Motorcycle Kit Includes:
Motorcycle LED Lighting
Strips
(1) Power Switch
Wire Harness
Zip Ties
2-4pc Classic LED Motorcycle Light Kit
Warning: Please check your state and local laws before installing this Motorcycle Lighting Kit. Every state has different policies and
procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may receive
while using this lighting kit. This lighting kit is for off road use only.
Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit
will void all warranties.
The power switch that is used to power the lighting strips must be installed in a dry and accessible location! Having this part
exposed to water or the elements will cause the power switch to fail. Any water damage or corrosion to this part will VOID all
warranties.
It is recommended to install each motorcycle lighting strip using 3M™ Adhesion Promoter which allows for a much stronger bond
between the adhesive tape of the lighting strip and the cleaned mounting surface of your motorcycle. This is an optional installation
accessory that is NOT included with your motorcycle lighting kit.
PLEASE READ THE FOLLOWING INSTRUCTIONS THROUGHLY BEFORE INSTALLING AND OPERATING THIS
LED MOTORCYCLE KIT.
Motorcycle Kit Installation:
1. Upon receiving your new motorcycle lighting kit, we ask that you first test the kit to ensure it is functioning properly.
Connect the white stripe power wire to the positive terminal of the battery and the black ground wire to the negative
terminal of the battery. Once the wires are temporarily secure, power the kit to ensure full functionality before installing it.
If everything appears to be working correctly, turn the kit off and disconnect the power and ground wires from the battery
to prepare for installation.
2. Optional: Remove any trim pieces from your motorcycle that may hinder the installation of the lighting strips.
3. Begin by first laying out the LED lighting strips similar to the way they will be installed. Make sure that the wires will be
able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and strips away
from all moving parts that may come in contact with any part of the kit. IF A POWER WIRE IS PINCHED, IT WILL
CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY DUE TO PHYSICAL DAMAGE.
4. The power switch is NOT waterproof, so it must be mounted in a dry and accessible location.
5. Temporarily place the lighting strips to their intended mounting locations and route the power wires to the planned power
switch mounting area. Use the supplied zip ties to secure the wires to their mounting points. Be sure to keep the power
wires away from the suspension, any direct heat sources and/or moving parts. A few recommended locations on your
motorcycle to mount the light strips are under the gas tank, lower frame rail, rear fender frame rail, triple trees, lower swing
arm, and under the seat.
6. Once the motorcycle lighting strips and wires have been mocked up, clean the proposed mounting surfaces with an alcohol
prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest bonding results
from the double sided adhesive tape. Note: The surface area must be free of all oils, moisture, dirt and wax in order for the
supplied adhesive tape to bond and adhere to the installation surface correctly. Optional: To achieve the strongest bond
between the lighting strips and the motorcycle, you can use 3M Adhesive Promoter, which is sold separately from your kit.
7. Mount each lighting strip to the cleaned and dry surface of the motorcycle by using the supplied 3M tape. Run the wires to
the planned location of the control box and secure the wire to the bike frame by using the included zip ties. Be sure to use
the zip ties, this is a very important step and should not be skipped. Once this step is complete and the lighting strips
and wires are secure, allow ample time for the adhesive to settle and cure. Repeat this step for the remaining strips included
with your kit.
8. Route the white stripe power wire from the power switch to the positive terminal of the battery and the black ground wire
to the negative terminal of the battery. If the wires need to be extended, use automotive grade, 16-18 gauge wire for the
power and ground wires only. Connect and secure the power supply lines only after everything is properly installed and
mounted. If you do not follow this step, the inline fuse on the white stripe power wire may blow.
9. The kit was designed using a modular locking plug system for connecting the motorcycle lighting strips to the power
switch by using the included wire harness. Start plugging the male connections from the strips and power switch into the
female connections of the harness. Secure the excess wires of the strips and harness to the frame of your bike using the
included zip ties. DO NOT CUT OR SHORTEN ANY WIRES, YOU WILL VOID THE WARRANTY.
10. If you removed any trim for this installation, you can now reinstall them and test the functionality of your kit by pressing
the power switch.
11. Expandability: This kit includes a 6pc wiring harness that allows an additional 4 LED lighting strips to be added to a 2pc
kit or 2 additional LED lighting strips to a 4pc kit for even further customization.
12. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.
Troubleshooting:
If the kit or lights do not appear to operate, first check the installed inline mini fuse.If the fuse is blown, check the wires on
the entire kit to ensure they are not cut, pinched or scorched. If there is no damage to any of the wires and no water damage is visible
to the power switch, replace the fuse and test the kit again. If the fuse is intact, clean the battery terminals, both the positive and
negative terminals. Corrosion to the battery terminal can cause a poor connection or simulate being disconnected.
For accessories, add-on kits, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.
LEDGlow Lighting, LLC ("LEDGlow") warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free
from defects in material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed
incorrectly, or (2) damaged by collisions, vandalism, other accidents, or similar causes.
For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to be
defective. After the warranty period, the Purchaser must pay all charges for parts and labor.
Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our website,
www.LEDGlow.com, to determine the warranty coverage in the countries in which they are located.
LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals.
Improper installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s
warranty does not cover any expenses incurred in removing Products that are defective or re-installing replacement Products in their place.
During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for
customers in the contiguous United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product must
be returned in its original carton or in a similar package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight prepaid, to
the Purchaser. LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time.
This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the
Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product tha t is in its original
packaging and unopened.
This limited warranty is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: IF PURCHASER BELIEVES THAT A PRODUCT IS DEFECTIVE IN MATERIAL OR
WORKMANSHIP, WRITTEN NOTICE WITH AN EXPLANATION OF THE CLAIM SHALL BE GIVEN PROMPTLY BY PURCHASER TO LEDGLOW. ALL
WARRANTY CLAIMS MUST BE MADE WITHIN THE WARRANTY PERIOD, AND ANY PRODUCTS RETURNED TO LEDGLOW MUST BE SHIPPED IN
ACCORDANCE WITH LEDGLOW’S PROCEDURES (INCLUDING USE OF RMA NUMBERS SUPPLIED BY LEDGLOW AFTER NOTIFICATION). THE
REPAIR OR REPLACEMENT OF ANY PRODUCT OR PART THEREOF SHALL NOT EXTEND THE ORIGINAL WARRANTY PERIOD. THE SPECIFIC
WARRANTY ON THE REPAIRED PART ONLY SHALL BE IN EFFECT FOR A PERIOD OF NINETY (90) DAYS FOLLOWING THE REPAIR OR
REPLACEMENT OF THAT PART, OR THE REMAINING PERIOD OF THE PRODUCT WARRANTY, WHICHEVER IS GREATER.
2. EXCLUSIVE REMEDY; ACCEPTANCE: PURCHASER'S EXCLUSIVE REMEDY AND LEDGLOW'S SOLE OBLIGATION IS TO SUPPLY (OR PAY FOR)
ALL LABOR NECESSARY TO REPAIR ANY PRODUCT FOUND TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD AND TO SUPPLY NEW OR
REBUILT REPLACEMENTS FOR DEFECTIVE PARTS. LEDGLOW WILL REFUND THE PURCHASE PRICE FOR SUCH PRODUCT ONLY IF REPAIR OR
REPLACEMENT FAILS TO REMEDY THE DEFECT. PURCHASER'S FAILURE TO MAKE A CLAIM AS PROVIDED IN PARAGRAPH 1 ABOVE OR
CONTINUED USE OF THE PRODUCT SHALL CONSTITUTE AN UNQUALIFIED ACCEPTANCE OF SUCH PRODUCT AND A WAIVER BY PURCHASER OF
ALL CLAIMS THERETO.
3. EXCEPTIONS TO LIMITED WARRANTY: LEDGLOW SHALL HAVE NO OBLIGATION TO PURCHASER WITH RESPECT TO ANY PRODUCT THAT IS
SUBJECTED TO ANY OF THE FOLLOWING: ABUSE, IMPROPER USE, NEGLIGENCE, ACCIDENT, MODIFICATION, FAILURE TO FOLLOW THE
OPERATING PROCEDURES OUTLINED IN THE USER'S MANUAL, FAILURE TO FOLLOW THE MAINTENANCE PROCEDURES IN THE SERVICE
MANUAL FOR THE PRODUCT, ATTEMPTED REPAIR BY NON-QUALIFIED PERSONNEL, OPERATION OF THE PRODUCT OUTSIDE OF THE PUBLISHED
ENVIRONMENTAL AND ELECTRICAL PARAMETERS, OR IF THE PRODUCT'S ORIGINAL IDENTIFICATION (TRADEMARK, SERIAL NUMBER)
MARKINGS HAVE BEEN DEFACED, ALTERED, OR REMOVED. LEDGLOW EXCLUDES FROM WARRANTY COVERAGE PRODUCTS SOLD AS IS
AND/OR WITH ALL FAULTS. LEDGLOW ALSO EXCLUDES FROM WARRANTY COVERAGE ANY CONSUMABLE ITEMS SUCH AS FUSES AND
BATTERIES.
All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.
PROOF OF PURCHASE; REGISTRATION: The Purchaser's dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty.
EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY
WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL
CODE OR IN ANY OTHER STATE STATUTE.
THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER'S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE
ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR
ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON
WHATSOEVER.
GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding
their conflicts of laws principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty.
This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult
applicable state or country laws for a full determination of rights.
ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER
TERMS AND CONDITIONS
DISCLAIMER OF WARRANTY
LIMITATION OF LIABILITY
Loading...