LEDGlow Million Color Golf Cart Kit User Manual
Million Color LED Golf Cart Underbody Lighting Kit
Golf Cart Kit Includes:
(4) 24 Inch Flexible Tubes
(1) Control Box
(1) Junction Cable
(1) Wireless Remote
(30) Self Tapping Screws
(20) Zip-Ties
Warning: Please check your state and local laws before installing this Million Color LED Golf Cart Underbody Kit. Every state has different
policies and procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while
using this lighting kit. This kit is for off road use only.
Warning: THIS GOLF CART LIGHTING KIT WAS DESIGNED TO BE POWERED BY A 12 VOLT SYSTEM. IF YOU ARE
RUNNING A 36 OR 48 VOLT SYSTEM, A STEP DOWN TRANSFORMER IS REQUIRED.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all
warranties.
The Control Box and Junction Cable that are used to power the underbody tubes must be installed in a dry location! Having these parts
exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all
warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED
GOLF CART KIT.
Golf Cart Kit Installation:
1. Arrange the tubes out on the ground the way you plan on installing it and test the kit to ensure proper functionality before installing.
2. Temporarily power your kit with any 12 volt source to ensure it is functioning properly before you move forward with this installation.
Simply connect the red wire to the positive (+) terminal and the black wire to any good bare ground metal source or negative (-)
terminal of the battery. Power the kit on to ensure full functionality. Once you have determined the kit is functioning properly, remove
the power from your kit and begin the installation.
3. Optional: Raise and support the golf cart if necessary.
4. Before mounting each tube, please refer to the schematic below to ensure correct placement and tube direction.
5. Start with the front tube and mount it with plenty of clearance from heat and moving parts. The tube is flexible and can be contoured
incase the undercarriage is not flat. Make sure that the wires are routed away from any moving parts or exhaust. For gas powered golf
carts leave at least 10 inches between the exhaust and the tube. Also, be sure to keep all wires and tubes away from any steering
suspension parts. You can use the provided self-tapping screws and/or zip ties to hold the tubes in place. If you use the provided
screws, use zip ties to secure the tube.
6. Repeat Step #4 for the remaining 3 underbody tubes. It is very important to ensure that all of the wires do not come in contact with
any moving parts and/or heat sources.
7. Connect the red wire to a 12 volt source. If a 12 volt source is not available because you have a 36 or 48 volt system, then it is
required to use a step down transformer which is available at any electronic store. IF YOU ARE UNSURE, VERIFY VOLTAGE
WITH A MULTI-METER BEFORE CONNECTING THE KIT TO THE GOLF CART.
8. If you need to extend the power wires, be sure to use a 16 or 18 gauge automotive grade wire. If you are running the power wire to the
battery and must go through metal, use an existing grommet or drill a hole and add a new grommet, which is available at any auto
parts store. Be sure to reinstall the fuse within 6 inches of the power source. If you connect the power wire to a switched 12 volt
source, then it will not remember the previous color and pattern it was last on. If you are running the wire to the fuse block, LEDGlow
recommends that you install the wire using our Expandable Circuit, which is available online at www.LEDGlow.com or at any auto
parts store, as well.
9. Connect the black wire to a good ground source, grounding block or you can connect it directly to the negative terminal of the battery.
10. Next, mount the junction cable on the golf cart away from heat in a dry location. The junction cable must be mounted away from
moisture and the elements. CORROSION TO THE JUNCTION CABLE WILL VOID ALL WARRANTIES AND MAY
CAUSE CONTROLLER FAILURE.
11. Starting with the rear tubes, run the wires to the dry location of the junction cable. Make sure to secure the wires tightly when going
around any suspension parts and exhaust. Leave at least 10 inches between the exhaust and the wires. Also, be sure to keep all wires
and tubes away from any suspension parts. If a wire is pinched, the kit may malfunction and could void the warranty. Run the wires
along one side of the golf cart and make sure to tightly secure it. Then, run the front tube wires to the junction block.
12. Once again, make sure the wire is mounted away from heat and moving parts. Any excess wire will have to be bound and secured
tightly.
13. DO NOT SHORTEN OR CUT THE WIRES. YOU WILL DESTROY THE KIT AND VOID THE WARRANTY.
14. Lower the golf cart if it was raised, and test your new LEDGlow Million Color LED Golf Cart Underbody Kit.
15. With the golf cart on the ground, turn the steering wheel as far as it can go in both directions to ensure that there will be no tubes
and/or wires coming in contact with the tire as you’re driving down the road. If a tube or wire is damaged by the tire, the warranty
will be voided.
Adding or Replacing your Wireless Remote:
1. Your kit is already pre-programmed for the included wireless remote. This setup is only needed when replacing an existing remote or
by adding additional wireless remotes to your system. You can program up to 3 wireless remotes to one control box.
2. In order to program the remote to the control box, you must turn the kit off.
a) First Remote - Press and hold the mode button on the wireless remote and the mode button on the control box for 5-7
seconds. Test the operation with the remote.
b) Second Remote - Press and hold the mode button on the wireless remote and the mode button on the control box for 5-7
seconds. Test the operation with the remote.
c) Third Remote - Press and hold the mode button on the wireless remote and the mode button on the control box for 5-7
seconds. Test the operation with the remote.
For accessories, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.
Loading...