L-com HG2411DP, RE11DP User Manual

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with

the equipment you are installing.

IMPORTANT: Look over the site before beginning any installation, and anticipate possible hazards, especially these: CONTACTING POWER LINES CAN BE LETHAL. Make sure no power

lines are anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables may lean or fall and contact these lines. People

equipment

may be injured or killed if they are touching or holding any pa when it contacts electric lines. Make sure there is NO possibility that equipment or personnel can come in contact directly or indirectly with power lines.

Assume all overhead lines are power lines. The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total

length of the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.

• Select equipment locations that will allow safe, simple equipment installation. work alone. A friend or co-worker can save your life if an accident happens.

• Don’t

• Use approved non-conducting ladders and other safety equipment. Make sure all equipment is in good repair.

• If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.

• If anything such as a wire or mast does come in contact with a power line,

MOVE IT

• Don’t attempt to erect antennas or towers on windy days.

. Instead, save your life by calling the power company.

rt of

DON’T TOUCH IT OR ATTEMPT TO

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS.

human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna.

• The base of the antenna mast or tower must be connected directly to the building protective ground or to one or

more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.

• Refer to the National Electrical Code for grounding details.

• Lightning arrestors for antenna feed coaxial cables are available from HyperLink Technologies, Inc.

This will help prevent fire damage or

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

• DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

• Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical

power.

• Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that

emergency medical aid has been requested.

IP-00015 Rev. B – 05/05 Page 2/2

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

WWW.L-COM.COM E-MAIL: SALES@L-COM.COM PHONE: 1-800-343-1455 FAX: 1-978-689-9484

MOUNTING INSTRUCTIONS

Models: HG2411DP, RE11DP

Hyperlink's patch antennas offer several unique mounting options. They can be mounted flat against a wall, or to a mast using a pair of 2 inch Ubolts. They also accept most tilt-and-swivel security camera brackets equipped with standard 1/4-20 threads (See below for optional mounting Kits).

The HG2411DP/RE11DP is designed with 2 totally separate cross-polarized antennas inside, each with its own lead:

Horizontal Polarization (Left Antenna Lead) Vertical Polarization (Right Antenna Lead)

OPTIONAL MOUNTING KITS

(Sold Separately)

HGX-PMT07 – Stationary

Mounting Kit for mast

mounting

HGX-PMT02 - Small Metal

Tilt-and-Swivel Wall

Mounting

IP-00015 Rev. B – 05/05 Page 1/2

Bracket

HGX-PMT06 – 60 Degree

Tilt-and-Swivel Mounting

Kit for mast mounting.

HGX-PMT03 - Medium Plastic

Tilt-and-Swivel Wall/Desktop

Mounting Bracket

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

WWW.L-COM.COM E-MAIL: SALES@L-COM.COM PHONE: 1-800-343-1455 FAX: 1-978-689-9484

HGX-

Tilt-and-Swivel Mounting

Bracket for Wall or Mast

HGX-PMT08 – Window

PMT04 - Large Metal

mounting

Mounting Kit