Leader Light LL46 400 User Manual

Leader Light s.r.o.

SK-052 01 Spisska Nova Ves

M.Gorkeho 33

Slovakia

www.leaderlight.eu

USER MANUAL

LL PRO LED SPOT DC24V Z-POWER OneChip RGB

LL46 400

COMPLIMENTS ON YOUR PURCHASE!

01 SAFETY INFORMATION

WARNING!!!

Carefully read before installing, powering or servicing.
Nothing to do if anything misunderstand!
Only for professional use!

01.1 Risk of eyes damage

03 INSTALLATION

03.1 Unpacking

- Unpack carefully.

- This is electronic equipment and should be handled carefully.

- Damaged delivered package or if are any mechanical parts
immediately by the transport company.

Photo pictures as evidence are valuable for future claim.

03.2 Physical installation

Loading capacity of bearing area has to be at least 10 times the weight of all device clusters

-
(luminaries, clamps, cables, ...).

- Heigrbreadth from combustible materials is 0,5m.

broken – it must be claim

All dimensions are in milimeters

max.121

Φ

120

- Do not look directly into LED lamps.

- Do not look into light beam from a distance of less than 40 cm (16 inches)!

01.2 Protection from electric shock

max.196

- Shut down power before installation or maintenance.

- Luminaries, Drivers and recommended power supply must be installed by a qualified professional in

accordance with relevant local codes.
Only acceptable source of AC power and frequency that complies with local buidling and electrical
codes to use.

- Do not use or do not connect the products if the power cable, power plug or fixtures are any way

damaged, wet, or if they are overheating.

- Do not modify, alter, or attempt to service the LeaderLight appliance.
Doing so will void the warranty.

Following items are included:

- LL PRO LED SPOT with 5 m cable and XLR 6PIN connector 1 pc.

- User manual 1 pc.

Additional items needed:

- LL PRO LED Z-POWER DRIVER

- DMX controller

Content:
01 SAFETY INFORMATION

01.1 Risk of eyes damage

01.2 Protection from electric shock

01.3 Fire prevention

02 PRODUCT SPECIFICATION

02.1 Technical Specification

03 INSTALLATION

03.1 Unpacking

03.2 Physical installation

03.3 Connecting to AC/DC power supply

04 MAINTENANCE

ENVIRONMENT

Do not throw away the appliance with the normal household waste at the end of its life,

but hand it in at an official collection point for recycling. By doing this, you help to preserve

the environment.

©MMVIII - Leader Light – All right reserved If you have any question please, contact [e-mail]

- Before removing or installing any cover or part of appliance disconnect it from AC power.

01.3 Fire prevention

- Follow all safety consideration.

- Thermostatic switches or fuses never to bypass.

- Device never shield. Around the axis of the fitting (180°) must be maintained space for cooling.
Minimum distance from the surrounding objects must be 50mm (2 in.) (figure 1.1).

- LEDs never direct cover with filters or other materials.

- Allowing max. ambient temperature is 40°C (104°F).

- Luminaries never use without mounting brackets. The housing never install directly to the surface.

02 PRODUCT SPECIFICATION

02.1 Technical Specification

Lamp type:

Lifetime:

Control data Input:

Input power:

DC Power Connection:

Net weight:

Dimensions LxHxΦ:

Ambient temp. (Ta):

Cooling:

Materials and finish:

Installation:

12xRGB 3x1W P5
(Red, Green and Blue)

Long 60 000 hrs 60% degradation

Optic:

35mm standard 25°
optional 40°- on request

3 channels 24V dimming

max. 50W

24V DC 5m cable with XLR 6PIN

2,5kg

max. 121mm x max. 196mm x 125mm without bracket

IP:

IP65

Maximum 40°C

Conventional

Housing: powder-painted anodized aluminium in black
(other colours on request)
Cover: clear or frosted PMMA

Any position for ceiling, wall and surface mounting

Edition: A - 2008

03.3 Connecting to DC power supply

- To tackle all Safety Information- 01!

- You can suffer a dangerous electric shock by using a high voltage AC/DC power
supply - by touching AC/DC power supply the wires inside the unit!

- LL PRO LED SPOT operate with the LL PRO DRIVER
IN:100-260AC/ OUT: 24V (Figure Nr. 2.1, 2.2).

- It is not necessary to open the fixture before connecting to LL PRO DRIVER.

- Pull the XLR 6PIN cable connector from fixture to the LL PRO DRIVER.

AC Power Supply Cord plug connections to LL PRO DRIVER:

Symbol Pin Wire Colour Screw (US)

L live brown yellow or brass

N neutral blue silver

ground (earth) yellow/green green

04 MAINTENANCE

- To tackle all Safety Information- 01!

- Damage caused by inadequate cleaning or maintenance is not coverd by warranty.

- Regular cleaning is demand (dust, dirt, ...).

Maintenance policy:

- Unplug mains befor maintenance and at least 10 minutes cool off.

- Cleanup dust from cover.

- Use dampy duster (warm watter).

- Before reinstalling to check failure-free state – no wet parts!

Order code Product name Current

LL46 400 LL PRO LED SPOT OneChip RGB 3x0,7A

LL PRO LED SPOT connecting to PWM DRIVER 12

DC 24V

LL PRO LED SPOT connecting to PWM DRIVER 36

DMX

CONTR.

4 GROUPs: XLR 6PIN

max. 12A

DRIVER 12

100-260V AC

3 x 4 GROUPs: XLR 6PIN
max. 40A

Detail: LL PRO LED DRIVER 12

2.1

INSTALLATION

Ventilation space 180° free

minimal.

50mm

Minimal mounting distance from surface

WARNING!!!

!!

Non-minimum distance and / or
non-use the original brackets is
at your own risk!

minimal.

50mm

Ventilation space 90° free

minimal.

50mm

minimal.

100mm

1.1

MOUNTING

90°

Aiming possibility

The fixture could be aim to wish position with

bracket.

DC 24V

DMX

CONTR.

Detail: LL PRO LED DRIVER 36

DRIVER 36

100-260V AC

2.2

If you have any question please, contact [e-mail]