: Each underbody tube daisy chains to the next
with the included 6 feet of power wire and modular
connectors.

Note: Use the waterproof tape on all connectors to
ensure connections are not exposed to the elements.

Single Color Slimline Underbody Kit

Warning: Please check your state and local laws before installing this LED underbody lighting kit. Every state has different policies and procedures in place regarding aftermarket vehicle accessories.

LEDGlow is not responsible for any fines that you may receive while using this underbody kit. This kit is for off road use only.

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.

The included on/off switch that is used to power this lighting kit must be installed in a dry location! Having this part exposed to water or the elements will cause the kit’s controller to fa il.
Any water damage or corrosion to this part will VOID all warranties.

PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED UNDERBODY KIT.

Underbody Installation

1. Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing.

2. Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with the installation. Simply connect the red wire to the positive

terminal and the black wire to any good ground source. Power the kit on to ensure full functionality. Once you have determined the kit is functioning properly, remove the power
from your kit.

3. Optional: Raise and support the vehicle.

4. Before mounting each tube, please refer to the schematic below to ensure correct placement and tube direction.

5. Once the kit is laid out properly and you have determined that it is functioning properly, you can proceed with the rest of the installation.

6. First, mount the front tube to your vehicle, with the male connector facing the passenger side, using the included mounting brackets and zip ties. Make sure the tube is at least 8 inches

away from any direct heat source and away from all moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket. IMPORTANT: DO NOT
DRILL ANY HOLES OR ATTACH THE MOUNTING BRACKETS TO THE RADIATOR.

7. Second, mount the driver’s side tube, with the male connector facing the rear of the vehicle, to your vehicle using the included mounting brackets and zip ties. A good mounting

location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to
the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included wire ties to
secure the underbody tube to the mounting bracket.

8. Next, mount the passenger’s side tube to your vehicle, with the male connector facing the rear of the vehicle, using the included mounting brackets and zip ties. A good mounting

location for this tube is either the pinch weld or side skirt. Be extremely aware of the location of brake lines and fuel lines, and do not mount the underbody tube too close to
the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube and the power wire away from any moving parts. Use the included wire ties to
secure the underbody tube to the mounting bracket.

9. Now, mount the rear tube to your vehicle, with the connector facing the rear of the vehicle, using the included mounting brackets and zip ties. Be extremely aware of the location of

brake lines and fuel lines, and do not mount the underbody tube too close to the exhaust. Leave at least 8 inches between the exhaust and the underbody tube. Keep the tube
and the power wire away from any moving parts. Use the included wire ties to secure the underbody tube to the mounting bracket.

10. Note: 3 brackets are provided for each tube, one for each end and an additional one for the middle of the tube. For a tight fit, you may want to place a very thin layer of the self sealing

tape on the end of each tube and secure the bracket around it to prevent any possible slippage while your vehicle is in motion.

11. Mount the underbody kit’s on/off switch in a safe and secure location inside of your vehicle. Run the lead power wire from the front underbody tube through a pre-existing hole with a

grommet in your firewall to the control box. If you do not have a pre-existing hole in the firewall you can drill one, just be sure to use a rubber grommet to ensure the lead wire is not
cut or pinched.

12. This underbody kit’s on/off switch can be powered one of two ways.

a. Connect the red power wire to any 12 volt source. If you need to extend the power wires, be sure to only use 14 or 16 gauge automotive grade wire. If you are running the

power wire to the battery, it must go through the firewall by using an existing grommet or by drilling a hole and adding a new grommet which is available at any auto parts store.
Be sure to install a fuse within 6 inches of the power source. (You will have to install an additional fuse if you have to extend the wires). Do not run the wire through the
door jam, the wire can be pinched and will void all warranties.

b. This underbody kit can also be powered directly from your vehicle’s fuse box. If you are powering the kit via the fuse box, LEDGlow recommends that you install the wire

13. Connect the black wire to a good, unpainted ground source. A couple of good ground sources are under the dash at any main bracket or grounding block, the negative post on your

14. Beginning with Tube A, connect each tube to the next using the modular connectors. Make sure to secure the wires tightly when going around the suspension part and/or exhaust.

using LEDGlow’s Add-a-Circuit which is available on LEDUnderbody.com.

battery, or any engine ground.

Leave at least 8 inches between the exhaust and the underbody tube. If a power wire is pinched, the kit may malfunction and the warranty could be voided. Run the rear tube’s power
wire along one of the side tubes and make sure it is tightly secured.

15. Once all of your connections have been made, and you have tested the kit to ensure all connections are good, seal each connection using the included

self-sealing tape. This ensures the connections will not get wet and cause your kit to fail.

16. It is imperative to make sure that the wires are not mounted to any direct heat source or to any moving parts. Any excess length on the tube power wire will have to be bound up and

secured tightly.

17. DO NOT SHORTEN OR CUT ANY OF THE UNDERBODY TUBE POWER WIRES. This will destroy the kit and void all warranties.

18. Lower the vehicle if it was raised, power on and test the underbody kit for full functionality.

19. Once the vehicle is on the ground, turn the steering wheel as far as it can go in both directions to ensure the tubes and/or wires are not coming in contact with your tires or any other

moving parts. If a tube or wire is damaged by the tire and/or any moving parts the warranty will be voided.

For accessories, replacement parts and/or technical support please visit www.LEDGlow.com for more information.

ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER

LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from defects in material or
workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed incorrectly, or (2) damaged by collisions, vandalism, other

accidents, or similar causes.

For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to be defective. After the warranty
period, the Purchaser must pay all charges for parts and labor.

Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our website, www.LEDGlow.com, to determine
the warranty coverage in the countries in which they are located.

LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals. Improper installation may cause
damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s warranty does not cover any expenses incurred in removing Products
that are defective or re-installing replacement Products in their place.

During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for customers in the contiguous United
States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product must be returned in its original carton or in a similar package affording an
equal degree of protection. LEDGlow will return the repaired or replaced Product, freight prepaid, to the Purchaser. LEDGlow does not provide Purchasers with temporary replacement units during the
warranty period or at any other time.

This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the Product is installed. An
“original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is in its original packaging and unopened.

This limited warranty is subject to all of the following terms and conditions:

1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP, WRITTEN NOTICE WITH AN
EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD, AND ANY
PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER
NOTIFICATION). THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY PERIOD. THE SPECIFIC WARRANTY ON THE
REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE
PRODUCT WARRANTY, WHICHEVER IS GREATER.

2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR) ALL LABOR NECESSARY TO REPAIR ANY
PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW WILL REFUND THE
PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER'S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1
ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER OF ALL CLAIMS THERETO.

3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO ANY OF THE
FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN THE USER'S MANUAL, FAILURE TO
FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL, OPERATION OF THE PRODUCT
OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL NUMBER) MARKINGS HAVE
BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS SOLD AS IS AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM
WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND BATTERIES.

All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or
license agreement furnished with the Product.

4. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any Product or of this
limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.

EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE
PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.

THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF THE LEGAL
THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO
EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws principles. The courts
of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.

This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full determination of rights.

TERMS AND CONDITIONS

DISCLAIMER OF WARRANTY

LIMITATION OF LIABILITY