LEDGlow Million Color Mini SMD Motorcycle Lighting Kit User Manual

6pc Million Color Mini SMD LED Expandable Motorcycle Kit

Million Color Mini Kit Includes:

 (6) 4 Inch Flexible Tubes  (1) Control Box  (1) Wireless Remote

 (6) Mini USB Connectors  3M Tape

Warning: Please check your state and local laws before installing this Motorcycle Lighting Kit. Every state has different policies and procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may receive while using this lighting kit. This kit is for off road use only.

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.

It is imperative that all of the tubes are installed and connected to the control box with the included USB power wires BEFORE powering and turning this kit on. Failure to follow these instructions will result in the control box failing.

The control box that is used to power the motorcycle lighting strips must be installed in a dry location! Having this part

exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will

VOID all warranties.

It is recommended to install each motorcycle lighting tube using 3M™ Adhesion Promoter which allows for a much stronger bond between the adhesive tape of the light tube and the cleaned mounting surface of your motorcycle. This is an optional installation accessory that is NOT included with your motorcycle lighting kit.

You do not need to close the daisy chain circuit in order for this kit to function fully.

PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED MOTORCYCLE KIT.

Motorcycle Light Kit Installation:

1. Upon receiving your new motorcycle lighting kit, we ask that you first test the kit to ensure it is functioning properly.

MAKE SURE TO CONNECT THE TUBES AND USB WIRES TO THE CONTROL BOX BEFORE POWERING THE KIT ON. Connect the red power wire to the positive terminal of the battery and the black ground

wire to the negative terminal of the battery. Once the wires are temporarily secure, power the kit to ensure full functionality before installing it. If everything appears to be working correctly turn the kit off and disconnect the power and ground wires from the battery to prepare for installation.

2. Optional: Remove any trim pieces from your motorcycle that may hinder the installation of the lighting tubes.

3. Begin by first laying out the mini LED lighting tubes similar to the way they will be installed. Note: Each lighting tube

is linked to the next tube through the daisy chaining feature. It is extremely important to mount the first tube of the daisy chain sequence as close to the control box location as the length of the USB wire you are using. Make sure that the wires will be able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and tubes away from all moving parts that may come in contact with any part of the kit. A few recommended locations on your motorcycle to mount the light tubes are under the gas tank, lower frame rail, rear fender frame rail, triple trees, lower swing arm, and under the seat. IF A WIRE IS PINCHED, IT WILL CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY DUE TO PHYSICAL DAMAGE.

4. Once the motorcycle lighting tubes and wires have been mocked up, clean the proposed mounting surfaces with an

alcohol prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest bonding results from the double sided adhesive tape. Note: The surface area must be free of all oils, moisture, dirt and wax in order for the supplied adhesive tape to bond and adhere to the installation surface correctly. Recommended: To achieve the strongest bond between the lighting strips and the motorcycle, you can use 3M Adhesion Promoter, which is sold separately from your kit.

Red

Yellow

Ice Blue

Pink

Light Yellow

Light Blue

Purple

Bright Yellow

Lavender

Dark Purple

Green

Blue

Light Purple

Light Green

Soft White

Orange

Teal

White

5. Start by mounting the first tube to the motorcycle and measure where you plan to mount the next tube. Plug the USB

power wire into first tube and run the end of the USB wire to the planned location of the next tube. Be sure to keep all wires and tubes away from any suspension and moving parts by using the provided 3M tape or zip ties (not included) to hold the wires and tubes in place. Do not mount the tube too close to the exhaust. Leave at least 10 inches between the exhaust and the tube.

6. Mount the remaining tubes to their desired locations and run the USB wires the same way as you did in Step #5. Plug

the USB power wires into the tubes and run the end of the wire to the location of the next closest tube in the circuit. Be sure to keep all wires and tubes away from any suspension and moving parts by using the provided 3M tape or zip ties (not included) to hold the wires and tubes in place. Note: You do not need to close the daisy chain circuit with the final tube.

7. Find a secure and dry place to mount the control box. We recommend mounting it under the seat or in a water tight

compartment if possible. If this is not possible then we suggest mounting the control box in the driest location available. The control box is not designed to withstand any water damage and if any does occur, it will void all warranties.

8. Connect the red power wire from the control box to the positive terminal of the battery and the black ground wire to the

negative terminal of the battery.

9. Once again, make sure that the wires are not mounted to any part that will heat up or move. Any excess wire will have

to be bound up and secured tightly.

10. If any parts were removed for the light kit installation, you can now reinstall them and test your new kit.

11. Expandability: This Million Color Mini SMD Motorcycle Lighting Kit has the ability to be expanded to include up to

24 tubes for maximum brightness. Users can purchase Add-On Light Tubes directly from www.LEDGlow.com.

12. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.

Wireless Remote Functions:

1. Button A: Power ON/OFF (Press and Hold for 2-3 Seconds)

 During operation, press the button once to pause the current color on the color changing mode. Press it again

to resume with the color changing mode.

2. Button B: Featured Modes / Patterns

 Color Cycle Mode  Color Fading Mode  Solid Illumination Mode (Speed Function is NOT Available with this Mode)  18 Color Change Mode  Single Color Flashing Mode  18 Color Flashing Mode  SOS Flashing (Speed Function and Music Mode is NOT Available with this Mode)  Demo (Changes All Featured Patterns Every 15 Seconds)

3. Button C: Color Change Mode

+ 2 hidden pages