LEADER PREMIUMS AB0073 User Manual

Roche Multifunctional

Wireless Charging Stand

Instruction Manual

7141-73

10

Features:

1.

Wireless Charging Surface

2.

Foldable Phone Stand

3.

3-in-1 Charging Cable

USB Input Tip

4.

5.

2-in-1 Charging Tip

6.

Type-C Charging Tip
LED Indicator

7.
Micro-USB Input Port

8.
Charging Cable Storage Compartment

9.
LED Flashlight

10.

11.

What’s included:

1 x Wireless Charging Stand
1 x Instruction Manual

1 x 3-in-1 Charging Cable

•

Input power: 5V/2A
Micro-USB input: 5V/1A

•

•

Wireless Charging Output: 5V/1A

INSTRUCTIONS:

1.

Wireless Charging Function:

•

Remove the 3-in-1 charging cable(3) out
from the cable storage compartment of the
wireless charging pad.

•

Once removed, connect the USB input
tip(4) to the appropriate power source and
the 2-in-1 charging tip(5) to the Micro-USB
input port(8) of the wireless charging pad.

•

11

Once connected, the LED indicator will glow
WHITE, then light off to indicate in standby

mode and is ready to begin charging.

•

Place the wireless charging supported
device on the charging surface(1),the
device will begin to charge automatically.
(LED will glow WHITE when device is
charging).

**

Note: When wireless charging, if the LED

is either NOT a wireless charging device
or there is an object between the device
and charging surface interfering with the
charging process.

2.

Wireless Charging Pad - Phone Stand:

•

As shown below the wireless charging pad
is able to be fold open to be used as a
wireless charging phone stand.

SAFETY PRECAUTIONS:

WARNING-When using this product, basic

•

precautions should always be followed:
Read all the instructions before use.

1.
Never store or use this product in

2.
temperatures below 32°F (0°C) or above
115°F (45°C).
Do not overcharge your phone. The

3.
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.
To reduce the risk of injury, close

4.
supervision is required when the product is
used near children.
Do not expose the device to moisture.

5.
Do not use the device in excess of its

6.
output rating. Overload outputs above the

Do not use the device if damaged or

7.

8.

explosion or risk of injury.
Do not disassemble the device. For

9.

professional. Incorrect reassembly may

10.

or temperatures above 104°F (40°C) may
result in explosion.
To ensure product safety, ensure that

11.

identical replacement parts.
Attachments on the back of your phone

12.

wireless charger, and lead to overheating.
Please remove attachments from the

phone before charging on this device.

FCC Statement:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful

(1)

interference, and
This device must accept any interference

(2)

received, including interference that may
cause undesired operation.

Warning:

*

approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.

FCC Warning Statement

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment. This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.
‐ Consult the dealer or an experienced radio/TV technician for help.

MADE IN CHINA