Lectrosonics SNA600A User's Guide
SNA600a
-15
60
120
150
180
o
210
240
300
330
0
30
o
oo
o
o
-15
60
120
150
180
o
210
240
300
330
0
30
o
oo
o
o
-15
30
60
90
o
120
150
180
o
210
240
270
o
300
330
o
-15
60
120
150
180
o
210
240
300
330
0
30
o
oo
o
o
Adjustable Dipole Antenna
Half-Power Points
TECHNICAL DATA
• SWR less than 2:1 over 100 MHz bandwidth
• Adjustable elements tune center frequency from
550 to 800 MHz
• 3/8” x 16 threaded socket and stud with
mounting strap included
• Built in balun matched to 50 ohm BNC
connector
• Folds for storage
• Can be used with antenna power enabled on the
receiver or multicoupler
Antenna Scale
Center Frequency
The SNA600a antenna is a versatile tool for use with
wireless microphone receivers or IFB transmitters. The
center frequency of its 100 MHz bandwidth is tunable
from 550 to 800 MHz; however, the roll-off above and below this band is gradual. The SNA600a measures lower
than a 2:1 SWR (Standing Wave Ratio) from 465 MHz to
850 MHz when the antenna arms are fully extended.
The frequency is set by adjusting the dipole elements
(arms) using the scale printed on the body of the antenna. The elements fold for storage.
The body of the antenna is made of fiberglass circuit
board material. Nomenclature is printed in copper on
the board with a black solder mask to provide excellent
visual contrast. Copper traces on the circuit board form
a balun for an ideal match to a 50 ohm line via a standard BNC connector. Can be used with antenna power
enabled on the connected receiver or multicoupler.
minimum
sensitivity
Typical Vertical Pattern
Typical Horizontal Pattern
Antenna Scale
Adjusting
Screws
Folded Arm
(element)
Adjust center frequency
1. Fold arm (element) down to Antenna Scale.
2. Loosen screws to adjust arm size.
3. Line-up end of arm to center frequency.
4. Tighten screws gently.
5. Extend arm to T position.
6. Repeat on opposite side.
The coverage pattern of the antenna is circular, with maximum
sensitivity perpendicular to the adjustable elements.
maximum sensitivity
transmitter
Rio Rancho, NM, USA
www.lectrosonics.com
m
Ceiling or Table Top
Mounting
Corner Mounting
Wall Mounting
The SNA600a is supplied in a kit that includes a mounting strap and stainless steel mounting stud with hardware.
A sturdy mounting block is provided at
end of the antenna body, threaded for
the supplied 3/8” x 16 mounting stud
and a standard microphone stand. The
threaded hole’s symmetrical configuration allows the block to be unscrewed
and repositioned in 90° increments.
The threaded stud also adapts to the
optional mounting adapter kit.
Optional Mounting Adapter Kit
The ALPKIT includes four adapters for mounting the antenna on photo and video tripods, lighting equipment, and
standard microphone stands. The parts are constructed
of stainless steel for lasting durability.
Individual components in the kit can also be purchased
separately. Part numbers are provided below.
P/N 26313
Microphone stand
adapter. 5/8”-27 thread,
with 3/8”-16 thread in
other end. 1.5” long.
P/N 26311
Threaded adapter
for standard lighting
P/N 26312
Threaded adapter
for photo/video
tripod mounting. 1/2”
diameter x 1.75” long.
3/8”-16 thread on one
end, 1/4”- 20 on the
other.
P/N 28770
1/4” - 20 threaded adapter.
clamps. 1/2” diameter
x 6 inch long 3/8”-16
thread on both ends.
Mounting with the furnished strap:
Adjustable elements should be oriented vertically, away
from reflective metallic surfaces.
The mounting bracket should be bent only once or twice
for installations. Bend the bracket at the notches. Repeated bending will cause the aluminum to fracture.
Note: The SNA600a is not intended to be mounted
permanently outdoors. The antenna is weather
resistant, but not weatherproof.
Replacement Parts
Part No. Description
26332 Mounting strap; aluminum
28769 Threaded stainless mounting stud
28790 3/8-16 stainless steel nuts
28407 3/8 lock washer
28108 6-32 nyloc stainless nut (element mounts)
25658 Size 6 belleville washer (element mounts)
Specifications
Impedance: 50 ohms
Connector Type: BNC
SWR: Less than 2:1 at +/- 50 MHz
3dB Bandwidth: 150 MHz
Usable Frequency Range: 465 to 850 MHz
Gain: 2.17dBi (isotropic) or 0 dBd (referenced to a dipole)
Antenna power blocking: Capacitive coupling for use with DC power on cable
Length: 7”
Width: 1” folded , 7” to 11” extended depending on frequency
Thickness: 1”
Weight: 3.5 oz.
581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com
(505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.co
21 August 2019
Loading...