LEADWARRIOR LW 35022 Flakpanzer II LUCHS User Manual
LW 35022
WWW.LEADWARRIOR.COM INFO@LEADWARRIOR.COM COPYRIGHT 2006
LEADWARRIOR
HISTORICAL MINIATURE
Ebay: LEADWARRIOR
SUPPORT@LEADWARRIOR.COM
WWW.LEADWARRIOR.COM
LW 35022
In second half of WWII, due to superiority of Allies in the
air, Germany faced an urgent need in armoured AntiAircraft vehicles. In May-September of 1943 Hitler
headed a few meetings dedicated to this matter, and the
‘Inspection 6’, responsible for developing of AA Panzers,
was established.
That was the beginning of numerous projects of the antiaircraft guns (Flak) utilizing any suitable chassis. The
shortage of linear tanks had influenced manufacturing of
AA-Panzers by mid 1944; The cheap and reliable chassis of
Pz.Kpfw.III were demanded for StuG Assault Guns
production, so the Pz.Kpfw IV chassis was used for
Flakpanzers construction, and several hundreds machines
of different types were built until the end of the war.
At the same time attempts were made to find any
substitution of chassis for AA-guns. One of the projects
was developed as result of deep modernization of chassis
of reconnaissance tank Pz.Kpfw.II Ausf. L “Luchs”.
It was supposed to carry a 37mm Flak 43 anti-aircraft
gun. To reduce the height of the construction, AA-gun was
mounted in armoured round barbette, which was
swamped into upper hull.
The chassis had to be lengthened. The weight
of the machine had grown, so the suspension
was rear ranged more dense, and two
additional brackets were added each side. The
engine remained the same as at Pz.Kpfw.II L,
so the speed of the vehicle dropped down, but
it was not so essential in the defense war
situation.
The construction became compact, and it’s
height was lower than of Pz.Kpfw.IV-based
Flakpanzers, but it was still quite complex in
production, so by the end of the was only a
wooden mockup was built.
47 RESIN PARTS
CONVERSION KIT for
ICM Pz.Kpfw. II Ausf L ‘Luchs’
and ITALIRI Flak 43
37mm FlaK 43 Sfi. auf Pz.Kpfw. II Ausf. L
FlakPanzer II
‘LUCHS’
3LW 35022
LW 35022
WWW.LEADWARRIOR.COM INFO@LEADWARRIOR.COM COPYRIGHT 2006
5
Icm 10
R 9
R 4
R 2
R 3
R 16
R 16
R 16
R 16
MOUNT Flak Gun
(Place
Flak43 kit Part A8
here)
R 3
Icm 11
R7 R8
Icm 22
Icm 20
R6
R17
R5
Icm 11
41,5 mm
6
7
8
Mount ICM kit parts #:
B28, B42, B26, B27, B30,
B37, B57, B52, B55, B11, B31, B7,
B34, B13, B2, B3, B4, B23, B32,
B1, B14, B29, B41, B54.
Assembly Tracks: Use ICM parts,
and R18 resin parts.
LW 35022 1
LW 35022
WWW.LEADWARRIOR.COM INFO@LEADWARRIOR.COM COPYRIGHT 2006
R 1
R 2
R 3
R 4
R 5
R 7
R 6
R 8
R 9
R 10
R 11 R 12
R 11 R 12
R 13 R 14 R 15
R 13 R 14 R 15
R 16
R 17
R 18 x 25
2
MAKE
?
Cut / Remove part
Optional
Repeat several times
Repeat on mirror side
ITALERI Flak 43 parts reworking
1
Flak 43 part 1A
Flak 43 part 29A Flak 43 part 64A
21 mm
LW 35022 2
LW 35022
WWW.LEADWARRIOR.COM INFO@LEADWARRIOR.COM COPYRIGHT 2006
2
1. Execute step 1 of ITALERI kit manual: DO NOT use parts 12B, 13B, 14B, 15B, 16A.
2. Execute steps 2 and 3 of ITALERI kit manual.
3. SKIP step 4 of ITALERI kit manual.
4. Execute steps 5 of ITALERI kit manual: DO NOT use parts 49A, 50A.
5. Execute step 6 of ITALERI kit manual.
Position 64A, 65A as follows:
ITALERI Flak 43 assembling
1A
65A
64A
6. Execute steps 7 of ITALERI kit manual:
DO NOT use module G1 or G2 .
DO NOT use part 70B.
USE alternative L for sight. Rework it
as follows:
6 mm
7. SKIP THE REST of the steps of ITALERI kit manual.
Chassis assembling
3
R 1
R11 R12 Icm51Icm51 Icm39Icm39 Icm40
R11 R12 Icm51Icm51 Icm39Icm39 Icm40
4
Icm9
R1
Icm49
Icm47
Icm12
Icm19
R15
Icm38
Icm38
Icm38
R13
Icm46
Icm46
R14
Icm45
Icm45
Icm48
Icm50
Icm19
R10
Loading...