Lecroy WS Remote Control

WAVESURFER OSCILLOSCOPE

Errata Sheet for Remote Control Manual

Most of the commands contained in the Remote Control Manual for the WaveMaster™ DSO and other
X-Stream
scope commands that are not in the manual. The Remote Control Manual can be found in the Technical
Library at LeCroy’s Web site http://www.lecroy.com

Please refer to the following table for additions, exclusions, and modifications.

™ instruments apply also to the WaveSurfer oscilloscope. There are also two new WaveSurfer

.

Command Status Notes

COMBINE_CHANNELS Not Applicable

CURSOR_MEASURE Modified

CURSOR_SET Modified

CURSOR_VALUE? Modified Allowed traces: F1, F5, F6, F7, F8, TA, C1, C2, C3, C4

CURSORS Not Applicable

DEFINE Modified

FUNCTION_RESET Mod if ied All o w e d f u n c t i o n s: F 1 o r TA.

GRID Modified Allowed arguments: SINGLE, XYONL Y, XYSINGLE

HOR_MAGNIFY Modified

HOR_POSITION Modified

Allowed modes: CUST [,ST AT], F AIL, HREL [,ABS, DE LT A,
SLOPE], OFF, PASS, VREL [,ABS, DELTA]

Allowed traces: F1, F5, F6, F7, F8, T A, C1, C2, C3, C4, M1, M2,
M3, M4

F5 to F8 correspond to Z1 to Z4, respectively.

Allowed function is F1 only.
Not all function parameters are allowed.

Allowed prefixes:
T A or F1 for the Math trace

Z1 to Z4 for F5 to F8
F2 to F4, TB to TD are not valid

Allowed prefixes:
T A or F1 for the Math trace

Z1 to Z4 for F5 to F8
F2 to F4, TB to TD are not valid

This command sets the input impedance.
Syntax:

IMPEDANCE New

INSP? Modified

1

<channel>:IMPEDANCDE <impedance>
<impedance>:= A1M, D1M, D50, GND, 0VL

For external trigger: D50, D1M, GND
Allowed prefixes:
C1 to C4 for channel traces

M1 to M4 for memory traces
T A or F1 for the Math trace
Z1 to Z4 for F5 to F8

WAVESURFER OSCILLOSCOPE

F2 to F4, TB to TD are not valid

MEMORY_SIZE Not Applicable

PARAMETER Modified

P ARAMETER_CL R Modified Pass/Fail is not applicable.

P ARAMETE R_CUSTOM Modified Only parameter columns 1 t o 6 allowed.

PARAMETER_DELETE Modified

PARAMETER_STATISTICS Modified

PARAMETER_VALUE? Modified

PASS_FAIL Modified

PER_CURSOR_SET Modified

PERSIST_SAT Modified Trace selection is not allowed.
PERSIST_SETUP Modified Allowed mode: ALL
SAMPLE_CLOCK Modified Allowed state s: INTERNAL, ECL, T TL, 0V

Allowed parameter types: CUST, OFF
Allowed parameter readout: ST AT, OFF

Pass/Fail is not applicable.
Only parameter column s 1 to 6 allowe d.
Allowed parameter type: CUST
Allowed parameters: P1 to P6
Allowed traces: F1, F5, F6, F7, F8, T A, C1, C2, C3, C4
Not allowed: CUST7, CUST8
<stop after> argument is not valid.
<logic> settings allowed: AllTrue, AllFalse
Allowed traces: F1, F5, F6, F7, F8, T A, C1, C2, C3, C4, M1, M2,

M3, M4

SEQUENCE Not Applicable

STORE_SETUP Modified F2 to F4, TB to TD are not valid

TRACE Modified F2 to F4, TB to TD are not valid

TRIG_COUPLING Modified

TRIG_LEVEL Modified ETM10 is not valid

TRIG_SELECT Modified New types: TV, RUNT, SLEW

TRIG_SLOPE Modified ETM10 is not valid

TRIG_WINDOW New

VERT_MAGNIFY Modified F2 to F4, TB to TD are not valid

VERT_POSITION Modified F2 to F4, TB to TD are not valid

WAVEFORM Modified F2 to F4, TB to TD are not valid

ETM10 is not valid
New values: AC, DC, HF, HFRE J, LFREJ

The TRIG_WINDOW command sets the window amplitude in
volts on the current Edge trigger source. The window is
centered around the Edge trigger level.

Syntax:
TRIG_WINDOW <value>

<value>:= 0 to 25 V

2