Page 1
Ò
WinFast
QUICK INSTALLATION GUIDE
Digital TV Card
CODE: LR 66xx
P/N: W05G0060
Ver: B
Page 2
Table of Contents
Connect Input & Output Devices ........................... 1
Board Layout ........................................................... 2
Hardware Installation .............................................. 4
Driver & Application Installation ............................ 5
Recycling Information ............................................. 8
Page 3
If you are using an active antenna, please set
the jumper, as circled in the photo to the right,
to the enabled position. Otherwise, please
leave it at the disabled position (default).
VCR
Input sources
DVD/VCD Player
CCD cameraCCD camera Camcorder
SELECT START
ANALOG
SONY
PlayStation
Video Game Console
5
4
3
2
1
RF input
RF output
Composite Video input
S-Video input
IR sensor connector
Connect Input & Output Devices
From DVB-T
Antenna
S-Video out
S-Video in
Composite
Video out
Composite Video in
5
4
3
2
1
IR sensor
To other DVB-T
device
RF input
RF output
Sound card line in
(Blue)
Sound Card
Audio out
Jumper
DTV1000 T
1
Note:
The diagram is for reference only. The actual board appearance may differ from the
diagrams.
Page 4
VCR
Input sources
DVD/VCD Player
CCD cameraCCD camera Camcorder
SELECT START
ANALOG
SONY
PlayStation
Video Game Console
PC Monitor
Remote
Control
Remote control
Video In
Audio out
Audio in
S-Video
out
Composite
Video Out
Cable TV provider
From Antenna
FM Antenna
Board Layout
From Cable TV
DTV2000 H
FM
AIR ANT
CABLE
REMOTE
AUDIO IN
VIDEO IN
2
Note:
1. The diagram is for reference only. The actual board appearance may differ from the
diagrams.
2. FM and Remote Control functions are optional. Please refer to the descriptions
on the retail box for detailed product specifications.
Page 5
Cable TV provider
From Antenna
(Digital or Analog)
From Cable TV (Analog)
FM
AIR ANT
CABLE
REMOTE
AUDIO IN
VIDEO IN
Note:
For Antenna: It can be connected to both digital and analog TV signal.
For Cable TV: Only analog TV signal can be received by the cable (Digital
cable TV signal is not supported).
(1) If you have an antenna (digital) and a cable (analog), please
connect the antenna to an antenna connector, and cable to a cable
TV connector.
(2) If you have only cable (analog), please connect it to the cable
connector.
(3) If you have a VHF/UHF antenna that covers all local digital/analog
channels, please connect it to the antenna connector in order to
switch between digital and analog TV. An example of this is seen in
Australia.
Below is a detailed descriptions on the connecting devices of WinFast
DTV2000 H.
3
Board Layout
Page 6
Step 1:
Power off your PC. Open the computer case. Remove the coverplate
of an unused expansion slot.
Step 2:
Align the bus on the card with the PCI slot.
Step 3:
Gently press the WinFast TV device down into the slot until you feel
the edge of the bus reaches the bottom of the PCI slot. Note that the
capture card can be inserted into PCI slot in one direction only.
Step 4:
Secure the bracket of the card to your computer case with the screws.
Then fit the computer case cover back in place.
Step 5:
Connect the input sources and output devices to your capture card
following the instructions given in Connect Input and Output
Devices section on the next page. Now you are ready to connect the
video sources to your capture card.
Hardware Installation
4
Page 7
Step 1:
Turn on your PC and start up the
Windows.
Step 2:
Shortly after entering the Windows ,
you will see the Found New
Hardware Wizard dialog box. Click
"Cancel".
Step 4:
Click on the Driver item to begin the
installation.
Step 5:
The wizard is extracting the files
needed for the installation. There is
a progress bar indicating the status.
Step 3:
Insert the Multimedia Software CD
into your CD-ROM drive. Autorun
will start and the menu screen will
appear as the figure shown to the
right. Click the button marked
WinFast TV Capture Card on the
virtual remote control.
Driver & Application Installation
5
Page 8
Step 6:
You have to choose a language for
the installation. Make the selection
and click OK.
Step 7:
The wizard is ready to install the
WinFast Entertainment Center.
Step 8:
The installation is going to start.
Click Next.
Step 9:
The wizard will install the software
for the hardware. Check "Install the
software automatically
(Recommended)" and Next.
Driver & Application Installation
6
Page 9
Step 10:
The wizard has finished installing the
software. Click Finish.
Step 11:
You have to restart your computer.
Click Finish to reboot.
Step 12:
After reboot, the wizard will take
care of the rest of the installation
process.
Step 13:
The entire installation is completed.
Now you are able to use WinFast
DTV1000 T/DTV2000 H TV Card.
Get ready for the high quality digital
TV programs on your computer.
Driver & Application Installation
7
Page 10
Thank you for choosing this Leadtek product.
WinFast TV Device is an electronic device which may contain
hazardous materials/components which need to be disposed of
properly at the end of the product's life. You can help avoid hazardous
risks by not disposing of the electronic device in your normal domestic
waste. Electric and electronic devices are marked with a rubbish bin
with a diagonal line through it, which indicates that these products
should not be thrown out with usual domestic waste. If such products
are disposed of together with domestic waste, electric and electronic
equipment may have severe impacts on the environment as well as
on human health, not least because of the potentially hazardous
materials.
Pursuant to the ElektroG, Leadtek provides an easy and convenient
way of recycling electric and electronic equipment. Please dispose of
your electric and electronic equipment at your local collection site
specially designated for this type of waste. Such disposal is free-ofcharge to you. Together with the management of the local collection
site, Leadtek will then take care of the efficient recycling and treatment
of the electric and electronic waste.
Recycling Information
8
Loading...