Single Color Motorcycle Lighting Kit w Dual Zone Control Box
Motorcycle Kit Includes:
Motorcycle LED Lighting
Strips
(1) Dual Zone Control Box
(1) Wireless Remote
Wire Harness
Zip-Ties
Warning: Please check your state and local laws before installing this kit. Every state has different policies and procedures for
aftermarket accessories. This kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this
kit will void all warranties.
The included Motorcycle Lighting Control Box must be installed in a dry location. Having the control box exposed to
water or the elements will cause it to fail. Any water damage or corrosion to this part will VOID all warranties.
PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS KIT.
Motorcycle Kit Installation:
1. Upon receiving your new motorcycle lighting kit, we ask that you first test the kit to ensure it is functioning properly.
Connect the red power wire to the positive terminal of the battery and the black ground wire to the negative terminal of
the battery. Once the wires are temporarily secure, power the kit to ensure full functionality before installing it. If
everything appears to be working correctly, turn the kit off and disconnect the power and ground wires from the battery
to prepare for installation.
2. Optional: Remove any trim pieces from your motorcycle that may hinder the installation of the lighting strips.
3. Begin by first laying out the LED lighting strips similar to the way they will be installed. Make sure that the wires will
be able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and strips
away from all moving parts that may come in contact with any part of the kit. IF A POWER WIRE IS PINCHED, IT
WILL CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY DUE TO PHYSICAL
DAMAGE.
4. Temporarily place the motorcycle lighting strips to their intended mounting locations and route the power wires to the
planned control box mounting area. Use the supplied zip ties to secure the power wires to their mounting points. Be
sure to keep the power wires away from the suspension, any direct heat sources and/or moving parts. A few
recommended locations on your motorcycle to mount the light strips are under the gas tank, lower frame rail, rear
fender frame rail, triple trees, lower swing arm, and under the seat.
5. Once the motorcycle lighting strips and wires have been mocked up, clean the proposed mounting surfaces with an
alcohol prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest
bonding results from the double sided adhesive tape. Note: The surface area must be free of all oils, moisture, dirt, and
wax in order for the supplied adhesive tape to bond and adhere to the installation surface correctly. Recommended: To
achieve the strongest bond between the lighting strips and the motorcycle, you can use 3M Adhesive Promoter, which
is sold separately from your kit.
6. Mount each lighting strip to the cleaned and dry surface of the motorcycle by using the supplied 3M tape. Run the
wires to the planned location of the control box and secure the wire to the bike frame by using the included zip ties. Be
sure to use the zip ties, this is a very important step and should be not skipped. Once this step is complete and the
lighting strips and wires are secure, allow ample time for the adhesive to settle and cure. Repeat this step for the
remaining strips included with your kit.
7. Find a secure and dry place to mount the dual zone control box. We recommend mounting it under the seat or in a
water tight compartment if possible. If this is not possible then we suggest mounting the control box in the driest place
available. The control box is not designed to withstand any water damage and if any does occur, it will void all
warranties. Optional: Seal the end caps of the control box with silicone to prevent water damage.
Button A:
1. Channel A- Illuminated, Channel B- Off
(Hold Button A- Dims Channel A from Levels
0-100)
2. Channel A- Off, Channel B- Illuminated
(Hold Button A- Dims Channel B from Levels
0-100)
3. Channel A & B- Illuminated at Same Time
(Hold Button A- Dims Both Channel A & B
from Levels 0-100)
4. Channel A- Solid On, Channel B- Fading
5. Channel A- Fading, Channel B- Solid On
6. Channel A- Flashing, Channel B- Solid On
7. Channel A- Solid On, Channel B- Flashing
Button B:
1. Channel A- Flashing
2. Channel B- Flashing
3. Channel A & B- Simultaneous Flashing
4. Channel A Flashes 3 Times then Channel B
Flashes 3 Times
5. Alternates Flashing Channel A to Channel B
Button C:
1. Channel A- Fading
2. Channel B- Fading
3. Channel A & B- Simultaneous Fading
4. Channel A- Fading, Channel B- Fading
5. Channel A- Fading, Channel B- Flashing
6. Channel A- Flashing, Channel B- Fading
Button D:
1. Turns Kit On/Off
8. Connect the red power wire from the dual zone control box to the positive terminal of the battery. If the power wire
needs to be extended, be sure to use 16 or 18 gauge automotive grade wire. Be sure to reinstall the fuse within 6 inches
of the battery. Connect the black ground wire to the negative terminal of the battery.
9. This dual zone control box features two lead wires coming from the control box. These lead wires allow you to connect
two separate wire harnesses for each zone of your bike. We recommend running the LED strips that are mounted to the
front of your bike to one harness and running the LED strips that are mounted to the back of your bike to the other
harness. This dual zone control box allows for full customization so you can illuminate your bike anyway you would
like such as one color to one zone and another color to the other zone.
10. The kit was designed using a modular locking plug system for connecting the motorcycle lighting strips to the control
box by using the included wire harness. Start plugging the male connections from the strips and control box into the
female connections of the harness. Secure the excess wires of the strips and harness to the frame of your bike using the
included zip ties. DO NOT CUT OR SHORTEN ANY WIRES, YOU WILL VOID THE WARRANTY.
11. If you removed any trim for this installation, you can now reinstall them and test the functionality of your kit by
pressing the on/off button on the wireless remote.
12. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.
4 Button Wireless Remote Functions:
This motorcycle lighting kit includes 18 different dual zone lighting modes and patterns, all of which are easily cycled
through with the wireless remote.
Troubleshooting:
If the kit or lights do not appear to operate, first check the installed inline mini fuse. If the fuse is blown, check the
wires on the entire kit to ensure they are not cut, pinched or scorched. If there is no damage to any of the wires and no
For accessories, add-on kits, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.
water damage is visible to the control box, replace the fuse and test the kit again. If the inline fuse is intact, clean both
the positive and negative terminals of the battery. Corrosion to the battery terminal can cause a poor connection or
simulate being disconnected.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER
LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be
free from defects in material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed
incorrectly, or (2) damaged by collisions, vandalism, other accidents, or similar causes.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to
be defective. After the warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our
website, www.LEDGlow.com, to determine the warranty coverage in the countries in which they are located.
LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals.
Improper installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s
warranty does not cover any expenses incurred in removing Products that are defective or re-installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for
customers in the contiguous United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product
must be returned in its original carton or in a similar package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight
prepaid, to the Purchaser. LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time.
This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on
which the Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is in
its original packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR
WORKMANSHIP, WRITTEN NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL
WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN
ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE
REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY PERIOD. THE SPECIFIC
WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR
REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER.
2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY
FOR) ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW
OR REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR
OR REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER'S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR
CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER
OF ALL CLAIMS THERETO.
3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT
THAT IS SUBJECTED TO ANY OF THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW
THE OPERATING PROCEDURES OUTLINED IN THE USER'S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE
MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL, OPERATION OF THE PRODUCT OUTSIDE OF THE
PUBLISHED ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL
NUMBER) MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS
SOLD AS IS AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS
FUSES AND BATTERIES.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty
eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE.
THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE
PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws
principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.
This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full
determination of rights.
DISCLAIMER OF WARRANTY
LIMITATION OF LIABILITY
Loading...