Leatt-Brace ADVenture User Manual
USER MANUAL
www.leatt-brace.com
™
The Leatt-Brace® cannot protect against all possible impacts and/or injuries. Although the Leatt-Brace® is
designed to help reduce the risk of such injuries, there is no guarantee that any injury will be prevented by the use of
this equipment. Perform any motor sport activity with caution and use/wear appropriate safety equipment.
For maximum performance, the Leatt-Brace® must be properly fi tted and attached according to the instructions in
the user manual. It is recommended that this product be used only in conjunction with a full-face helmet. Use at your
own risk.
For maximum performance, the Leatt-Brace® must be inspected prior to each use. STOP using the Leatt-Brace
®
if any components show signs of damage or are worn, cracked, and/or deformed, or if the inside padding is
deteriorated. Leatt
®
Corporation recommends that the Leatt-Brace® be replaced every two 2 years under
normal racing conditions.
Should you experience a collision or if the Leatt-Brace® or any component shows any signs of damage, cracking,
deformity and/or the inside padding is deteriorating, return the Leatt-Brace
®
to the seller for inspection or destroy
and replace the Leatt-Brace
®
.
Common substances applied to this brace (solvent, cleaners, hair tonics, etc.) can cause damage that may be
invisible to the user and compromise the effectiveness/safety of the Leatt-Brace
®
. Wash only with gentle soap or
detergent in cold water, rinse in cold water and dry with a soft cloth.
Do not drill holes, paint, cut, heat, bend, apply decals or stickers, or make any other modifi cations to the
Leatt-Brace
®
unless authorized in advance by the Seller. Doing so may compromise the effectiveness/safety of the
Leatt-Brace
®
.
The brace has been tested using various static and dynamic tests, but has not been tested on riders under race
conditions for instrumented impact assessment; this product is of a new design.
The brace has been tested on a wide range of users and vehicle types and should fi t you and your vehicle, if not,
minor adjustments may be required for proper fi t. Failure to properly adjust the brace before use may compromise
rider safety and brace effectiveness.
Always attach your helmet correctly according to seller’s guidelines. Ensure that all of your safety equipment has not
passed beyond its recommended life span. Travel/race with safety as your primary principle.
If you have any questions regarding this product or its proper use, please contact Leatt
®
Corporation at:
Leatt
®
Corporation South Africa
Unit 1, Kyalami Plaza, Kyalami Drive, Killarney Gardens, Cape Town, 7441, RSA
Tel: 0027 21 556 5409; Fax: 0027 21 557 3925
Leatt
®
Corporation USA
5348 Vegas Drive, #775, Las Vegas, Nevada 89108 USA
Tel: 702 447 6751; Fax: 702 447 6751
Email: info@leatt-brace.com
USER MANUAL
WARRANTY DISCLAIMER
NO EXPRESS WARRANTIES WITH RESPECT TO THE BRACE OTHER THAN THOSE EXPRESSLY SET FORTH
HEREIN HAVE BEEN PROVIDED.
LEATT® CORPORATION UNDERTAKES NO RESPONSIBILITY FOR THE QUALITY OF THE GOODS EXCEPT AS
OTHERWISE PROVIDED HEREIN. LEATT® CORPORATION TAKES NO RESPONSIBILITY THAT THE GOODS
WILL BE FIT FOR ANY PARTICULAR PURPOSE FOR WHICH YOU MAY BE BUYING THE GOODS, EXCEPT AS
OTHERWISE PROVIDED HEREIN. ALL IMPLIED WARRANTIES ARE HEREBY DISCLAIMED INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE.
Motor Sports and racing can be dangerous. Participation in these activities can result in
severe brain, head and neck injuries which may result in paralysis or death. Although the
Leatt-Brace® is designed to help reduce the risk of such injuries, there is no guarantee
that any injury will be prevented by the use of this or any other safety equipment. Read all
instructions prior to use. Before putting on your Leatt-Brace
®
each time, please review and
comply with the following cautions and instructions below.
01 02
Leatt-Brace® ADVenture™
Table of Contents
•
ADVenture™ Brace Exploded View .......................................... Page 03 - 04
•
Instruction Manual Introduction ................................................. Page 05
•
Brace Fitment
• Fitment and Adjustment of Pins .......................................... Page 06
• Padding Inserts ................................................................... Page 07
• Strut and Thoracic Assembly .............................................. Page 08 - 09
• Opening and Closing your Brace ........................................ Page 09
• Fitting the ADVenture™ Brace with a Roost Guard ............ Page 10
•
Fitting the ADVenture™ Brace with a Riding Jacket ........... Page 11
•
Chest Strap ............................................................................... Page 12
•
Looking after your Leatt-Brace® .............................................. Page 13
•
Indemnity and Warranty Disclaimer .......................................... Page 14
Copyright © 2008, Leatt® Corporation
Copyright © 2008, Leatt® Corporation
™
ADVenture™ Exploded View
03 04
1 - Adventure Front Component 1
2 - Adventure Front Padding 1
3 - Button Head Cap Screw M4 x 10mm 8
4 - Step Washer 2
5 - Hinge Lever Assembly 2
6 - Stainless Steel Washer 5
7 - Pin 3 pairs
8 - Adventure Thoracic Padding 1
9 - Adventure Thoracic Component 1
10 - Strut (10 degrees) 1
11 - Nylon Washer 2
12 - Shim 2
13 - Button Head Cap Screw M4 x 22mm 1
14 - Rivet 2,9 x 25mm 1
15 - Adventure Back Component 1
16 - Adventure Back Padding 1
17 - Adventure Padding Inserts 2
Parts/Components List QTY QTY
Copyright © 2008, Leatt® Corporation
Copyright © 2008, Leatt® Corporation
Loading...