LCG LCG-WF-5C User Manual

LCG-WF-5C

5 in 1 battery power & wireless DMX

par

USER MANUAL

Please read over this manual before operating the light

www.lc-group.ca

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT
PAR

www.lc-group.ca

5CH Mode

CH

VALUE FUNCTION
0

No Function

CH1

1-255

Red Dimmer

0

No Function

CH2

1-255

Green Dimmer

0

No Function

CH3

1-255

Blue Dimmer

0

No Function

CH4

1-255 Amber Dimmer
0

No Function

CH5

1-255 White Dimmer

9CH Mode

CH VALUE FUNCTION

0 No Function

CH1

1-255 Red Dimmer
0 No Function

CH2

1-255 Green Dimmer
0 No Function

CH3

1-255 Blue Dimmer
0 No Function

CH4

1-255

Amber Dimmer

0

No Function

CH5

1-255

White Dimmer

0 No Function

CH6

1-255 RGBAW Dimmer
0 No Function

CH7

1-255 Strobe, Slow to Fast
0 No Function

CH8

1-255 Auto, Slow to Fast

CH9

0 No Function

1-255 Auto Run

4

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT
PAR

www.lc-group.ca

LED Operation Menu:
Touch Buttons

There are four touch buttons under the LED Alpha-numerical display:
Menu, Down, Up, Enter. Normally, the LED will display the current DMX
address code of the fixture. At this time, presses Menu to choose the
function you want to set up. Press and hold Up or Down to fast scrolling
within the menu options. When an options flashing the LED display,
press Enter to confirm and Menu to exit.

Menu down up Enter

After initialization, the unit is ready for setting and working. Please see
the following table for setting information

5

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT
PAR

www.lc-group.ca

Most important: FIRST CHARGE THE FIXTURES FOR 6-8 Hours on the First
Charge before use. Plug in Power cord. Turn off Power Switch and Turn off
other switch to charge.

Introduction

Unpacking: Thank you for purchasing this product, all products has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the shipping carton for damage
that may have occurred during shipping. If the carton appears to be damaged, carefully inspect
your fixture for any damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, plea se contact the
manufacturer or your dealer for further instructions. Do not return this unit to your dealer without
first contacting.

Introduction: The LCG-WF-5C is a DMX intelligent and battery powered LED par light. This par
light is light weight and compact which makes it a great piece for mobile DJ s and clubs.

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain

or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself; doing so will void your manufactures warranty. In the unlikely event your unit may
require service please contact the manufacturer or your dealer.

PLEASE recycle the shipping carton whenever possible.
General Instructions

To optimize the performance of this product, please read these operating instructions carefully
to familiarize you with the basic operations of this unit. These instructions contain important
safety information regarding the use and maintenance of this unit. Please keep this manual with
the unit, for future reference.

RoHS

1

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT

PAR

www.lc-group.ca

Features

● Power supply: AC110V-250V

● Frequency: 50-60Hz

● Power consumption: 135W

● Light source: 9pcs 15W high brightness 5 in 1 leds

● Lamp life: 6-10 ten thousand hrs

● LED angle: 30(±5) degree

● Color: 16.7 million kinds of color change

● Control channels: 5/ 9 ch s

● Control mode: DMX512, master/slave, auto, sound active (can order wireless DMX512 also)

● Automatic model(by function button) : color change, color strobe, color dimmer, color

gradual change/color jump change

● Operation menu: 4 digit digital LED display

● Packing size: 240 *130*250mm

● N.W: 3kg

● G.W: 3.5kg

Safety Precautions

● To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

● Do not spill water or othe r liquids into or on to your unit.

● Be sure that the local power outlet match that of the required voltage for your unit.

● Do not attempt to operat e this unit if the power cord has been frayed or broken. Do not

attempt to remove or break off the ground prong from the electrical cord. This prong is used to
reduce the risk of electrical shock and fire in case of an internal short.

● Disconnect from main power before making any type of connection.

● Do not remove the cover under any conditions. There are no user serviceable parts inside.

● Never operate this unit when it s cover is removed.

● Never plug this unit in to a dimmer pack.

● Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device an d a wall.

● Do not attempt to operate this unit, if it becomes damaged.

● This unit is intended for indoor use only; use of this product outdoors voids all warranties.

● During long periods of non-use, disconnect the unit s main power.

● Always mount this unit in safe and stable matter.

● Power-supply cords should be routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular attention to the point they exit from unit.

● Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See
“Cleaning” for details.

● Heat -The appliance should be s ituated away from heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.

● The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in
performance 2

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT

PAR

www.lc-group.ca

There are two buttons on the rear panel of the lighting. One is for power, and the other is for
signal.

● When use the fixture with DMX, not wireless, please switch the signal button for “off”

● When use the wirele s s DMX, plea se sw itch the bu tt o n for “on”

● When charge the light, please switch both of the button for “of”. At the same time, if the

switch for power is “on”, the light will be at work during the process of charge, but will consume
some power from the charge; if the switch for power is “off”, the light will be blackout and not be
at work.

Tip for the battery and charge:

● The battery can last for 4-5 hours when all LEDs on after full charge , and can last for more

than 6-8 hours on auto running mode. Up to 20 Hours with one color diode on. Results will vary
based on brightness of LEDs

● It is suggested to charge the battery for at least 4 hours, which will extend the life span of
the battery.

7

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT

PAR

www.lc-group.ca

For Battery Function and Charge
The unit has the function of battery powered. The button for battery and

charge is set on the rear panel. It is showed as the following picture,
and the function is described as below.

1. Alpha-numeric display 2. Touch switches 3. DMX-Out socket

4. DMX-In socket 5. Power out 6. Microphone 7. Power in

1. Antenna 2. Power switch for wireless dmx 3. Power switch for
battery power 4. Wireless dmx code 5. Wireless dmx code indicate

（same color as transmitter） 6.Battery power indicator

6

LCG-WF-5C 5 IN 1 BATTERY & WIRELESS FLAT

PAR

www.lc-group.ca

● Fuse standard is 2A/250V

● Grounded using yellow/green line

● The ambient temperature must a lways be under +35° C

Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches

the required voltage for your lig ht is workable in 100-220V/50~60Hz. Because line voltage may
vary from venue to venue, you should be sure your unit voltage matches the wall outlet voltag e
before attempting to operate you fixture.

Operating Instructions
Operating Modes: You can use the LCG-WF-5C in 5 ways:

● Sound activation – The unit will activated by the sound signal.

● Static display – The unit will display the color in static way.

● Auto Mode -The un it will automatically chase through the different patterns.

● DMX control mode -This function will allow you to control the lighting with a standard DMX

512 controller.

● Battery powered – This function will allow you to control the lighting independently without
any DMX cable

DMX Mode: Operating through a DMX controller give the user the freedom to create their own
programs tailored to their own individual needs. This function also allows you to use your
fixtures as pattern changing lights.

1. This function will allow you to control each individual fixtures traits with a standard DMX 512
controller.

2. The LCG-WF-5C use 5/9 DMX channels to operate. Please see “DMX channel and

Functions” for the DMX traits.

3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard

DMX controller. Set your desired DMX address following the setup specifications that come with
your DMX controller.

4. The unit can automatically recognize the DMX signal once the DMX connection is done.

DMX Linking:

To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When
a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.

3