6pc Million Color Pro SMD LED Expandable Motorcycle Kit
Million Color Pro Kit Includes:
(6) 6 Inch Flexible Tubes
(1) Control Box
(1) Wireless Remote
(6) Mini USB Connectors
3M Tape
Warning: Please check your state and local laws before installing this Motorcycle Lighting Kit. Every state has different policies
and procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may
receive while using this lighting kit. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this
kit will void all warranties.
It is imperative that all of the tubes are installed and connected to the control box with the included USB power wires
BEFORE powering and turning this kit on. Failure to follow these instructions will result in the control box failing.
The control box that is used to power the motorcycle lighting strips must be installed in a dry location! Having this part
exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will
VOID all warranties.
It is recommended to install each motorcycle lighting tube using 3M™ Adhesion Promoter which allows for a much stronger
bond between the adhesive tape of the light tube and the cleaned mounting surface of your motorcycle. This is an optional
installation accessory that is NOT included with your motorcycle lighting kit.
You do not need to close the daisy chain circuit in order for this kit to function fully.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING
THIS LED MOTORCYCLE KIT.
Motorcycle Light Kit Installation:
1. Upon receiving your new motorcycle lighting kit, we ask that you first test the kit to ensure it is functioning properly.
MAKE SURE TO CONNECT THE TUBES AND USB WIRES TO THE CONTROL BOX BEFORE
POWERING THE KIT ON. Connect the red power wire to the positive terminal of the battery and the black ground
wire to the negative terminal of the battery. Once the wires are temporarily secure, power the kit to ensure full
functionality before installing it. If everything appears to be working correctly turn the kit off and disconnect the power
and ground wires from the battery to prepare for installation.
2. Optional: Remove any trim pieces from your motorcycle that may hinder the installation of the lighting tubes.
3. Begin by first laying out the LED lighting tubes similar to the way they will be installed. Note: Each lighting tube is
linked to the next tube through the daisy chaining feature. It is extremely important to mount the first tube of the daisy
chain sequence as close to the control box location as the length of the USB wire you are using. Make sure that the
wires will be able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires
and tubes away from all moving parts that may come in contact with any part of the kit. A few recommended locations
on your motorcycle to mount the light tubes are under the gas tank, lower frame rail, rear fender frame rail, triple trees,
lower swing arm, and under the seat. IF A WIRE IS PINCHED, IT WILL CAUSE THE KIT TO
MALFUNCTION AND WILL VOID THE WARRANTY DUE TO PHYSICAL DAMAGE.
4. Once the motorcycle lighting tubes and wires have been mocked up, clean the proposed mounting surfaces with an
alcohol prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest
bonding results from the double sided adhesive tape. Note: The surface area must be free of all oils, moisture, dirt and
wax in order for the supplied adhesive tape to bond and adhere to the installation surface correctly. Recommended: To
achieve the strongest bond between the lighting strips and the motorcycle, you can use 3M Adhesion Promoter, which
is sold separately from your kit.
Red
Yellow
Ice Blue
Pink
Light Yellow
Light Blue
Purple
Bright Yellow
Lavender
Dark Purple
Green
Blue
Light Purple
Light Green
Soft White
Orange
Teal
White
5. Start by mounting the first tube to the motorcycle and measure where you plan to mount the next tube. Plug the USB
power wire into first tube and run the end of the USB wire to the planned location of the next tube. Be sure to keep all
wires and tubes away from any suspension and moving parts by using the provided 3M tape or zip ties (not included) to
hold the wires and tubes in place. Do not mount the tube too close to the exhaust. Leave at least 10 inches between
the exhaust and the tube.
6. Mount the remaining tubes to their desired locations and run the USB wires the same way as you did in Step #5. Plug
the USB power wires into the tubes and run the end of the wire to the location of the next closest tube in the circuit. Be
sure to keep all wires and tubes away from any suspension and moving parts by using the provided 3M tape or zip ties
(not included) to hold the wires and tubes in place. Note: You do not need to close the daisy chain circuit with the final
tube.
7. Find a secure and dry place to mount the control box. We recommend mounting it under the seat or in a water tight
compartment if possible. If this is not possible then we suggest mounting the control box in the driest location
available. The control box is not designed to withstand any water damage and if any does occur, it will void all
warranties.
8. Connect the red power wire from the control box to the positive terminal of the battery and the black ground wire to the
negative terminal of the battery.
9. Once again, make sure that the wires are not mounted to any part that will heat up or move. Any excess wire will have
to be bound up and secured tightly.
10. If any parts were removed for the light kit installation, you can now reinstall them and test your new kit.
11. Expandability: This Million Color Pro SMD Motorcycle Lighting Kit has the ability to be expanded to include up to
12 tubes for maximum brightness. Users can purchase Add-On Light Tubes directly from www.LEDGlow.com.
12. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.
Wireless Remote Functions:
1. Button A: Power ON/OFF (Press and Hold for 2-3 Seconds)
During operation, press the button once to pause the current color on the color changing mode. Press it again
to resume with the color changing mode.
2. Button B: Featured Modes / Patterns
Color Cycle Mode
Color Fading Mode
Solid Illumination Mode (Speed Function is NOT Available with this Mode)
18 Color Change Mode
Single Color Flashing Mode
18 Color Flashing Mode
SOS Flashing (Speed Function and Music Mode is NOT Available with this Mode)
Demo (Changes All Featured Patterns Every 15 Seconds)
3. Button C: Color Change Mode
4. Button D: Speed Function / Music Mode
5 Speed Levels
Music Mode
o Press and Hold “Button D” for 2-3 Seconds to Activate Music Mode (You Will Hear One Long
Tone)
o Press and Hold “Button D” for 2-3 Seconds to Deactivate Music Mode (You Will Hear Two Tones)
Reprogramming the Wireless Remote:
Turn the kit off. Press and hold down “Button A” on the wireless remote. While holding down “Button A” on the
wireless remote, press and hold “Button B” on the control box. You will hear one tone if synchronization was successful. If you
hear multiple tones, the synchronization did NOT work successfully. If synchronization was not successful, repeat the steps. If
you are still having problems synchronizing the wireless remote and control box, please contact our Technical Support
Department at 1.877.LED.Glow or by email at TechSupport@LEDGlow.com.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER
LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be
free from defects in material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed
incorrectly, or (2) damaged by collisions, vandalism, other accidents, or similar causes.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to
be defective. After the warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our
website, www.LEDGlow.com, to determine the warranty coverage in the countries in which they are located.
LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals.
Improper installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s
warranty does not cover any expenses incurred in removing Products that are defective or re-installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for
customers in the contiguous United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product
must be returned in its original carton or in a similar package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight
prepaid, to the Purchaser. LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time.
This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on
which the Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product tha t is in
its original packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR
WORKMANSHIP, WRITTEN NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL
WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN
ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE
REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY PERIOD. THE SPECIFIC
WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR
REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER.
2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY
FOR) ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW
OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR
OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER'S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR
CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER
OF ALL CLAIMS THERETO.
3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT
THAT IS SUBJECTED TO ANY OF THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW
THE OPERATING PROCEDURES OUTLINED IN THE USER'S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE
MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL, OPERATION OF THE PRODUCT OUTSIDE OF THE
PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL
NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS
SOLD AS IS AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS
FUSES AND BATTERIES.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty
eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE
PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws
principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.
This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full
determination of rights.
DISCLAIMER OF WARRANTY
LIMITATION OF LIABILITY
Loading...