LEADER PREMIUMS AB0028 User Manual

Ozone Wireless Charging Pad

with Dual Outputs

Instruction Manual

AB0028

1.

Charging Pad Surface

2.

USB Output Port (2)

3.

LED Indicator

4.

Micro-USB Input Port

What’s included:

1 x Wireless Charging Pad
1 x USB to Micro-USB Charging Cable
1 x Instruction Manual

Input power: DC 5V/2000 mA

•

Output power: 5W

•

Product size: 98x 98 mm

•

Dual USB Outputs: DC 5V 1A/1A

•

30 cm standard Micro-USB cable

•

INSTRUCTIONS:

1.
Connect the provided Micro-USB cable to

a.

the USB plug adapter.
Connect the Micro-USB tip to the input port

b.

on the charging pad.

Charging Mobile Devices:

2.
Ensure that your phone or tablet supports

a.

wireless charging. It will be listed in the

b.

Place the enabled device on the surface
of the wireless charging pad. The device
should display charging indicator.
When completely charged, remove the

c.

device from the charging pad.

d.

Or Insert corresponding charging cable into
the Charging Pad USB port to charge your
devices normally.

*

Note: To charge devices, use only the
accessory cable or the cable included with
your own device by the manufacturer.

SAFETY PRECAUTIONS:

Read all the instructions before using the
product.

WARNING-When using this product, basic

•
precautions should always be followed:

1.

Read all the instructions before use.
Never store or use this product in

2.
temperatures below 32°F (0°C) or above
115°F (45°C).

3.

Do not overcharge your phone. The
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.

4.

To reduce the risk of injury, close
supervision is required when the product is
used near children.
Do not expose the device to moisture.

5.

Do not use the device in excess of its

6.
output rating. Overload outputs above the

Do not use the device if damaged or

7.

8.

explosion or risk of injury.

9.

Do not disassemble the device. For repairs,

Incorrect reassembly may result in a risk of

10.

or temperatures above 104°F (40°C) may
result in explosion.

11.

To ensure product safety, ensure that

identical replacement parts.

12.

Attachments on the back of your phone can
impede the effectiveness of the wireless
charger, and lead to overheating. Please
remove attachments from the phone before
charging on this device.

FCC Stat eme nt:

This device complies with Part 15 of the FCC

•
Rules. Operation is subject to the following
two conditions:
This device may not cause harmful

(1)

interference, and
This device must accept any interference

(2)

received, including interference that may
cause undesired operation.

Warning:

*

approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.

FCC Warning Statement
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.This
equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV
technician for help.

Made in China