LEDGlow Classic Single Color Flexible Motorcycle Lights User Manual

6-20pc Classic LED Motorcycle Light Kit

Motorcycle Kit Includes:

 Motorcycle LED Lighting

Strips

 (1) Control Box
 (1) Wireless Remote

 Wire Harness
 Zip-Ties

Warning: Please check your state and local laws before installing this Motorcycle Lighting Kit. Every state has different policies
and procedures in place regarding aftermarket LED lighting accessories. LEDGlow is not responsible for any fines that you may
receive while using this lighting kit. This kit is for off road use only.

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this
kit will void all warranties.

The control box that is used to power the motorcycle lighting strips must be installed in a dry location! Having this part

exposed to water or the elements will cause the kit’s controller to fail. Any water damage or corrosion to this part will

VOID all warranties.

It is recommended to install each motorcycle lighting strip using 3M™ Adhesion Promoter which allows for a much stronger
bond between the adhesive tape of the light strip and the cleaned mounting surface of your motorcycle. This is an optional
installation accessory that is NOT included with your motorcycle lighting kit.

PLEASE READ THE FOLLOWING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING AND OPERATING
THIS LED MOTORCYCLE KIT.

Motorcycle Kit Installation:

1. Upon receiving your new motorcycle lighting kit, we ask that you first test the kit to ensure it is functioning properly.

2. Optional: Remove any trim pieces from your motorcycle that may hinder the installation of the lighting strips.

3. Begin by first laying out the LED lighting strips similar to the way they will be installed. Make sure that the wires will

4. Temporarily place the motorcycle lighting strips to their intended mounting locations and route the power wires to the

5. Once the motorcycle lighting strips and wires have been mocked up, clean the proposed mounting surfaces with an

6. Mount each lighting strip to the cleaned and dry surface of the motorcycle by using the supplied 3M tape. Run the

Connect the red power wire to the positive terminal of the battery and the black ground wire to the negative terminal of
the battery. Once the wires are temporarily secure, power the kit to ensure full functionality before installing it. If
everything appears to be working correctly, turn the kit off and disconnect the power and ground wires from the battery
to prepare for installation.

be able to be routed in such a way that they will not be pinched, cut or exposed to heat. Also, keep the wires and strips
away from all moving parts that may come in contact with any part of the kit. IF A POWER WIRE IS PINCHED, IT

WILL CAUSE THE KIT TO MALFUNCTION AND WILL VOID THE WARRANTY DUE TO PHYSICAL
DAMAGE.

planned control box mounting area. Use the supplied zip ties to secure the power wires to their mounting points. Be
sure to keep the power wires away from the suspension, any direct heat sources and/or moving parts. A few

recommended locations on your motorcycle to mount the light strips are under the gas tank, lower frame rail, rear
fender frame rail, triple trees, lower swing arm, and under the seat.

alcohol prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest
bonding results from the double sided adhesive tape. Note: The surface area must be free of all oils, moisture, dirt, and
wax in order for the supplied adhesive tape to bond and adhere to the installation surface correctly. Recommended: To
achieve the strongest bond between the lighting strips and the motorcycle, you can use 3M Adhesive Promoter, which
is sold separately from your kit.

wires to the planned location of the control box and secure the wire to the bike frame by using the included zip ties. Be
sure to use the zip ties, this is a very important step and should be not skipped. Once this step is complete and the
lighting strips and wires are secure, allow ample time for the adhesive to settle and cure. Repeat this step for the
remaining strips included with your kit.

7. Find a secure and dry place to mount the control box. We recommend mounting it under the seat or in a water tight

compartment if possible. If this is not possible then we suggest mounting the control box in the driest place available.

The control box is not designed to withstand any water damage and if any does occur, it will void all warranties.
Optional: Seal the end caps of the control box with silicone to prevent water damage.

8. Connect the red power wire from the control box to the positive terminal of the battery. If the power wire needs to be

extended, be sure to use 16 or 18 gauge automotive grade wire. Be sure to reinstall the fuse within 6 inches of the
battery. Connect the black ground wire to the negative terminal of the battery.

9. The kit was designed using a modular locking plug system for connecting the motorcycle lighting strips to the control

box by using the included wire harness. Start plugging the male connections from the strips and control box into the
female connections of the harness. Secure the excess wires of the strips and harness to the frame of your bike using the
included zip ties. DO NOT CUT OR SHORTEN ANY WIRES, YOU WILL VOID THE WARRANTY.

10. If you removed any trim for this installation, you can now reinstall them and test the functionality of your kit by

pressing the on/off button on the wireless remote.

11. For more information, please refer to our instructional videos that can be found at www.YouTube.com/LEDGlow.

Wireless Remote Functions:

This kit provides multiple lighting patterns and several brightness levels, which are easily operated using the included

wireless remote. The remote includes four buttons, “A, B, C, D”

Button A: Powers the Kit ON and Controls 4 Brightness Levels.
Button B: Controls 3 Strobing Modes
Button C: Controls Fading Mode
Button D: Turns the Kit OFF

Reprogramming the Wireless Remote:
Remove the end cap from the control box and slide the circuit board out of the housing. Remove the tape from around

the circuit board. Once the tape is removed, you will see a white box on the circuit board that says “key”. Using a paper clip,
touch the two silver tabs that are located at the bottom of the “key” box. Once you touch the two silver tabs, a red LED will

illuminate. While the LED is lit, press any button on the wireless remote and you will see the LED flash and turn off. Press the
“A” button on the remote to power the kit and ensure it is functioning properly. Place the tape back on the circuit board and slide
it back into the housing of the control box.

Troubleshooting:
If the kit or lights do not appear to operate, first check the installed inline mini fuse. If the fuse is blown, check the

wires on the entire kit to ensure they are not cut, pinched or scorched. If there is no damage to any of the wires and no water
damage is visible to the control box, replace the fuse and test the kit again. If the inline fuse is intact, clean both the positive and
negative terminals of the battery. Corrosion to the battery terminal can cause a poor connection or simulate being disconnected.

For accessories, add-on kits, replacement parts and/or technical support, please visit www.LEDGlow.com for more information.