LEDGlow Single Color LED Wheel Well Kit User Manual
Single Color LED Wheel Well Lighting Kit
Wheel Well Lighting Kit Includes:
(4) 24 Inch Flexible Tubes
(1) Control Box
(1) Junction Box
(30) Self Tapping Screws
(20) Zip-Ties
Warning: Please check your state and local laws before installing this Single Color LED Wheel Well Kit. Every state has different policies and
procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this
lighting kit. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all
warranties.
The Control Box and Junction Box that are used to power the wheel well tubes must be installed in a dry location! Having these parts
exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all
warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED
WHEEL WELL LIGHTING KIT.
Wheel Well Lighting Kit Installation:
1. Arrange the tubes out on the ground and test the kit to ensure proper functionality before installing. Please refer to the
schematic below for proper placement of the tubes, control box and junction box.
2. Optional: Raise and support the vehicle if necessary. Remove the vehicle’s wheels if necessary.
3. Start with the driver’s side tube and mount it with plenty of clearance from any heat sources, suspension and moving
parts. The flexible tube can be contoured and mounted on top of the wheel or behind the strut with the included selftapping screws.
4. Repeat Step #3 for the remaining 3 tubes. It is extremely important to ensure the tubes do not come into any contact
with any heat sources, suspension and/or moving parts.
5. If you removed the vehicle’s wheels, you can now reinstall them in accordance to factory specifications.
6. After the tubes have been mounted and the wheels have been reinstalled back in place, turn the steering wheel all the
way to the right and left several times to ensure the tubes do not come into any contact with the wheels or any other
moving parts. If there is clearance between the tubes and the wheels, you may resume the installation.
7. Find a safe, secure and dry location to mount the control box. The control box was not designed to withstand water or
the elements. We recommend mounting the control box inside of the vehicle and running the junction box through the
firewall.
8. Connect the red power wire to a positive (+) 12 volt source. If
you need to extend the red and black power wires, be sure to use 16 or 18
gauge automotive grade wiring. If you are running the wires to your
vehicle’s battery, it must go through the firewall by an existing grommet
or by drilling a hole and adding a new grommet which is available at any
auto parts store. Be sure to install the fuse within 6 inches of the battery. If
you connect the power wires to a switched source, the control box will not
remember the pattern the kit was last on. If you connect the power wires
to a constant source, the control box will remember the pattern the kit was
last on. Also when connected to a constant source, you will need to
physically turn the kit off as it will not power down with your vehicle. If
you want to tap power from your vehicle’s fuse box, we recommend using
LEDGlow’s Expandable Circuit which is available at
www.LEDGlow.com.
9. Connect the black wire to a good, unpainted metal surface under
the dash at any main bracket or grounding block. If you are connecting the
wires to your vehicle’s battery, connect the black wire to the negative (-)
terminal of the battery or any engine ground.
10. Next, mount the junction box on the firewall away from heat and in a dry location. The junction box was not designed
to withstand the elements. Corrosion to the junction box will void all warranties and may cause the kit to fail.
11. Starting with the rear wheel well tubes, run the wires to the location on the junction box. Connect the white stripe wire
of the tube to the (+) port on the junction box and the solid black wire to the (-) port on the junction box. Make sure to
secure the wires to any suspension parts by using the included zip ties. Leave at least 10 inches between the exhaust
and the wires.
12. Lower the vehicle if it was raised and test your new kit.
For accessories, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.
Loading...