LEDGlow Flexible Million Color Motorcycle Lighting Kit User Manual

6pc Flexible Million Color LED Motorcycle Light Kit

Motorcycle Kit Includes:

 (6) Lighting Tubes
 (1) Control Box
 (1) Wireless Remote

 3M™ Tape

Warning: Please check your state and local laws before installing this Motorcycle Lighting Kit. Every state has different policies
and procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may
receive while using this lighting kit. This kit is for off road use only.

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this
kit will void all warranties.

The control box that is used to power the motorcycle lighting tubes must be installed in a dry location! Having this part

exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will

VOID all warranties.

It is recommended to install each motorcycle lighting strip using 3M™ Adhesion Promoter which allows for a much stronger
bond between the adhesive tape of the light strip and the cleaned mounting surface of your motorcycle. This is an optional
installation accessory that is NOT included with your motorcycle lighting kit.

PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING
THIS LED MOTORCYCLE KIT.

Motorcycle Kit Installation:

1. Upon receiving your new motorcycle lighting kit, we ask that you first test the kit to ensure it is functioning properly.

Connect the red power wire to the positive terminal of the battery and the black ground wire to the negative terminal of
the battery. Once the wires are temporarily secure, power the kit to ensure full functionality before installing it. If
everything appears to be working correctly, turn the kit off and disconnect the power and ground wires from the battery
to prepare for installation.

2. Optional: Remove any trim pieces from your motorcycle that may hinder the installation of the lighting tubes.

3. Begin by first laying out the LED lighting tubes similar to the way that they will be installed. Make sure that the wires

will be able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and
tubes away from all moving parts that may come in contact with any part of the kit. IF A POWER WIRE IS

PINCHED, IT WILL CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY DUE TO
PHYSICAL DAMAGE.

4. Temporarily place the motorcycle lighting tubes to their intended mounting locations and route the power wires to the

planned control box mounting area. Use zip ties to secure the power wires to their mounting points. Be sure to keep
the power wires away from the suspension, any direct heat sources and/or moving parts. A few recommended
locations on your motorcycle to mount the light tubes are under the gas tank, lower frame rail, rear fender frame rail,
triple trees, lower swing arm, and under the seat.

5. Once the motorcycle lighting tubes and wires have been mocked up, clean the proposed mounting surfaces with an

alcohol prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest
bonding results from the double sided 3M adhesive tape. Note: The surface area must be free of all oils, moisture, dirt
and wax in order for the supplied 3M adhesive tape to bond and adhere to the installation surface correctly.
Recommended: To achieve the strongest bond between the lighting tubes and the motorcycle, you can use 3M
Adhesive Promoter which is sold separately from your kit.

6. Mount each lighting strip to the cleaned and dry surface of the motorcycle by using the supplied 3M tape. Run the

wires to the planned location of the control box and secure the wire to the bike frame by using zip ties. Once this step is

complete and the lighting tubes and wires are secure, allow ample time for the adhesive to settle and cure. Repeat this
step for the remaining tubes included with your kit.

7. Find a secure and dry place to mount the control box. We recommend mounting it under the seat or in a water tight

compartment if possible. If this is not possible then we suggest mounting the control box in the driest place available.
The control box is not designed to withstand any water damage and if any does occur, it will void all warranties.

8. Connect the red power wire from the control box to the positive terminal of the battery. If the power wire needs to be

extended, be sure to use 16 or 18 gauge automotive grade wire. Be sure to reinstall a fuse within 6 inches of the battery.
Connect the black ground wire to the negative terminal of the battery.

9. Connect the male connections of the wires from the lighting tubes to the female ports of the control box. Secure the

excess wires of the tubes to the frame of your bike by using zip ties. DO NOT CUT OR SHORTEN ANY WIRES,

YOU WILL VOID THE WARRANTY.

10. If you removed any trim for this installation, you can now reinstall them and test the functionality of your kit by

pressing the on/off button on the wireless remote.

11. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.

Wireless Remote Functions:

This kit provides multiple colors, lighting patterns and several speed levels, which are easily operated using the

included wireless remote. The remote includes four buttons, “A, B, C, D”

Button A: Controls Color and Pattern Selections
Button B: Turns the Kit On/Off
Button C: Speed Up Lighting Pattern
Button D: Slows Down Lighting Pattern

Reprogramming the Wireless Remote:
To reprogram the wireless remote, you will simultaneously press and hold the button that’s located on top of the control

box as well as the “B” button on the wireless remote for 3-5 seconds. If the reprogramming was successful, your lighting kit will
flash the color green.

Troubleshooting:
If the kit or lights do not appear to operate, first check the installed inline mini fuse. If the fuse is blown, check the

wires on the entire kit to ensure they are not cut, pinched or scorched. If there is no damage to any of the wires and no water
damage is visible to the control box, replace the fuse and test the kit again. If the inline fuse is intact, clean both the positive and
negative terminals of the battery. Corrosion to the battery terminal can cause a poor connection or simulate being disconnected.

For accessories, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.