Lectrosonics M2T Instruction Manual

M2T
Digital IEM Transmitter
INSTRUCTION MANUAL
Fill in for your records:
Serial Number:
Purchase Date:
Rio Rancho, NM, USA www.lectrosonics.com
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
2
LECTROSONICS, INC.
Table of Contents
Introduction ............................................................................ 4
What is Dante? .................................................................... 4
System Setup Procedures .................................................... 5
Summary of Steps ............................................................... 5
Panels and Features .............................................................. 6
M2T, M2T/E01, M2T/E02, M2T/E06 Front Panel ................. 6
M2T, M2T/E01, M2T/E02, M2T/E06 Back Panel ................. 6
Operating Instructions ......................................................... 7
IR (infrared) Port .................................................................. 7
USB Port .............................................................................. 7
Headphone Volume Adjustment ........................................... 7
Dante Ports (optional) .......................................................... 7
Ethernet Port ........................................................................ 7
Power Inlet ........................................................................... 7
Quick Sync ........................................................................... 7
Navigating the Menus .......................................................... 7
LCD Menu Map ....................................................................... 8
Menu Item Descriptions ........................................................ 9
RF Enable/Level ................................................................... 9
RF Tuning ............................................................................. 9
Sync Scan ............................................................................ 9
Sync Settings ....................................................................... 9
Sync FlexList™ .................................................................... 9
Audio Level/Trim ................................................................... 10
Audio Input Type .................................................................. 10
Audio Polarity ....................................................................... 10
Headphone Monitor ............................................................. 10
Front Panel Setup ................................................................ 10
Network Settings .................................................................. 10
Edit Names .......................................................................... 10
Restore Defaults .................................................................. 11
About .................................................................................... 11
Links ..................................................................................... 11
Accessories ........................................................................... 12
Hardware Installation ............................................................ 13
Unpacking the Unit ............................................................... 13
Items Included in the Box: .................................................... 13
Installing two M2T, M2T/E01, M2T/E02, M2T/E06
Transmitters into a Single Rack Space ............................... 14
Wireless Designer Software ................................................ 16
Firmware Update Instructions .............................................. 16
Specifications and Features ................................................. 16
Service and Repair ................................................................ 17
Returning Units for Repair ................................................... 17
Digital IEM Transmitter
Rio Rancho, NM
3
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
Introduction
The M2T, M2T/E01, M2T/E02, M2T/E06 Digital Half­Rack Transmitter with analog and digital Dante™ (optional) network audio inputs presents an excel­lent sounding IEM system with a unique level of per­formance in a wireless in-ear monitor system. With ultra-low latency, digital RF modulation and two stereo digital channels, the M2T, M2T/E01, M2T/E02, M2T/ E06 provides a truly unique IEM product for demanding, professional applications.
The M2T, M2T/E01, M2T/E02, M2T/E06 boasts a USB port for firmware updates and an IR port for fast setup. A large, high resolution, backlit LCD and large mem­brane switches provide an intuitive interface that is highly visible in daylight or dimly lit conditions.
The half-rack transmitter provides four audio inputs which can be individually configured to be analog or Dante compatible. The input connectors are full size XLR/TRS combo types for balanced line level analog signals. Input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. Analog signals are converted to an internal digital format which is then encoded, organized into packets, and passed to an RF modula­tor. The modulated RF signal is filtered before and after amplification to suppress out-of-band noise and spuri­ous signals.
Conventional in-ear wireless monitor systems rely on decades-old technology: FM transmission with multi­plexed, companded audio. The M2T, M2T/E01, M2T/ E02, M2T/E06 Transmitter employs unique technology to provide ruler-flat frequency response from 20 Hz to 15 kHz and maximum channel separation. In addition, the digital audio eliminates a compandor and the as­sociated artifacts. The result is crystal clear sound and extremely low distortion of <0.15%.
The M2T, M2T/E01, M2T/E02, M2T/E06 is designed and developed with the professional touring, installation, theater and broadcast customers in mind. The transmit­ter chassis is all-metal. The front panel is an aluminum extrusion with a durable powder coat finish.
What is Dante?
Audinate’s patent pending Dante™ technology is a flexible Internet Protocol (IP) and Ethernet based digital AV network technology that eliminates the many bulky cables needed to provide point-to-point wiring for ana­log AV installations.
With Dante, existing infrastructure can be used for high performance audio as well as for ordinary control, moni­toring or business data traffic. Digital networks utilize standard IP over Ethernet offering high bandwidth ca­pable of transporting hundreds of high quality channels over Gigabit Ethernet.
Set-up and configuring the system is made easy as well, saving enormous installation costs and long term cost of ownership on a digital network. The physical connecting point is irrelevant: audio signals can be made available anywhere and everywhere. Patching and routing now become logical functions configured in software, not via physical wired links
Summary of Dante Benefits
• Plug-and-play technology – automatic discovery and simple signal routing
• Reduced Cost & Complexity- No special skills required to set up audio networking
• Sample accurate playback synchronization
• Add/remove/rearrange components at will
• Deterministic latency throughout the network
• Support mixed bit depths and mixed sample rates over one network
• Scalable, flexible network topology supporting a large number of senders and receivers
• Supports 1Gbps networks
• Supports a single integrated network for audio, video, control, monitoring
• Uses inexpensive, off-the-shelf computer networking equipment
4
LECTROSONICS, INC.
System Setup Procedures
Summary of Steps
1) Connect power using supplied DCR15/4AU power supply.
2) Power receiver and scan RF spectrum on site.
3) Sync Scan to transfer information from receiver to transmitter.
4) Tune transmitter to unoccupied channels in scan.
5) Sync receiver (refer to receiver manual).
6) Turn on transmitter RF.
7) Send audio sources to transmitter.
WARNING: Increasing the Pregain can make headphone volume excessively loud. Use caution when setting and using.
Digital IEM Transmitter
Rio Rancho, NM
5
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
Panels and Features
M2T, M2T/E01, M2T/E02, M2T/E06 Front Panel
Menu/Select
Reset Button
Headphone Volume
Adjustment
Headphone Jack
Return to
previous screen
Channel Function
Buttons/
Quick Sync
M2T, M2T/E01, M2T/E02, M2T/E06 Back Panel
Antenna
Jack
Dante Ports (optional)
Menu navigation
buttons
USB Port
Power switch
IR Port
Antenna
Jack
XLR/TRS Combo Analog
Power Inlet
6
Input Connectors
Ethernet Port
LECTROSONICS, INC.
Digital IEM Transmitter
Operating Instructions
IR (infrared) Port
Settings, including frequency, name, limiter, mix mode, etc. can be transferred to and from the M2T, M2T/E01, M2T/E02, M2T/E06 transmitter via this port to an IR enabled receiver to simplify setup.
USB Port
For firmware updates and connection to Wireless De­signer Software.
Reset Button
For MCU recovery in the event of an interrupted firm­ware update.
Headphone Volume Adjustment
Adjust the headphone volume, and select source with A1, A2, B1, B2 buttons.
Antenna Output Jacks
Two standard 50 ohm BNC connectors can be used with whip antennas or coaxial cable connected to re­mote antennas.
Dante Ports (optional)
A Dante Digital Audio Network Interface.
Power Screens
When powering on the M2T, M2T/E01, M2T/E02, M2T/ E06, there are three screens that appear in the follow­ing order, Duet, Lectrosonics, RF On/Off.:
Simultaneous long press of A1/A2 (TX A) or B1/B2 (TX B) will also enable or disable RF.
WARNING: If RF ON is selected and the user chooses to “Do Not Show Again” RF transmissions will be on when M2T, M2T/E01, M2T/E02, M2T/E06 is powered on and may interfere with frequencies already in use. This can be reset in the FRONT PANEL menu.
Ethernet Port
Used for setup, monitoring and control with Wireless Designer Software.
Power Inlet
The threaded-locking DC coaxial jack accepts 9-18 VDC and draws 1.2A maximum.
Quick Sync
Sync an M2R rapidly by utilizing the Channel Function Buttons. A long (1 second) press of one of the buttons (A1, A2, B1, or B2) on the front panel initiates Quick Sync. Two options are available, “SYNC ALL” or “SPLIT MONO”. The mode is selected prior to sync in the Front Panel Setup menu item.
NOTE: See Front Panel Setup for more instruction on the Quick Sync function.
Navigating the Menus
All Menu setup items are arranged in a vertical list on the LCD. Press MENU/SEL to enter the menu, then navigate with the UP and DOWN arrows to highlight the desired setup item. Refer to the menu map on the following page.
NOTE: To guarantee chosen parameters are saved, exit a setup screen BEFORE powering down M2T, M2T/E01, M2T/E02, M2T/E06.
Press MENU/
SEL to enter
the menu
Press MENU/SEL to enter the setup of the highlighted
item
Press the UP and DOWN arrows
to navigate and highlight the
desired menu item
Press the UP and DOWN arrows
to navigate and highlight the
desired item
Rio Rancho, NM
Press BACK to return to
the previous screen
7
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
LCD Menu Map
RF ENABLE/LEVEL
RF TUNING
SYNC SCAN
SYNC SETTINGS
SYNC FLEXLIST
AUDIO LEVEL/TRIM
AUDIO INPUT TYPE
SEL
SEL
SEL
SEL
SEL
SEL
SEL
RF ENABLE/LEVEL
BACK
BACK
BACK
BACK
BACK
BACK
BACK
SYNC SETTINGS
SYNC FLEXLIST
AUDIO LEVEL/TRIM
AUDIO INPUT TYPE
RF TUNING
SYNC SCAN
Press SEL to select desired adjustment step
Press SEL to select desired adjustment step
Press SEL to select desired function
Press SEL to select desired function
Press SEL to select desired function
Press SEL to select desired channel
Use arrow keys to select desired channel
Use arrow keys to enable or adjust
Use arrow keys to select desired frequency
Use arrow keys to select desired sync command or tune frequency
Use arrow keys to select desired sync command
Press SEL to engage function
Use arrow keys to adjust setting
Use arrow keys to select desired audio setting
AUDIO POLARITY
HEADPHONE
MONITOR
FRONT PANEL
SETUP
NETWORK SETTINGS
EDIT NAMES
RESTORE
DEFAULTS
ABOUT
SEL
SEL
SEL
SEL
SEL
SEL
SEL
BACK
BACK
BACK
BACK
BACK
BACK
BACK
AUDIO POLARITY
HEADPHONE
CONFIG
FRONT PANEL
SETUP
NETWORK SETTINGS
EDIT NAMES
RESTORE DEFAULTS
ABOUT
Press SEL to select desired channel
Use arrow keys to select desired headphone output setting
Press SEL to select desired function
Press SEL to select desired adjustment step
Press SEL to select desired function
Use arrow keys to select yes or no
No selections available; for information purposes only
Use arrow keys to select desired audio setting
Use arrow keys to adjust desired front panel setting
Use arrow keys to adjust desired settings
Use arrow keys to enter desired name
Press SEL to execute
LINKS
8
SEL
BACK
LINKS
No selections available; use phone to scan QR code for more information
LECTROSONICS, INC.
Digital IEM Transmitter
Menu Item Descriptions
RF Enable/Level
Allows RF transmission to be turned on and off and set RF levels at 10, 25 or 50 mW (E06 options are 20, 50 or 100 mW EIRP).
RF Tuning
Allows manual selection of the operating frequency.
Sync Scan
Receive frequency scan via IR port or tune transmitters manually.
Sync Settings
Allows sending or retrieving setup data via IR port.
Sync FlexList™
FlexList allows the user to set up a list of profiles, by name, in the receiver. This allows quick and easily ac­cess to listen to any of the mixes on site.
After putting the receiver into Sync Flex mode, choose the function and then use the transmitter to send the profile over IR:
Stereo Mix: The current receiver settings are sent as
is, except the mix mode is set to stereo.
Mono Ch. 1 Only: The current receiver settings are
sent as is, except the mix mode is set to Mono Ch. 1.
Mono Ch. 2 Only: The current receiver settings are
sent as is, except the mix mode is set to Mono Ch. 2.
Screen will alert user if scan is unsuccessful.
NOTE: See Mix Mode for more information.
Rio Rancho, NM
9
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
Audio Level/Trim
Set audio inputs at correct levels.
Easily switch between
channels with A1, A2, B1
or B2 Buttons.
Audio Input Type
Set independent channels to analog or digital (Dante), if available.
Front Panel Setup
Front panel settings may be customized as follows:
• LCD brightness
• Front panel lock
• Startup RF state
• Quick Sync Mode
Sync All: A long (1 second) press of
either the A1, A2, B1 or B2 buttons sends all RX1 settings.
Split Mono: A long press of the A1or B1
buttons sends all RX1 settings with the mix mode forced to Mono Ch. 1. A long press of the A2 or B2 buttons sends all RX1 settings with the mix mode forced to Mono Ch. 2.
Network Settings
Allows the user to set IP address or other network set­tings when needed.
NOTE: When selecting a Dante input, user must be familiar with the Dante Controller from Audinate.
Audio Polarity
Select normal or inverted polarity for each audio channel.
Headphone Monitor
The headphone source can be selected here or on the front panel, using the A1, A2, B1 or B2 Buttons.
NOTE: New network settings require the unit to reboot to take effect. Making a change and pressing the BACK key will prompt the user to Reboot Now, Save and Exit, or Discard and Exit.
Edit Names
Edit names to match talent for easy location in the Flex­List or easily identify multiple M2T, M2T/E01, M2T/E02, M2T/E06 transmitters in a rack.
• Use UP and DOWN Arrows to select letters and MENU/SEL to set and move cursor.
10
LECTROSONICS, INC.
Restore Defaults
Returns all settings to the factory defaults.
About
Displays general information about the M2T, M2T/E01, M2T/E02, M2T/E06, including serial number, and the hardware, FPGA and microcontroller firmware versions.
Links
QR codes with links to the Lectrosonics website, the M2T, M2T/E01, M2T/E02, M2T/E06 User Manual online and YouTube video tutorials.
Digital IEM Transmitter
Rio Rancho, NM
11
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
SNA600a Antenna
Accessories
DCR15/4AU
Front Mount Antenna Kit FMAKM2T
SNA600a Accessories:
27080 Dante Port Cover
(included with Non-Dante Model)
ARG 15
A 15 foot antenna cable of standard RG-58 coax cable with BNC connectors at each end.
Dante 4X4-TM Dante Card Kit (Included in Dante Model)
RMPM2T-1
Rack kit for mounting one M2T, M2T/E01, M2T/E02, M2T/E06 into a single rack space
ARG 25; ARG 50; ARG 100
Antenna cable of Belden 9913F low-loss coax cable with BNC connectors at each end. Number speci­fies length in feet.
External Power Accessories:
LTBATELIM
Battery Eliminator for LT, DBu and DCHT transmitters, and M2R; camera hop and similar applications. Optional power cables include: P/N 21746 right angle, locking cable; 12 in. length P/N 21747 right angle, locking cable; 6 ft. length; DCR12/A5U universal power supply for AC power.
12
LECTROSONICS, INC.
Hardware Installation
DCR15/4AU DC
power supply
Digital IEM Transmitter
21926
Cable USB
25990 Bracket
rear tie
(4) 28885 SCR10
cap screw
35800 Hex L
key wrench
(4) 35664 Rubber
foot large
25991 Bracket
front tie
27076 Rack
flange bracket
27082 Rack handle
35959 Hole Plug
(2) A500RA20
Antenna
Unpacking the Unit
Compare the packing list enclosed with the M2T, M2T/ E01, M2T/E02, M2T/E06 with the original order. Inspect all items for damage. Immediately call 1-800-821-1121 to report any items that are missing or damaged. The sooner we get notified, the sooner we can get any needed replacement items shipped to your location.
Rio Rancho, NM
Items Included in the Box:
(DCR15/4AU) Power supply cable
(21926) USB cable
(35800) Hex L key wrench
(25990) Bracket rear tie
(25991) Bracket front tie
(27076) Rack flange bracket
(27082) Rack handle
(28885) (4) SCR10 cap screw
(35664) (4) Rubber foot large
(35959) Hole plug
(A500RA20) (2) Antenna
Instruction manual
13
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
Installing two M2T, M2T/E01, M2T/E02, M2T/E06 Transmitters into a Single Rack Space
The M2T, M2T/E01, M2T/E02, M2T/E06 transmitter oc­cupies a half rack space, and comes with hardware to mount two transmitters into a single rack space.
1. Remove the Trim Cap (Part #P1330) from both sides of the front panel on both transmitters.
2. Remove the breakaway tabs on both sides of the chassis side panels. Use a flat blade screwdriver to pry the tabs outward and snap them off of the chassis.
4. Insert two (2) cap screws (Part #28885) through the rack handle (Part #27082) holes and install the rack handle onto the flange bracket through the holes in the unit’s front panel. Firmly tighten the cap screws using the hex key (Allen wrench) as shown.
5. If antennas will NOT be mounted on the front panel of the transmitters, install the hole cap (Part #35959) by aligning the flat on the cap with the flat on the opening.
3. Insert the flange bracket (Part #27076) into the open slot in the side of the chassis cover panel.
NOTE: The retaining nuts on the panel and tie brackets are “tensioning lock nut” types designed to prevent the screws from coming loose due to vibration. You will usually feel resistance as you tighten the screws - this is normal.
14
LECTROSONICS, INC.
Digital IEM Transmitter
Rear tie bracket
(Part #25990)
Tensioning lock nuts on the rear
side of the bracket
6. Install one side of the front tie bracket (Part #25991) into the side panel opening in one of the transmit­ters. Insert the screws, but do not tighten them completely at this point.
7. Remove the four cap screws from the adjacent rear panels, and then use them to attach the rear tie bracket. Do not tighten the screws completely.
Front tie bracket
(Part #25991)
Slide the other transmitter over the tie bracket and
insert the screws, but do not tighten them complete­ly until the rear tie bracket is installed.
8. After front and rear tie brackets are installed, place the transmitters on a flat surface so the that the front panels are even with each other. Hold the transmitters in place and tighten all cap screws on the front and rear brackets.
Rio Rancho, NM
NOTE: If the supplied rubber feet are installed on under side of M2T, M2T/E01, M2T/E02, M2T/ E06, it will not fit in a rack unless there is an empty space below it.
15
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
Wireless Designer Software
Download the Wireless Designer software installer from the web sites under the SUPPORT tab at:
http://www.lectrosonics.com/US
Wireless Designer only needs to be installed the first time the software is used. Once the software is in­stalled, updates are available by simply clicking on an item in the Help Menu.
NOTE: If Wireless Designer is already installed, you must uninstall it before attempting to install a new copy.
Firmware Update Instructions
Firmware updates are made with a file downloaded from the web site and the DSQD connected via USB.
The USB port on the transmitter requires a micro-B male plug on the connecting cable. The other end of the cable would normally be a USB A-Type male con­nectorto fit the most common type of USB jack used on computers.
Refer to Help in Wireless Designer software for the procedure.
Specifications and Features
RF Power Output:
• Two carriers; two audio channels each
• M2T, M2T/E02: Power adjustable on each carrier to 10, 25 or 50 mW
M2T/E06: Power adjustable on each carrier to 20, 50 or 100 mW EIRP
Antenna Output: 2 x BNC sockets
Operating Frequencies:
M2T 470.100 – 607.975 MHz
M2T/E01 470.100 - 614.375 MHz
M2T/E02 470.150 - 614.375 MHz
M2T/E06 520.000 - 614.375 MHz
NOTE: It’s the user’s responsibility to select the approved frequencies for the region where the transmitter is operating
Frequency Selection Steps: 25 kHz
Frequency Stability: ± 0.002%
Modulation: 8 PSK
Emission Designator: 200KG7E
Spurious Radiation: Compliant with ETSI EN 300 422-1
Equivalent input Noise: –128 dBV
Latency: (overall system)
Digital Source: 1.0 ms plus Dante network (on Dante unit)
Analog Source: <1.4 ms
Audio Frequency Response: 10 Hz – 11.5 kHz, -1 dB
Audio Input: -10 dBV or +4 dBu settings w/ ±5 dB trim
Audio Input Jack: 4 x combo XLR/TRS connectors
Input impedance: Line: 2k Ohm
Dante Connection: 2 x RJ45, 4 audio RX channels, internally routable
Ethernet Connection: RJ45
USB Connection: Micro USB on front panel for firmware updates
IRDA: IR transceiver for sync of receivers
Headphone jack 3.5 mm stereo jack
Power Requirements: 9-18 VDC
Power Consumption: 5 Watts
Weight: 2.2 lbs (997.903 grams)
Dimensions: Height: 1.750 in. / 44.45 mm
Width: 8.375 in. / 212.7 mm
Depth: 7.750 in. / 196.8 mm
16
Specifications subject to change without notice.
LECTROSONICS, INC.
Digital IEM Transmitter
Service and Repair
If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual.
We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at­tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working.
LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs.
Returning Units for Repair
For timely service, please follow the steps below:
A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need
to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time).
B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed
your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container.
C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the
proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed” for safe transport.
D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-
age to equipment that you ship. Of course, we insure the equipment when we ship it back to you.
Lectrosonics USA:
Mailing address: Shipping address: Telephone:
Lectrosonics, Inc. Lectrosonics, Inc. (505) 892-4501 PO Box 15900 561 Laser Rd. NE, Suite 102 (800) 821-1121 Toll-free Rio Rancho, NM 87174 Rio Rancho, NM 87124 (505) 892-6243 Fax USA USA
Web: E-mail: www.lectrosonics.com sales@lectrosonics.com
service.repair@lectrosonics.com
Lectrosonics Canada:
Mailing Address: Telephone: E-mail:
720 Spadina Avenue, (416) 596-2202 Sales: colinb@lectrosonics.com Suite 600 (877) 753-2876 Toll-free Service: joeb@lectrosonics.com Toronto, Ontario M5S 2T9 (877-7LECTRO) (416) 596-6648 Fax
Rio Rancho, NM
17
M2T, M2TND, M2T/E01, M2TND/E01, M2T/E02, M2T/E06
18
LECTROSONICS, INC.
Digital IEM Transmitter
ISEDC Notices:
Per RSS-210
This device operates on a no-protection no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. Please consult Industry Canada’s document CPC-2-1-28, Optional Licensing for Low-Power Radio Apparatus in the TV Bands, for details.
Ce dispositif fonctionne selon un régime de non-brouillage et de non-protection. Si l’utilisateur devait chercher à obtenir une certaine protection contre d’autres services radio fonctionnant dans les mêmes bandes de télévision, une licence radio serait requise. Pour en savoir plus, veuillez consulter le document CPC-2-1-28 d’Industrie Canada intitulé, Délivrance de licences sur une base volontaire pour les appareils radio de faible puissance exempts de licence et ex­ploités dans les bandes de télévision.
Per RSS-Gen
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
1) This device may not cause interference
2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio ex¬empts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep tible d’en compromettre le fonctionnement.
Rio Rancho, NM
19
m
LIMITED ONE YEAR WARRANTY
The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment.
Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.
This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase.
This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT.
This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state.
581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.co
25 May 2021
Loading...