LEDGlow LiteTrike Advanced Million Color Wheel Well Kit User Manual
LiteTrike Advanced Million Color LED Wheel Well Lighting Kit
(2) 36” Wheel Well Strips
(1) Control Box
(1) Wireless Remote
(1) 2pc Wheel Well Harness
(2) Packets of 3M Adhesion
Promoter
Zip-Ties
Warning: Please check your state and local laws before installing this Trike Lighting Kit. Every state has different policies and
procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may
receive while using this lighting kit. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this
kit will void all warranties.
The control box that is used to power the lighting strips must be installed in a dry location! Having this part exposed to
water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all
warranties.
It is recommended to install each lighting strip using 3M™ Adhesion Promoter which allows for a much stronger bond between
the adhesive tape of the light strip and the cleaned mounting surface of your trike.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING
THIS LED TRIKE KIT.
LiteTrike Wheel Well Kit Includes:
LiteTrike Wheel Well Kit Installation:
1. Upon receiving your new LiteTrike Wheel Well Lighting Kit, we ask that you first test the kit to ensure it is functioning
properly. Connect the red power wire from the control box to the positive terminal of the battery and the black ground
wire to the negative terminal of the battery. Once the wires are temporarily secure, power the kit by pressing “Button
D” on the wireless remote to ensure full functionality before installing it. If everything appears to be working properly,
turn the kit off and disconnect the power and ground wires from the battery to prepare for installation.
2. Optional: Remove any trim pieces from your trike that may hinder the installation of the lighting strips.
3. Begin by first laying out the LED lighting strips similar to the way they will be installed. Make sure that the wires will
be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and strips away from
all moving parts that may come in contact with any part of the kit. IF A POWER WIRE IS CUT OR PINCHED, IT
WILL CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY DUE TO PHYSICAL
DAMAGE.
4. Temporarily place the lighting strips to their intended mounting locations and route the power wires to the planned
control box mounting area. Use the supplied zip ties to secure the power wires to their mounting points. Be sure to
keep the power wires away from the suspension, any direct heat sources and/or moving parts.
5. The lighting strips must be mounted to the designated wheel well areas as each strip features side mounting adhesion.
Install the right side wheel well strip to the right wheel well and the left side wheel well strip to the left wheel well. Run
the wires to the planned location of the control box and secure each wire to the frame by using the included zip ties. Be
sure to use the zip ties, this is a very important step that should not be skipped. Once this step is complete and the
lighting strips and wires are secure, allow ample time for the adhesive to settle and cure.
6. Find a secure and dry place to mount the control box. We recommend mounting it under the seat or in a water tight
compartment if possible. If this is not possible then we suggest mounting the control box in the driest location
available.
7. Connect the red power wire from the control box to the positive terminal of the battery. If the power wire needs to be
extended, be sure to use 16 or 18 gauge automotive grade wiring. Be sure to reinstall the fuse within 6 inches of the
battery. Connect the black ground wire to the negative terminal of the battery.
8. The kit was designed using a modular locking plug system for connecting the lighting strips to the control box by using
the included wire harness. Start plugging the male connections from the strips and control box into the female
connections of the harness.
9. Test the functionality of the kit once more. If everything seems to be working properly, you can now reinstall any trim
you removed for the installation.
10. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.
Wireless Remote Functions:
This kit provides multiple lighting patterns and several brightness levels, which are easily operated by using the
included wireless remote. The wireless remote features four buttons, “A, B, C, D”
Button A: Cycles through 15 solid colors, as well as a color cycle and color fade pattern.
Hold for 5 seconds to select brightness level when on a solid color.
Button B: Activates the strobing pattern when a single color is selected.
Hold to increase pattern speed when on a color cycle/color fade pattern.
Button C: Activates fading pattern when a single color is selected.
Hold to decrease pattern speed when on color cycle/color fade pattern.
Button D: Power On/Off
For accessories, add-on kits, replacement parts and/or Technical Support, please visit www.LEDGlow.com for more information.
Loading...