Home Theater Kit Includes:
(2) 15 Inch Tubes (A)
(2) 9 Inch Tubes (B)
(1) Control Box
(1) IR Remote
(1) Power Supply
(4) Mounting Brackets
(8) Small Screws
(6) Double Sided Tape
(1) IR Receiver
(2) Sealing Caps for Tubes
LED Home Theater Kit
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.
Warning: To reduce the risk of burns, fire, electrical shock, or injury to persons:
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED HOME THEATER KIT.
6. Now mount the first 15 inch tube to the top of your television. Remove the tape protector and firmly press each mounting clip to your installation surface.
7. Mount the second 9 inch tube to the right side of your television. Remove the tape protector and firmly press each mounting clip to your installation surface.
8. Mount the second 15 inch tube to the bottom of your television. Remove the tape protector and firmly press each mounting clip to your installation surface.
9. Starting with the left hand side tube, connect each tube to the next using the included mini USB power cables. The bottom tube should be the last tube
10. Mount the control box in a location where the last power cable can easily connect to it. This step is going to be unique to each installation based on how your
11. Once the control box is mounted, connect the last lead power cable to your control box.
12. Now connect the infrared (IR) receiver to the control box, and mount it in a location where it is free from any interference and has a clear line of sight.
13. Lastly, plug the included power supply into a standard wall outlet and connect the mini jack to the control box.
14. Now that your kit is installed and powered turn the kit on using the included remote and test the kit again for full functionality.
Unplug the kit from the outlet before installing or uninstalling any parts.
Close supervision is necessary when this product is used by, or near children, or anyone else who cannot be responsible for their own safety.
NOT intended for recessed installations.
NOT intended for surface installations inside built-in furnishings
Keep cord away from heated surfaces and from children
NEVER operate this kit if it has been damaged or dropped in water
Home Theater Kit Installation
1. Arrange the tubes on the ground and test the
kit to ensure proper functionality before moving forward with
the installation.
WARNING: Disconnect all power for
this kit before moving forward with the install. Reconnect
power to the kit after finishing all connections.
DO NOT connect or plug in any cable or tube while you
are installing this kit.
2. Once you know your kit is functioning
properly and have determined your mounting location, ensure
the installation surface is free of dust, dirt, oil, or any other
foreign objects that will not allow the included double sided
take to adhere properly.
NOTE: Rubbing alcohol or any type
of cleaning solution will work best, but be sure the solution
you are using will not affect the mounting surface.
3. Install the mounting clips to your installation
surface using the included double sided tape. Be aware that
over a long period of time this tape may cause some
discoloration to the mounting surface. Remove one side of
the tape protector to apply it to the bottom of the mounting
clip, apply pressure for 5 seconds to ensure proper adhesion.
Repeat this step for the other 3 clips.
4. Place the light bars in the clips by applying
light pressure to the back of the clip. DO NOT apply
pressure to the tube itself, this may cause damage to the tube.
5. Mount the first 9 inch tube to the left side of
your television. Remove the tape protector and firmly press
each mounting clip to your installation surface.
NOTE: The object of this installation is to install the lights so that the reflected light is visible and not the tubes. The tubes are installed using the
mounting clips so that you can swivel each tube to achieve the best lighting effect possible.
connected so that it can be easily connected to the control box.
television is mounted.
NOTE: The included IR receiver works together with the included remote to operate the kit, and allows you to keep your control box hidden.
NOTE: If your remote is not controlling the kit properly, you may need to adjust the IR receiver to achieve the best result.
Kit Operation and Using the IR Remote
Memory Function:
The memory function will only work
with solid color modes. Set the kit to
your desired solid color, press M then
either 1, 2, 3, or 4 and your color
option will be saved.
Color Adjustment:
Press to move forward through all
available color options. The cycle will take
20 seconds to complete.
Press to move backward through all
available color options. The cycle will take
20 seconds to complete.
Once the kit is in either of these modes,
press the pause button to stop the fade
mode. To slowly step between colors, press
to you reach your desired
color. Then follow the steps in the memory
function section to save your custom color!
Sleep Function:
The timer will power your kit down
after a certain amount of time. Press
the SLEEP button then 1, 2, 3, or 4 and
the power will turn off in 1, 2, 3, or 4
hours
Brightness Mode:
The brightness mode will only work when
the kit is set to a solid color. Press to
increase brightness and press to
decrease the brightness.
Turns the Kit On/Off
Speed Adjustment:
Adjusts the speed of fade mode, and will
adjust the sensitivity of the sound activation
modes.
Puts the kit into a Million Color Fade
Mode.
Puts the kit into a sound activated mode.
Colors vary according to intensity of the
sound.
Puts the kit into a fade mode. Press
again to pause on custom colors.
Factory Reset:
Pressing these buttons in succession will set
the kit back to factory defaults. If successful,
you will see all of the lights flash once.
LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from
defects in material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed incorrectly, or (2)
damaged by collisions, vandalism, other accidents, or similar causes.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to be
defective. After the warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our website,
www.LEDGlow.com, to determine the warranty coverage in the countries in which they are located.
LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals. Improper
installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s warranty does not
cover any expenses incurred in removing Products that are defective or re-installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for customers in
the contiguous United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product must be returned in its
original carton or in a similar package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight prepaid, to the Purchaser.
LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time.
This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the
Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is in its original
packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR WORKMANSHIP, WRITTEN NOTICE
WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY
PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS
SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY
PERIOD. THE SPECIFIC WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR REPLACEMENT
OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER.
2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR) ALL LABOR NECESSARY TO
REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW
WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER'S FAILURE TO MAKE A CLAIM
AS PROVIDED IN PARAGRAPH 1 ABOVE OR CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY
PURCHASER OF ALL CLAIMS THERETO.
3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS SUBJECTED TO ANY OF
THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE OPERATING PROCEDURES OUTLINED IN THE USER'S
MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL,
OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S ORIGINAL IDENTIFICATION
(TRADEMARK, SERIAL NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS SOLD AS IS
AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND BATTERIES.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any
documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any
Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF
INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF
THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH
CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY
OTHER REASON WHATSOEVER.
GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws
principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.
This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full determination of
rights.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER
TERMS AND CONDITIONS
DISCLAIMER OF WARRANTY
LIMITATION OF LIABILITY
Loading...