Page 1
EH-35MP3
User manual
INTRODUCTION .......................................................................................... 2
FEATURES ........................................................................................................ 2
SPECIFICATION .................................................................................................. 2
PRODUCT DETAILS .................................................................................... 3
PACKING LIST ................................................................................................... 3
FRONT VIEW ..................................................................................................... 4
BACK VIEW ..................................................................................................... 5
REMOTE CONTROL ............................................................................................ 6
BASIC OPERATION .................................................................................... 7
REQUIREMENT FOR SYSTEM OF SOFTWARE& HARDWARE ....................................... 7
PARTITION AND FORMAT OF DISK DRIVER ............................................................... 7
CONNECTION AND USAGE OF THE PRODUCT ............................................................ 9
CONNECTION GUIDE .............................................................................. 11
OPERATION OF PRODUCT USAGE ...................................................... 15
PICTURE PLAYING ........................................................................................... 15
MUSIC PLAYING .............................................................................................. 15
1
Page 2
MOVIES PLAYING ............................................................................................ 15
DVD PLAYING .............................................................................................. 16
SYSTEM SETUP .......................................................................................... 16
MAINTENANCE NOTICE ......................................................................... 18
FAQ ................................................................................................................ 18
OTHERS ........................................................................................................ 19
Introduction
Features
Thank you for choosing EH-35MP3 by LC-Power. It can store and play many kinds of
multimedia files. The product features many different connectors and can show you
pictures and videos in high definition.
Specification
Hard disk support Standard SATA 3.5” Hard Drive
USB host Support multiple USB storage
USB port USB 2.0 high speed port
video output Composite video /component video/HDMI
Audio output Stereo/digital HDMI
Audio Format: MP3, WMA, WAV, AAC
Video Video decoding: MPEG 1/2/4, Divx,Xvid
Format: AVI,VOB, DAT, MPG, MPEG
Subtitle SSA, SMI, SRT, SUB
Picture JPG/JPEG
Picture play mode Slide show
2
Page 3
Power adapter AC input 100V-240V, 50/60HZ
DC output 12V, 2A
Dimension
171×110×47mm
Weight Approx. 460g (without hard disk drive)
Note: Up to improvements, the appearance and specification might be changed
accordingly without prior notice.
Product details
Packing list
Check the accessories after receiving the product. If there are any parts missing, please
contact your dealer immediately.
No. Name Quantity
1 Media player 1 pcs
2 Power adapter 1 pcs
3 Remote control 1 pcs
4 AV cable 1 pcs
5 YPbPr cable 1 pcs
6 USB cable 1 pcs
7 User manual 1 pcs
8 Batteries 2 pcs
9 Screws several
3
Page 4
IR
Page 5
Page 6
Remote control
BUTTON FUNCTION
POWER
Turn on and off and set to standby mode
MUTE
Turn on or off audio output
SETUP
Enter the menu
TV OUT Press to switch between SD PROSCAN, 720p , 1080i
MODE When playing a picture SlideShow, it changes the transition
mode between pictures.
SUB-T Selection key for MPEG4 subtitle file. It activates and
deactivates the subtitles while video playing. Use the up button
or down button to select a subtitle language that is available
on the DVD.
ANGLE Rotates the images. Select to view the same scene from
different angles, if the DVD has been recorded with multiple
angles.
ZOOM
Press to zoom when playing back photos or video programs.
Open or close the image scaling function.
Previous.
Next.
Skip backward.
Skip forward.
VOL+ Increase the volume.
VOL- Decrease the volume.
Stop.
Pause/play.
ENTER Enter.
Up
Down
Left
Right
DVD play Use the DVD key to enter into the DVD navigation function.
MEDIA TYPE Pressing once it returns to the main menu from the Picture,
Video or Music section. Pressing twice returns to the storage
unit menu (if there is more than one).
INFO Display information of the media file. In DVD mode, select the
button to display the time, title or chapter on playing.
AUDIO Switching the audio channel.
PREVIEW ON/OFF Be able to select preview on or preview off in file mode.
REPEAT Change repeat play mode.
SLIDE SHOW Plays pictures in continuous mode.
6
Page 7
Basic operation
Requirements for software & hardware
Hardware
PC and notebooks
Software
Windows 2000 / Windows XP / Windows Vista
Please choose the right disk drive suitable for your product and install the disk drive
based on the requirements shown in the user manual of the disk drive. You can also
ask your dealer about the installation methods.
Partitioning and formatting of the disk drive
NOTE:
The product can’t be recognized by the PC if an unformatted hard disk is totally new.
Please partition and format the hard disk first before you use it.
A re-formatting job needs to be done for the file format for some old hard disks to
make sure the product is workable.
Please note that every time partitioning and formatting will delete all the data of the
hard drive. We recommend to backup previously existing data.
Partitioning and formatting under Windows 2000 / Windows XP / Windows Vista
To make sure that the product can work normally, it is necessary to partition and format
the hard disk before first use. Please operate strictly according to the instructions. For
any doubt about the practical operation, please contact your dealer or our after sales
service department for further help.
A. Startup the operation system of Windows and make sure that the system is
working in a normal status.
B. Connect the product with the PC:
7
Page 8
For models with power adapter, please plug the adapter into the DC IN port.
Please connect the product to the PC through USB cable.
C. Once the product enters the working status, the indicator will turn on. The system
green icon appears on the lower right corner.
D. Right click ”my computer”, select the “management” option and open the window
of “hard disk management”.
E. Please select the “hard disk management” option under the directory of “storage”
of the console in the right corner. It is able to find a note of “unknown” in the hard disk
management information directory.
F. Right click the area of “unknown” on the hard disk and click the “signature” option.
G. Check the hard disk and click “sure” in the window of “write signature”.
H. The “unknown” prompt of hard disk disappears and a “basic” prompt status
appears. Now it is able to start the partitioning and formatting operation.
I. Right click the chart of “unassigned” and select the “create hard disk partition”
option.
J. Enter “creating hard disk partition guide” and click “next step” to continue.
K. Please select the option of “main hard disk partition” in the “select partition type”
and then click “next step” to continue.
L. At the “assign the partition capacity” please install the value defaulted by the
system and then click “next step” to continue. When only one partition is needed,
please set the capacity of the first partition and then click “next step” to continue
when you need more than one partition.
M. Keep the value defaulted by the system to assign the size number for the hard
disk and then click “next step” to continue.
N. In the formatting partition
please set the option of ” FAT32 or NTFS” in the option of using file system;
check the option of “run fast formatting” and then click “next step “ to continue.
O. Click “finish” to complete the guide
for one partition only, the process is complete and the product is available to use
for more than one partition, the process completes the partitioning / formatting of
the “main hard disk”, please then follow the operation for further partitions.
P. Right-click the residual area of “unassigned” and select the option of “create hard
disk partition”.
Q. Please click the option of “expand hard disk partition” and then click “next step” to
8
Page 9
continue.
R. Select Windows default in “unassigned partition”.
S. Click“finish”.
T. Right-click the interface of the created expanded hard drive.
U. Select the option “to create a logic disk”.
V. Keep the option of “logic disk” defaulted by the system and then click ”next step”
to continue.
W. In the “assign the partition” area
please click ”next step” to continue, if you only need one logic partition
please assign the capacity of the first partition and then click ”next step” to
continue, if you need more than one logic partition.
X. Keep the option of “assign the disk symbol” defaulted by the system, click “next
step” to continue.
Y. In the “format partition” area
select “FAT32 or NTFS” in the option of ”using file system”
select the option of “implement fast formatting” again and click ”next step” to
continue and click ”finish”.
Z. The created disk can be browsed in the “computer management” respectively in
“my computer” and can be used for reading/writing operations after finishing the
partitionion and formatting operation.
Connection and usage of the product
This product has an USB interface, so it can support hot plug & play.
In a Microsoft operation system:
A. Startup the PC
Make sure that the PC works normally.
B. Connect the USB cable:
Plug one end of the cable into the players' USB interface.
Plug the other end of the cable into the USB port of the PC.
C. Connect the power cable.
D. Indicator of the product turns on.
9
Page 10
This indicates that the products is on working status.
E. With an active system, the green icon of disk appears.
The new hardware is found by the system.
The green arrowhead icon appears on the lower right corner of the screen and the
products is recognized by the operation system.
F. Open ”my computer”, the new ”disk partition” appears.
The disk symbol should be the next letter following for previously existing
partitions, e.g. E:/.
The speed of the disk symbol appearing may vary due to the performance of your
computer.
G.Common usage
The operation is handled the same way as common hard disk accessing, reading
and writing.
The product indicator flickers during the reading and writing process.
The product indicator stops flickering or slows down flickering during no reading or
writing operation and standby status
Please don’t draw out the product from the PC when the product is under reading
or writing status. Otherwise it may cause damage to the hard disk or loss of data.
Exit and draw out the product
As an USB interface, it supports hot swap. Please follow the procedure below to make
sure a normal exit from the system happens and to protect the system and the safety of
the product.
In a Microsoft operation system:
A．Make sure the product is not under reading or writing status.
No reading or writing operation command has just been executed.
No flickering on the product indicator.
B．Click the green icon on the lower right of the system screen.
The option of connected USB device directory appears.
C．Click the device needed to exit.
D． The system will prompt: remove the device from the system safely.
10
Page 11
E
F
1
2
Page 12
Page 13
Page 14
Notes:
1. Please don’t power off when the device is connected to the PC for reading and
writing.
2. If there is no USB device detected after connecting the device via an USB
cable, maybe the PC is operating another program, then please pull off the USB
cable and wait about 10 seconds, then connect again.
Operation of product usage
Power on the HDD player, the system shows the main menu of storage equipment after
a few seconds. There are two or more partitions in on the HDD.
Press the up and down key to choose the equipment or the partition and press the
ENTER key to enter the menu.Then press the left or right key to choose which you like.
By pressing ENTER, you could enter the corresponding menu:
Picture Playing
On main menu, press the direction key, you can choose the picture file, if you press the
ENTER key, it will begin to play normally. Press the MODE key on the remote control to
choose Slide mode.
Music playing
If you press the direction key on the remote control, you can move a highlight line to
select the navigation function, then the navigation menu will be displayed on the TV
screen. Press the direction key to select music and press the ENTER key to enter music
EQ and begin playing. The media player can display song lyrics and output the sound
signal at the same time under playing the song files of MP3 and WMA format. The song
lyrics of LRC will auto-display when the LRC file and song file are in the same folder
and the two files name must be the same.
14
Page 15
Movies playing
Select “movies” in the main menu, you can move a highlight line to select the navigation
function, then the navigation menu will be displayed on the TV screen. Press the
direction key to select movies and press the ENTER key to play.
MPEG4 Subtitle Operation:
Put subtitle file and video file in the same folder in the file library, first press SUB-T key
to choose the subtitle file, then choose the according video file and press the enter key
to play both.
DVD playing
Press the DVD button on the remote control, you can move a highlight line to select the
navigation function, then the navigation menu will be displayed on the TV screen.
Example:
a. Connect the player via USB to the computer. You will be able to see the content of
the HDD on your computer (“my ccomputer”).
b. Create a folder on the HDD of the player. Copy all files of the source DVD or source
folder on your computer's HDD into the new folder.
c. Disconnect the USB cable and connect the player to your TV.
d. Activate the file manager, choose the new folder and press the DVD PLAY button.
The movie playback starts.
Note: All content of the DVD must be copied to the new movie folder on the player's
HDD, including the empty folder (e.g. “audio_ts”), otherwise playback might not work
properly.
SYST E M S ETU
15
Page 16
SYSTEM SETUP
Press the SETUP key to access the system setup menu.
System setup options
SETUP Project set Detailed settings menu
GENERAL
SETUP
OSD language English, French, German, Italian,
Swedish, Danish, Spanish
Screensaver ON or OFF
TV type Multi.System, NTSC, PAL.
a. NTSC (Taiwan, USA, Japan etc.)
b. PAL (Europe, mainland China and
other countries)
Video output SD PROSCAN, 720p, 1080i
Default setting is the SD PROSCAN
mode, AV, YPBPR, HDMI output at the
same time. If selecting the 720p or 1080i
mode, YPBPR and HDMI output are at
the same time, AV-free output.
Advice: If your TV support the YPbPr or
HDMI display mode, use this mode to
watch.your material.
Defaults Reset.
To restore the factory settings.
16
Page 17
AUDIO
SETUP
SELECT AUDIO
OUTPUT
Analog.
The use of AV and YPBPR analog audio
output.
SODIF/RAW.
The use of Coaxial and HDMI digital
audio output.
SPDIF/PCM.
The use of Coaxial and HDMI digital
audio output.
PREFERRED AUDIO
LANGUAGE
English, French, Spanish, German, Italian
PHOTO
SETUP
SLIDE Time 5sec, 10sec, 15sec. Set the speed of
browsing pictures.
SLIDE Mode LR to Center, Center to LR, Edge to
Center, Side L to R, Fade Out In,
Random, Top to Bottom, Bottom to Top,
TB to Center, Center to TB, Side TB, Left
to Right, Right to Left
VIDEO
SETUP
Subtitle English, French, Spanish, German,
Italian, OFF.
Maintenance notice
To protect the normal use of all accessories, please kindly make sure to understand and
pay attention to the following points.
The power input is 100V~240V, output 12V/2A.
Under normal working status, the power adapter will warm up, a body temperature of
60 degree or below is normal.
Please be sure of aeration under normal working status, do not put the device in your
bed, a sofa or similar areas where the cooling effect is not good enough.
Please do not open the device yourself. In case of a defect contact your dealer about
it. Avoid any danger of an electronic shock.
Please pull out the cable and shut the device immediately if the cable is broken or
liquid has been spilled in or over the device; then contact your dealer.
17
Page 18
FAQ
Q:The hard disk can not be recognized under Windows 2000 / Windows XP operation
system.
A: It may be caused by the original USB driver being lost or not installed properly (e.g.
Windows XP needs Service Pack 1 for a proper USB device handling). Make sure to
keep your operating system up to date.
Q: The hard disk is available but the speed is very slow and it takes a long time to copy
data.
A: Please check the USB terminal version of the PC and update your drivers.
Q: Can data be copied between the HDD and a peripheral USB device?
A: No, it can’t.
Q: When I try to disconnect the USB device, I keep on getting the “Device generic
volume cannot be stopped right now. Try stopping the device again later” message,
what should I do?
A: Close any program that might be accessing data on the player, including Windows
®
Explorer. If it does not work, close all programs and wait for another 20 seconds, then
try the green arrow icon again. If it still does not work, you should shut down the player
and disconnect the USB cable.
Q: Why does a mosaic phenomenon appear when playing video files from an external
storage device connected via USB host?
A: The USB host is an USB 2.0 Full-speed interface, higher data rates of your file may
suffer from speed restrictions.
Q: Can the device be turned off when connected to the PC?
A: No, it can’t.
18
Page 19
Q: During power on, why does the TV show a short flash, blue screen or screensaver?
A: This is normal. When the system initializes, it will setup the corresponding
parameters so it can output the correct video signal to the TV, during the initializing
time, the TV will receive incorrect signals or the signals will not be stable and will cause
the TV screen to flash, some TV will treat it as no signal and will display a blue screen
or screensaver.
Q: Why is there no sound playback in movie or music playback when using the YPbPr
output?
A: YPbPr output is a video only output and does not include sound signals. When using
the YPbPr output, please additionally plug the AV OUT or the S/PDIF jack to output
sound signals.
Others
Product improvement, design and specification might be subject to change without prior
notice. Illustrations in this manual may vary from the real product.
LC-Power, 41352 Korschenbroich, support@lc-power.com, www.lc-power.com
19
Loading...