l-com HyperGain HG2424G, HyperGain HG2424EG Installation Instruction

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with

the equipment you are installing.

IMPORTANT: Look over the site before beginning any installation, and anticipate possible hazards, especially these:
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power

lines are anywhere where possible contact can be made. Antennas, masts,
towers, guy wires or cables may lean or fall and contact these lines. People
may be inj

ured or killed
when it contacts electric lines. Make sure there is NO possibility that equipment
or personnel can come in contact directly or indirectly with power lines.

Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total

length of the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during
installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.

if they are touching or holding any part of equipment

• Select equipment locations that will allow safe, simple equipment installation.

• Don’t work alone. A friend or co-worker can save your life if an accident happens.

• Use approved non-conducting ladders and other safety equipment. Make sure all equipment is in good repair.

• If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.

• If anything such as a wire or mast does come in contact with a power line,

MOVE IT

. Instead, save your life by calling the power company.

DON’T TOUCH IT OR ATTEMPT TO

• Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES
CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS.

human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna.

• The base of the antenna mast or tower must be connected directly to the building protective ground or to one or

more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.

• Refer to the National Electrical Code for grounding details.

available from HyperLink Technologies, Inc.

• Lightning arrestors for antenna feed coaxial cabl

es are

This will help prevent fire damage or

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

• DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

• Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical

power.

• Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that

emergency medical aid has been requested.

IP-00002 Rev. C – 04/05 Page 3/3

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

HyperGain™ HG2424G

2.4 GHz dBi Reflector Grid Antenna

Installation Instructions

Antenna Components Included:

(1) Antenna Feedhorn Assembly
(1) Feed Reflector
(1) Small Self-tapping Screw
(2) Grid Section Halves
(2) #M6 Stainless Steel U-Bolts w/nuts, flat and lock washers
(2) Mast Clamps
(1) Aluminum “L” Bracket
(4) #M5 x 15mm Machine Screws w/nuts, flat and lock washers
(4) #M6 x 30mm Machine Screws w/nuts, flat and lock washers

Antenna Assembly Instructions:

Lock Washer & Nut

Reflector Grid

#M5 Machine Screw

Assemble the halves of the Reflector Grid using
(4) #M5 machine screws with lock washers, flat
washers and nuts as shown.

IP-00002 Rev. C – 04/05 Page 1/3

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

WWW.L-COM.COM E-MAIL: [e-mail] PHONE: [phone] FAX: [phone]

© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com logo are registered marks.

Feed Reflector

Feedhorn

Small Self-Tapping Screw

Install the Feed Reflector to the front of the
Feedhorn using the small self-tapping screw.

Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.