LEDGlow Flexible Million Color LED Interior Lighting Kit User Manual

Interior Kit Includes:

 (6) 8 Inch Tubes
 (1) Control Box
 (1) Wireless Remote

 (14) Screws
 (4) Mounting Brackets
 3M Tape

6pc Flexible Million Color LED Interior Kit

Warning: Please check your state and local laws before installing this LED interior lighting kit. Every state has different policies and

procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this
interior kit. This kit is for off road use only.

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all

warranties.

The control box that is used to power the interior tubes must be installed in a dry location! Having this part exposed to water or the
elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will VOID all warranties.

PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING THIS LED
INTERIOR KIT.

Interior Kit Installation:

1. Arrange the interior tubes where you plan on installing them and temporarily power the kit to ensure proper functionality before

installing. Once you test the kit and determine it is functioning properly, disconnect the power from the kit and begin the
installation.

2. Each interior tube can be mounted virtually anywhere in your vehicle. Some good locations are under the dash in the foot well

area, under the driver and passenger seats facing the foot well area, under the back of the driver and passenger seats facing the
back seat or even in the trunk.

3. Find a safe, secure, and dry location to

mount the control box. We recommend
mounting the control box in your center
console, under the seat or in your glove
compartment by using the included screws
or 3M tape.

4. Mount the first tube to your desired

location with the included screws. If you
do not want to use the supplied screws,
you can use 3M tape, wire ties, or even
Velcro. Make sure the tube and the lead
power wire do not come in contact with
any moving parts such as, the pedals,
steering column, and/or seat tracks.

5. Mount the remaining tubes to your desired

locations in the same way you did in the
previous step. Again, be sure all tubes and
lead power wires are not in the way of any
moving parts such as the pedals, steering
column, and/or seat tracks.

6. Connect the tubes to the control box that is

already installed in a readily accessible
area free of moisture and heat.

Any damage to your kit as a result of
moisture or heat will void your
warranty.

7. Now, that your control box and tubes are

mounted, secure and hide all of the lead
wires with zip ties.

8. This interior kit can be powered one of three ways:

 Solid Color On Mode

 Flash Pattern 2

 Scan Mode

 Flash Pattern 3

 Scan Mode 2

 Flash Pattern 4

 Scan Mode 3

 Color Fade Mode

 Flash Pattern

 Color Cycle Mode

 Red

 Light Green

 Green

 Light Blue

 Blue

 White

 Orange

 Light Yellow

 Yellow

 Ice Blue

 Purple

 Violet

 Fire Orange

 Cool White

 Aqua

 Connect the red power wire to any 12 volt source and the black wire to a bare metal ground source. If you need to extend

the power wires, be sure to only use 16 or 18 gauge automotive grade wire. If you are running the power wire to the
battery, it must go through the firewall by using an existing grommet or by drilling a hole and adding a new grommet,
which is available at any auto parts store. Be sure to install the fuse within 6 inches of the power source. If you connect the
power wire to a switched 12 volt source, the interior kit may not remember the color and pattern it was last on before
turning off the vehicle. If you connect the power wire to a constant 12 volt source, the interior kit will remember the last
color and pattern it was on prior to turning the vehicle off. Do not run the wire through the door jam, the wire can be
pinched and the will void all warranties.

 This interior kit can also be powered directly from your vehicle’s fuse box. If you are powering the kit via the fuse box,

LEDGlow recommends that you install the wire using LEDGlow’s Expandable Circuit which is available on

www.LEDGlow.com

 For a quick and easy install, LEDGlow offers a Cigarette Lighter Adapter that allows you to simply connect the red and

black wires to the attachment and plugging it into your cigarette lighter for power. This is available at

www.LEDGlow.com.

Wireless Remote Functions

 Button A: Color Change Mode & Pattern Changing Mode
 Colors Included:

 Modes/Patterns

 Button B: Power ON/OFF (Press and Hold for 3 Seconds)

 Button C: Speed Up Function
 Button D: Speed Down Function

 During Operation, press this button once to PAUSE the current color changing function. Press it a second time to

RESUME with the color changing function.

For accessories, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.