Leader Light LL50 450 User Manual
USER MANUAL
LL PRO GRAPHIC PANEL
Leader Light s.r.o.
M.Gorkeho 33
SK-052 01 Spisska Nova Ves
Slovakia
www.leaderlight.eu
LL50 450
All dimensions are in millimeters
ENVIRONMENT
Do not throw away the appliance with the normal household waste at the end of its life,
but hand it in at an ofcial collection point for recycling. By doing this, you help to preserve
the environment.
WARNING!!!
Carefully read before installing, powering or servicing.
Nothing to do if anything misunderstand! Installation can be done only
by a qualied professional in accordance with relevant local codes.
01 SAFETY INFORMATION
01.1 Risk of eyes damage
Do not look directly into LED lamps.
Do not look into light beam from a distance of less than 40 cm (16 inches)!
-
-
01.2 Protection from electric shock
Shut down power before installation or maintenance.
Luminaries and recommended AC power supply must be installed by a qualied professional
in accordance with relevant local codes. Only acceptable source of AC power and frequency
that complies with local building and electrical codes to use.
Do not use or do not connect the products if the power cable, power plug or xtures are any
way damaged, wet, or if they are overheating.
Do not modify, alter, or attempt to service the LeaderLight appliance. Doing so will void the
warranty.
Before removing or installing any cover or part of appliance disconnect it from AC power.
Appliance always connect to earth (eltech.).
-
-
-
-
-
-
01.3 Fire prevention
Follow all safety consideration.
Thermostatic switches or fuses never to bypass.
Device never shield – minimum distance around tting must be 100mm (4 in.).
LEDs never direct cover with lters or other materials.
Allowing max. ambient temperature is 40°C (104°F).
-
-
-
-
-
02 PRODUCT SPECIFICATION
02.1 Technical Specication
LED INDICATION STATUS
POWER (Red) blinking – 2Hz OK - inside xture is everything correct
DATA (Green) light off NO DMX512 signal
DATA (Green) blinking – 4Hz OK- income correct DMX512 signal
DATA (Green) fast blinking NON correct digital signal
POWER (Red)
alternate blinking Autotest function
DATA (Green)
Control LEDs Indication
POWER DATA
03 INSTALLATION
03.1 Unpacking
Unpack carefully.
This is electronic equipment and should be handled carefully.
Damaged delivered package or if are any mechanical parts broken – it must be claim
immediately by the transport company. Photo pictures as evidence are valuable for
future claim.
-
-
-
03.2 Physical installation
Loading capacity of bearing area has to be at least 10 times the weight of all device
clusters (luminaries, clamps, cables, ...).
Hairbreadth from combustible materials is 0,5m.
The LL PRO GRAPHIC PANEL is designed for use in a 600mm grid suspended
ceiling with T prole (Figure Nr. 1.1) or surface installation by LL HOLDER GRAPHIC
PANEL LL41 605 (Figure Nr. 1.2).
-
-
-
©MMX - Leader Light – All right reserved
02.2 Data and Power connections
If you have any question please, contact support@leaderlight.sk
COMPLIMENTS ON YOUR PURCHASE!
Content:
01 SAFETY INFORMATION
01.1 Risk of eyes damage
01.2 Protection from electric shock
01.3 Fire prevention
02 PRODUCT SPECIFICATION
02.1 Technical Specication
02.2 Data and Power connections
02.3 Top panel
03 INSTALLATION
03.1 Unpacking
03.2 Physical installation
03.3 Connecting to AC power
03.4 Control data connecting
03.5 DMX channels
04 MAINTENANCE
Edition: A - 2010
DMX Out
XLR-5pin
DMX In
XLR-5pin
Power Out
PowerCon
Power In
PowerCon
Dip options
Rotating DIP address 000÷511
“100“ “10“ “1“
Control LEDs
POWER DATA
MODE & ADDRESS
02.3 Top panel
Lamp type: 144 x RGB TOP LED *
Lifetime: Long 100 000 hrs 60% degradation
Control data Input: DMX512 In/Out with XLR 5pin
Input power: max.60W
Power connection: 100-260V AC In/Out PowerCon
Net weight: 6kg
IP: IP20
Ambient temp. (Ta):
Maximum 40°C
Cooling: Conventional
Materials and nish: Housing: anodized aluminium black
Cover: plexiglass with special diffuse foile
Installation: Surface, recesed or semi-recesed mounting
129,5
588
588
* TOP LED: R-Red, G-Green, B-Blue
Following items are included:
- LL PRO GRAPHIC PANEL RGB 1 pc.
- PowerCon type “A“ + “B“ 1 pc.
- User manual 1 pc.
Additional items needed:
- Data cables with XLR 5pin Female/Male 1 pc.
- Controller compatible with DMX 1 pc.
Surface mounting:
- LL HOLDER GRAPHIC PANEL SURFACE
1 pc.
- Screws and washers M12 4 pcs.
03.5 DMX channels - subject to change
The latest version of DMX channels appendix are on the websites - www. leaderlight.eu
Custom made solution for example:
-
-
If you have any question please, contact support@leaderlight.sk
04 MAINTENANCE
To tackle all Safety Information- 01!
Damage caused by inadequate cleaning or maintenance is not coverd by warranty.
Regular cleaning is demand (dust, dirt, ...)
Maintenance policy:
Unplug mains before maintenance and at least 10 minutes cool off
Appliance do not illegal open or demount
Clean-up dust only from outer surface (for ex. scuttle, diffuser and lenses).
Use vacuum or dumpy duster (warm water)
Before reinstalling to check failure-free state – no wet parts!
-
-
-
-
-
-
-
-
03.4 Control data connecting
Control data cable length is specied by Norm IEC929 Annex E4
It is not necessary to open the xture before connecting of DMX512 control signal.
Interconnections are realized by Neutrik XLR 5pin In/Out connectors.
-
-
03.3 Connecting to AC power
To tackle all Safety Information- 01!
For protection from electric shock, the device must be grounded (earthed)!
It is not necessary to open the xture before power supply.
Power supply is solved simple with Neutrik PowerCon connectors.
The xture is equipped with auto-switching power supply that automatically adjusts to
any 50-60Hz AC power source from 100-260V.
Cord plug connections:
-
-
-
-
-
-
Symbol Pin Wire Colour Screw (US)
L live brown/black black
N neutral light blue white
ground (earth) yellow/green green
1.1
insert into suspended
ceiling with T prole
100-260V AC
In/Out Power Con
Control data In/Out XLR 5pin
Order code Product name
LL50 450 LL PRO GRAPHIC PANEL RGB **
Accessories:
LL41 605 LL HOLDER GRAPHIC PANEL SURFACE
** Total 6*6 100mm pixel
Functions Dip ( switch Dip1, Dip2, Dip3, Dip4 ):
Dip1 Dip2 Dip3 Dip4
off off off x ModA 108ch (6x6xRGB)
off off on x ModB 3ch (paralel RGB)
off on off x ModC 180ch (6x6x RGBAW)
off on on x ModD 5ch (paralel RGBAW)
on off off x ModE 144ch (6x6x RGBA)
on off on x ModF 144ch (6x6x RGBW)
on on off x ModG 110ch (6x6x RGB + 1x WA)
on on on x ModH 110ch (6x6x RGB + 1x AW)
x x x on future
Example ModA:
1-3 ch.
RGB
4-6 ch.
RGB
7-9 ch.
RGB
10-12 ch.
RGB
13-15 ch.
RGB
16-18 ch.
RGB
19-21 ch.
RGB
22-24 ch.
RGB
25-27 ch.
RGB
28-30 ch.
RGB
31-33 ch.
RGB
34-36 ch.
RGB
37-39 ch.
RGB
40-42 ch.
RGB
43-45 ch.
RGB
46-48 ch.
RGB
49-51 ch.
RGB
52-54 ch.
RGB
55-57 ch.
RGB
58-60 ch.
RGB
61-63 ch.
RGB
64-66 ch.
RGB
67-69 ch.
RGB
70-72 ch.
RGB
73-75 ch.
RGB
76-78 ch.
RGB
79-81 ch.
RGB
82-84 ch.
RGB
85-87 ch.
RGB
88-90 ch.
RGB
91-93 ch.
RGB
94-96 ch.
RGB
97-99 ch.
RGB
100-102 ch.
RGB
103-105 ch.
RGB
106-108 ch.
RGB
1.2
Surface installation with LL41 605
hang up tting
100-260V AC
In/Out Power Con
Recessed mounting in 600mm suspended ceiling with T prole
Loading...