L Com LCUSBX, LCUSB User Manual

HAKIT-RTG Series Certified Amplifier Kit

User Manual

Models FCC ID

HAKIT-RTGU-250

HAKIT-RTGIU-250

HAKIT-RTGU-500

HAKIT-RTGIU-500

HAKIT-RTGXU-1000

HAKIT-RTGXIU-1000

(For 802.11b/g Wireless Networks)

MYF-LCUSB

MYF-LCUSBX

Revision: A / Date: 03/10

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

FCC Information

FCC Information

This equipment complies with CFR 47, Part 15.19 of the FCC rules. Operation of the equipment is
subject to the following conditions: (1) this dev ice may not cause harmful interference, and (2) this
device must accept any interference received; including interference that may cause undesired
operation.

This device must not be co-located or operating in conjunction with any other antenna or
transmitter

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Federal Communications Commission (FCC) Requirements, Part 15

This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

---Consult the dealer or an experienced radio/TV technician for help.

Regulatory information / Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions included
in the user documentation provided with the product. Any changes or modifications (including the antennas)
made to this device that are not expressly approved by the manufacturer may void the user’s authority to
operate the equipment. The manufacturer is not responsible for any radio or television interference caused by
unauthorized modification of this device, or the substitution of the connecting cables and equipment other
than manufacturer specified. It is the responsibility of the user to correct any interference caused by such
unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or
distributors will assume no liability for any damage or violation of government

CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. Use only the
supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter
and may violate FCC regulations.

MPE Statement (Safety Information)

Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency
(RF) signal.

Safety Information

In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. Use only
with supplied antenna. Unauthorized antenna, modification, or attachments could damage the
transmitter and may violate FCC regulations.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

When locating the antenna or operating this device you must observe the following exposure limits:

When this device is installed either as a fixed-mount or mobile application there is a
minimum required separation distance of 20 cm from users.

Non-Amplified Systems:

For non-amplified systems simply attach the antenna into the antenna port on the USB adapter and
proceed to USB Adapter Installation section.

Indoor Amplified Systems:

Amplifier connections are clearly labeled on the amplifier unit as shown below.

1. Connect the Antenna to the Amplifier output labeled “ANTENNA”

2. Connect the Radio to the Amplifier input labeled “RADIO” using a pigtail cable.

3. Plug the AC Adapter into the Amplifier’s DC power jack and wall outlet.

Proceed to USB Adapter/Software Installation section.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

Outdoor Amplified Systems:

Amplifier connections are clearly labeled on the amplifier unit as shown below.

1. Connect the Antenna to the Amplifier output labeled “ANTENNA”

2. Connect the DC Injector output labeled “TO AMPLIFIER” to the Amplifier input labeled
“RADIO”

3. Connect the Radio to the DC Injector input labeled “RADIO” using a pigtail cable.

4. Plug the AC Adapter into the DC Injector’s DC power jack and wall outlet.

Proceed to USB Adapter/Software Installation section.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

USB Wireless Adapter and Software Overview

Product Introduction

The WLAN-LCUSB-02 adapter is designed to provide a high-speed and unrivaled wireless performance for your
PC. With a faster wireless connection, you can get a better Internet service, such as downloading, gaming, video
streaming and so on.

The WLAN-LCUSB-02 supports IEEE 802.11b/g 2.4GHz radio operation. With auto-sensing capability, the
adapter packet transfer rate is up to 54 Mbps. Additionally, the WLAN-LCUSB-02 has good capability in anti­jamming and supports WEP, TKIP, AES, WPA, and WPA2 encryption, which prevents outside intrusion, protecting
your personal information from being exposed. Featuring high-performance transmission rate, simple installation
and adaptability, as well as strong security, the WLAN-LCUSB-02 is the perfect solution for small office and home
needs.

System Requirements

Recommended system requirements are as follows:

Windows XP, Windows 2000, Windows Vista and Windows 7
Standard USB 2.0 port
32MB system memory or larger
300MHz processor or higher

USB Driver and Wireless Utility Information

To ensure proper operation of the WLAN-LCUSB-02 wireless adapter, the drivers and utility software
contained on the enclosed CD must be installed. This software is designed specifically for the WLAN­LCUSB-02.

Operational Note:

The WLAN-LCUSB-02 is factory set to operate on channel 6 only.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

Installation

This chapter describes how to install the driver and utility of the WLAN-LCUSB-02. The following procedure is
illustrated in Windows XP.

Installation Guide

Step 1 Find the setup file named WLAN-LCUSB-02 .exe on the included CD and then double-click on it to

start the installation. The page shown in the following figure appears. Then click “Next” to continue.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

Be sure “Driver Files” are checked and click “Next” to continue.

Step 2 Select a destination folder for installation files. Then click “Next” to continue.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

Step 3 Click “Next” to continue.

Step 4 Click “Next” to continue.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

Step 5 The following warning will appear. Click the “Continue Anyway” button to continue the installation.

Step 6 After the installation has been completed, click “Finish” to exit the setup wizard.

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845