LCI 426514, 643589 Owner's Manual

™

Smart Jack

OWNER'S MANUAL

Table of Contents

Introduction 2
Safety Requirements 2
Preparation 2
Powered Operation 3

Setting Hitch Height Memory 3
Normal Operation 3
Return to Hitch Height Operation 3
Auto Retract Operation 3

Manual Operation 4

Unhitching From Tow Vehicle 4
Hitching to Tow Vehicle 4

Smart Jack OEM Kit 5
Smart Jack Aftermarket Kit 6
Smart Jack Components 7

Introduction

The Aftermarket Smart Jack™ features a high-efficiency motor, a new streamlined plastic shroud, and a new
user interface. These features, along with the single power lead and the hitch height memory, give the end
user a perfect reason to replace the traditional tongue jack with a far superior product.

Safety Requirements

Warning, Caution and Danger symbols indicate that an installation procedure has a safety risk involved and
may cause death, serious injury or property damage if not performed safely and within the parameters set
forth in this manual. Always wear eye protection when performing this installation procedure. Other safety
equipment to consider would be hearing protection, gloves, and possibly a full face shield, depending on
the nature of the installation procedure.

Failure to act in accordance with the following may result in death, serious injury or property

damage.

Moving parts can pinch, crush or cut. Keep clear at all times.

Lifting the unit off of the ground so that the unit's wheels are not touching the ground will create an

unstable and unsafe condition. Severe property damage, serious injury or death could occur. Keep

people and pets clear of the unit and work area while operating the leveling system.

Preparation

Be sure to park the unit on solid, level ground. Clear all jack landing locations of debris and obstructions.
Locations should also be free of depressions. When parking the unit on extremely soft surfaces, utilize load
distribution pads under each jack. Make sure tires are chocked.

Rev: 07.09.18 Page 2 CCD-0001564

Powered Operation

The hitch height MUST be set in the memory prior to normal operation of the Smart Jack™. If the hitch
height is not set in the memory, the Smart Jack™ and trailer will not function as intended.

NOTE: The battery indicator light (Fig. 1C) flashes or oscillates to validate certain functions of the Smart

Jack™. The light also displays the remaining battery charge of the trailer.

Setting Hitch Height Memory

1. Press and hold the up arrow (Fig. 1A) and down arrow (Fig. 1B) at the same time for a minimum of five
seconds to store the vertical position of the Smart Jack™.

2. The battery indicator lights (Fig. 1C) will flash five times to show that the new position has been
successfully stored in memory.

Fig. 1

B

A

C

Normal Operation

1. Press and hold the up arrow (Fig. 1A) to extend the Smart Jack™.

2. Press and hold the down arrow (Fig. 1B) to retract the Smart Jack™.

Return to Hitch Height Operation

1. Press and release the up arrow (Fig. 1A) and the down arrow (Fig. 1B) at the same time 3 times, holding
on the 3rd time for several seconds until the jack engages and the indicator light oscillates back and
forth.

2. The Smart Jack™ will automatically extend or retract to the original hitch height position stored in the
memory.

NOTE: Visual indication that the jack is actuating to the hitch height is seen through the oscillation of the

battery indicator lights (Fig. 1C) (e.g., lights will illuminate left to right, and then right to left). Battery
indicator light oscillation will continue until the original hitch height is achieved.

3. To cancel an action, press either the up arrow or down arrow. The action in progress will stop.

Auto Retract Operation

NOTE: This function should only be operated once the tow vehicle has been reconnected and secured to

the trailer prior to travel.

1. Press and release the down arrow three times (Fig. 1B), holding on the 3rd time until the jack engages
and the battery indicator light oscillates back and forth.

Rev: 07.09.18 Page 3 CCD-0001564