Lectrosonics SRHARNESS, SRSNYSCREWKIT Data Sheet
SR ADAPTERS
JMP-1
1
2
RX ON (REMOTE)
UART TX
UART RX
UART TX
UART RX
CH1 AUDIO (+) OUT (HOT)
DB-25
EXTERNAL POWER GND
CH1 AUDIO (+) OUT (HOT)
CH1 AUDIO (–) OUT (COLD)
CH1 AUDIO (–) OUT (COLD)
EXTERNAL POWER GND
RX ON (REMOTE)
CH1 AUDIO GND (SHIELD)
CH1 AUDIO GND (SHIELD)
CH2 AUDIO (+) OUT (HOT)
CH2 AUDIO (+) OUT (HOT)
CH1 AUDIO GND (SHIELD)
CH1 AUDIO GND (SHIELD)
CH2 AUDIO (–) OUT (COLD)
CH2 AUDIO (–) OUT (COLD)
For Camera Slot and Stand-alone Use
TECHNICAL DATA
SRSUPER Unislot Camera Adapter Kit Contents
Adapter kit for
Unislot® camera
slots such as those
provided on Ikegami®
and Panasonic® cameras.* Includes bezel,
hardware and rear
panel DB25 connector wired for power
and audio connections.
SRSNY Sony Camera Adapter Kit Contents
SRSUPER Adapter Mounting
Thread two short
screws through the
recessed tabs on the
adapter and slide it
onto the receiver housing. Thread two short
screws through the
tabs on the receiver
flange as shown.
On the opposite side,
thread two long screws
through the tabs on the
receiver flange, then
align them with the
tabs on the adapter.
Slide the adapter
up and tighten the
retaining screws
to secure it to the
receiver flange.
Adapter kit for Sony®
camera slots,* in-
SRSNY Adapter Mounting
cludes bezel, hardware, spare gasket
and rear panel DB15
connector wired for
power and audio
The smaller screws thread through the
adapter and into the camera body. The
larger screws mount the receiver flange
to the adapter.
connections.
Larger screws (4) attach
receiver to the adapter
NOTE: If you are having difficulty inserting
the receiver into the camera slot, try mounting
the blue adapter plate to the camera first, then
inserting the receiver.
Smaller screws (4) attach the
adapter to camera body
SREXT Adapter for Stand-alone Use
21747 6 ft. cable
This kit includes
an output and
power panel with
two TA3 male,
balanced outputs
and a power jack
with a locking
connector. A 6
foot power cable
is included.
Installing Rear Panel Adapters
Installation of the rear panel output/power adapters is the
same for all models.
Panels are held in
place by two phillips
head screws on the
sides of the housing.
Connections between the panel and
main circuit board
are made via miniature mating connectors.
Carefully align the
mating connectors
and gently slide the
panel straight into
the housing until the
screw holes align
with the housing.
SRHARNESS Adapter for Stand-alone Use
The two balanced
audio outputs and
the power cable are secured to the panel with
rugged strain reliefs.
Cables are 6 feet long
and audio cables are
shielded. No connectors are provided.
UniSlot® is a trademark of Ikegami Tsushinki Co., Ltd.
Ikegami
Panasonic
Sony
®
is a registered trademark of Ikegami Tsushinki Co., Ltd.
®
is a registered trademark of Matsushita Electric Industrial Co., Ltd.
®
is a registered trademark of Sony Kabushiki Kaisha TA Sony Corporation.
Mating Power Connector Dimensions
Replacement Screw Kits
Replacement screw kits are available:
SRSNYSCREWKIT
Contains:
5 - #28863 (.45 x 11mm)
5 - #28864 (.50 x 11mm)
5 - #28869 (shortest)*
* For Housing
SRUNISCREWKIT
(also for SRSUPER adapter)
Contains:
3 - #28862 (.50 x 20.5mm)
5 - #28864 (.50 x 11mm)
3 - #28869 (shortest)*
* For Housing
Loading...