LCG LCG-2501WB User Manual

Download

www.lc-group.ca

USER MANUAL

LEAD PACK 1

LCG-2501WB

(1x25W-RGBAW-BAT-WI 5-in-1)

www.lc-group.ca

Catalogue

1. Summary ................................................................................................................ 3

2. Safety Instruction ................................................................................................... 4

3. Outside Size Picture ............................................................................................... 5

4. Main Function ........................................................................................................ 7

5. DMX Control Function ............................................................................................ 8

6. Display Operation instruction .............................................................................. 10

7. Instruction for compatible Sweden DMX wireless module ................................... 16

8. Infrared keyboard operation ................................................................................ 16

9. AOperating Control Instruction ............................................................................ 18

10. XLR cable connecting ........................................................................................... 18

11. Trouble Shooting .................................................................................................. 19

Please read over this manual before operating the light

LEAD PACK 1(LCG-2501WB)-User Manual

1. Summary

 Summary



Thank you for purchasing our LEAD PACK 1. Please read th ese instructions caref ully before begin

and

operate the fixt ur es a cc ord in g to t hes e ins tr uc tio ns to avo id a ny poss ib le d am a ge s and

accidents cause s

by misusage

 P

roduct introduction

LED LEAD PACK 1 light uses castin g aluminum housing

, designed in a f ashion of hydro dynamic

form.

Appearance shows. It adopts high power

5-in-1

LED, which refers to single LED is made of

R,G,B,A,W 5-IN-1 LED, And long life span, low consumption, good

color mixing effect and high brightness are the most prominent features. Each kind of LED can be independently dimmed. The built-in program includes dimming, strobe, eotic, gradual change, fading and so on.

It uses power switch, performs

low weight and consumption, stable

capability and long life. International standard DMX 512 signal is

requested.

 P

acking List

 LEAD PACK 1 1 PC  DMX Signal Cable 1 Set  Power cable 1 PC  User Manual  Warranty Card  IP Remote Control

LEAD PACK 1(LCG-2501WB)-User Manual

2. Safety Instruction

 Safety Notes

! Enquire the skilled people before any repair; ! A lways make sure disconnect from the power source before setting up, serving and moving;. ! Avoid direct eye exposure to the fixture when it is on;

 Safety instruction

● Make sure the power supply voltage are co nsistent with thi s lig h ts，Ensure the use of voltage is in the range o

f the request technical parameter.

●Before the installation, please check the light’s fasteners and mechanical structure have been received i

od condition and appear no damage

●

This light is designed for indoor use;

working

temperature is low er than 40 de gre e.

●T

he fixtures maybe mounted in any position provided there is adequate room for ventilation. Make sure

there are no inflammable and explosive items (ornaments) in 0.5 meters away.

●Yellow / green cabling earthling safety; no flicker when the fixture is working o

LEAD PACK 1(LCG-2501WB)-User Manual

3. Outside Size Picture

Figure 1: LEAD PACK 1 Picture

Figure 2: The Rear Connections

1*25W 5-in-1 RGBAW COB LEDs

Button Control Panel

w/Micro OLED Display

Charge Status LED

Locking Adjustment Knob

Antenna

IR Remote Sensor

RF-ID LED

Cast Aluminum Housing w/Natural Convection Cooling

Power Button

Mounting Brackets

Locking Adjustment Knob

AC Power In

Locking Adjustment Knob

LEAD PACK 1(LCG-2501WB)-User Manual

Figure 3: The Outside Size Picture

240.00

163.00

121.94

184.94

183.00

108.00

184.94

LEAD PACK 1(LCG-2501WB)-User Manual

4. Main Function

 Input voltage: AC 100V-264V/47-63HZ  Power consumption：28W

 Lamp Type：25W LED 5-in-1 R、G、B、A、W(1PCS) COB LED

 Life span: 50000~100000hours

 PWM Dimmer：1500HZ(16666 grades)

 Control Signal：DMX512

 Infrared keyboard control

 2.4G wireless DMX receiver: WI-DMX & Sweden

 Channel：11CH/8CH/6CH/5CH

 Function Effect: dimmer, strobe, gradual change

 T ouch buttons, automatic lock key

 Battery charge time:5 hours

 Full power battery duration:2.5 hours

 Cooling mode: Natural Convection

 Anti-electricity intension：1.5KV

 Insulation Resistance:>2MΩ

 Beam Angle: 25°(15°,45° or 60° Optional)

 Weigh2.44Kg

LEAD PACK 1(LCG-2501WB)-User Manual

5. DMX Control Function

 DMX Channels

5CH 6CH 8CH 11CH Value Function

- CH1 CH1 CH1 0-255 Dim all

CH1

CH2

0-255

CH2 CH3 CH3 CH3 0-255 G CH3 CH4 CH4 CH4 0-255 B CH4 CH5 CH5 CH5 0-255 A CH5 CH6 CH6 CH6 0-255 W

- - CH7 CH7

0-5 No strobe

6-115 Normal strobe(slow to fast) 116-130 No strobe 131-170 Electronic Sine wave(slow to fast) 171-210 Opening pulse(slow to fast) 211-250 Closing pulse(slow to fast) 251-255 No strobe

- - -

CH8(CH8

Prior to

CH10)

0-5

No effect

6-10

CT01(Call custom color in menu settint)

11-15

CT02

16-20 CT03

21-25 CT04

26-30 CT05

31-35 CT06

36-40 CT07

41-45 CT08

46-50 CT09

51-55

CT10

56-60

AUTO 1(R,G,B,RG,RB,GB)

61-65

AUTO 2(R↑,R↓,G↑,G↓,B↑,B↓,A↑,A↓,W↑,W↓)

66-70

AUTO 3(R↑G↑,R↓G↓,R↑B↑,R↓B↓,B↑G↑,B↓G↓)

71-75

AUTO 4(R↑G↑B↑W↑,R↓G↓B↓W↓)

76-80

AUTO 5(Rainbow effect: B,BG↑,BG,B↓G,G,GR↑,GR,G↓

R,R,RB↑,RB,R↓B)

81-220 Reserved 221-225 CHASE1 226-230 CHASE2 231-235 CHASE3 236-255 Reserved

- - - CH9 0-255 Auto speed, fast->slow

- - -

CH10

Virtual color wheel

LEAD PACK 1(LCG-2501WB)-User Manual

0-10

No effect

11 Blue (Blue=full, Red+Green+White=0)(step)

12-50

Red=0, Green->up, Blue =full, White=0(proportional)

Light Blue (Red=0, Green=full, Blue =full, White=0)(step)

52-90 Red=0, Green=ful l, Blu e->down, White=0(proportional)

91 Green (Red=0, Green=ful l, Blue =0, White=0)( step)

92-130 Red->up, Green=full, Blue=0, White=0(proportional)

131 Yellow (Red=full, Green=full, Blue=0, White=0)(step)

132-170 Red=full, Green->down, Blue=0, White=0(proportional)

171 Red(Red=full, Green=0, Blue=0, White=0)(step)

172-210 Red=full, Green=0, Blue->up, White=0(proportional)

211 Magenta (Red=full, Green=0, Blue=full, White=0)(step)

212-250

Red -> down, Green=0, Blue=full, White=0(proportional)

251-255

Blue (Red=0, Green=0, Blue=full, White=0)(step)

- - CH8 CH11

0-10 Use the dimmer mode which menu had set up 11-20 Linear curve 21-30 Square law curve 31-40 Inverse square law curve 41-50 S-curve 51-60 Linear curve and smooth

61-70

Square law curve and smooth

71-80 Inverse square law curve and smooth

81-90

S-curve and smooth

91-255

Use the dimmer mode which menu had set up

LEAD PACK 1(LCG-2501WB)-User Manual

6. Display Operation instruction

 MENU : access the menu or return to a previous menu option  ENTER: select the current menu option  UP: menu selection or parameter increments  DOWN: menu selection or parameters decrease

Menu Tree

TAB

LEVEL1

LEVEL2

LEVEL3

LEVEL4

ADDR(Address)

001-512 STAT(Static control)

0-255 *

G 0-255 *

B 0-255 *

A 0-255 *

W 0-255 *

SHUT 0-255 * SET(Set) WIRE(Wireless set) REST(reset) YES/NO

KEY BAT(battery output) HIGH/MIDDLE/LOW CAL(Calibration) R 0-255

G 0-255

B 0-255

A 0-255

W 0-255

USE YES/NO

CHMD(Channel mode)

11CH

8CH

6CH

LEAD PACK 1(LCG-2501WB)-User Manual

5CH

DIM(Dimming mode)

LIN(linear)/SQR(square

law)/ISQR(inverse square

law)/SCUR(S-curve)/LIN.(li

near smooth)/SQR.

(square law smooth)/ISQR.(inverse square law smooth)/SCUR.(S-curve smooth)

LOCK YES/NO CTST(Custom color set)

CT01 R 0-

255

. G 0-255

. B 0-255

. A 0-255

. W 0-255

CT10 AUTO(Auto) AT01 RUN.. *

. RUN.. *

AT05 RUN.. *

ATSP(Auto speed) 0-255(S)

CHS1（Chase 1）

RUN.. *

CHS2（Chase 2）

RUN.. *

CHS3（Chase 3） RUN.. * PROG（Program） CHS1（Chase 1） SC01（Scene 1） R 0-255

. . G 0-255

. . B 0-255

. . A 0-255

. . W 0-255

. . SHUT 0-255

. . AUTO

NONE,AT0

1-AT05 . . ATSP 0-255(S) . . TIME 0-255(S) . . WAIT 0-25.5(S) . . USE YES/NO . SC25（Scene 25 ） CHS3（Chase 3）

INFO（Information

SOFT(Software version)

Vx.x

BATTERY 0%-100%

LEAD PACK 1(LCG-2501WB)-User Manual

POW(Power reduction) xxx% LOAD(Load) ST L（Setting load) YES/NO PR L（Program load) YES/NO

Instructions：

When enter to the “*” position displayed on the LED. When power cycle it will jump to the “*” position and running again. And in these position it will not return back to the default display after two minutes.

6.1 DMX ADDRESS SETTING

1) Press the 【ENTER】 button in 【ADDR】 menu, then enter to the DMX address setting.

2) Press the【UP/DOWN】button to select【1-512】numerical value.

3) Press the【ENTER】button to escape and save.

6.2 STATIC SETTING

1) Press the【ENTER】button in 【STAT】menu, then enter to the static setting.

2) Press the【UP/DOWN】 button to select 【RED】，【GREEN】，【BLUE】，【AMBER】,【WHITE】 and【SHUT】.

3) Press the【UP/DOWN】button to set up the【0-255】numerical value.

4) Press the【ENTER】button to escape and save.

6.3 Wireless set

1) Press the【ENTER】button in【WIRE】menu, then enter to the wireless set.

2)【RESET】Simulating the power outage of wireless module and then press the button to power on

3)【KEY】Similar to an external button

6.4 Battery output setting

1) Press the【ENTER】button in【BAT】menu, then enter to the Battery output setting.

2) Press the【UP/DOWN】button to select【HIGH】,【MIDDLE】, 【LOW】

3) Press the【ENTER】button to escape and save.

6.5 COLOR CAST CALIBRATION SETTING

1) Press the【ENTER】button in 【CAL】menu, then enter to the color cast calibration setting.

2) Press the【UP/DOWN】button to select 【RED】，【GREEN】...【WHITE】

3) Press the【UP/DOWN】button to set up the【0-255】numerical value.

LEAD PACK 1(LCG-2501WB)-User Manual

4) On the【USE】interface, pressing【YES】button means valid,【NO】means invalid.

) P

ress the【ENTER】button to escape and save. Illustrations: When pressing the【YES】button which means valid on the【USE】interface, the actual output value of RED...WHITE is output in accordance with the percentage which the color cast calibration value divides 255.

6.6 CHANNEL MODE SETTING

1) Press the【ENTER】button in 【CHMD】menu, then enter to the channel mode setti ng. 2

) P

ress the【UP/DOWN】button to select【11CH】，【8CH】，【6CH】，【5CH】 3

) P

ress the【ENTER】button to escape and save.

6.7 DIMMING MODE SETTING

1) Press the【ENTER】button in【DIM】menu, then enter to the dimming mode setting.

2)Press the【UP/DOWN】button to select【LIN】，【SQR】，【ISQR】，【SCUR】，【LIN.】，【SQR. 】，【ISQR.】and【SCUR.】. 3

) P

ress the【ENTER】button to escape and save. Illustrations：When setting【LIN.】，【SQR.】，【ISQR.】and 【SCUR.】 in 【DIM】 menu, there will be added a little delay dimming effect for smooth.. Dimming curve:

Linear curve: square law curve: Inverse Square law curve: S-curve:

6.8 AUT O LOCK KEY SETTING

1) Press the【ENTER】button in【LOCK】menu, then enter auto lock key setting. 2

) P

ress the【UP/DOWN】button to select【YES】,【NO】 3

) P

ress the【ENTER】button to escape and save.

Instructions: When set to [YES], it will lock automatically after two minutes to prevent accidental triggering flood flushing. When in the order press MENU->UP->DOWN->ENTER three times to unlock

，and the time

LEAD PACK 1(LCG-2501WB)-User Manual

between two keys be press down must within 2 seconds.

6.9 CUST OM COLOR SETTING

1) Press the 【ENTER】 button in 【CTST】 menu, then enter to the custom color setting.

2) Press the 【UP/DOWN】 select 【CT01】…【CT10】

3) Press the 【UP/DOWN】 select 【R】,【G】...【W】

4) Press the【UP/DOWN】button to select【1-255】numerical value.

5) Press the【ENTER】button to escape and save.

6.10 AUTO RUN, SELF-PROGRAM RUN

1)Press the【ENTER】button in【AUTO】menu, then enter to the auto run,self-program run.

2)Press the【UP/DOWN】button to select【AT01】…【AT05】，【 AUTO SPEED】，【 CHASE01】…【SOUND2 】

3)Press the【ENTER】button to start running.

6.11 EDIT SELF-PROGRAM

1) Press the【ENTER】button in【PROG】menu, then enter to the edit self-program.

2) Press the【UP/DOWN】button to select【CHASE01】…【CHASE03】

3) Press the【ENTER】button for confirmation and enter to the next menu.

4) Press the【UP/DOWN】button to select【SCENE01】…【SCENE20】

5) Press the【ENTER】button for confirmation and enter to the next menu.

6) Then press the【UP/DOWN】button to select【RED】…【SHUT】，【TIME】，【WAIT】，【USE】

7) Press the【UP/DOWN】button to set up the parameter which are needed.

8) Press the【ENTER】button t o escape and save. Illustrations：When【USE】 is set to be【NO】， or the parameter of【TIME】 is 0, it will not run this scene.When 【WAIT】is set to be FADE time, the running process isas the following chart showing.

6.12 CHECK THE LIGHTING INFORMATION

LEAD PACK 1(LCG-2501WB)-User Manual

1) Press the【ENTER】button in【INFO】menu, then enter to the checking the lighting information. 2

) 【

SOFT】button is for software version information.

) 【

BAT】is battery level from 0% to 100%。

) 【PO

W】button is for the current information of power reduction..

6.13 LIGHTING SETTING PARAMETER RESET

1) Press the【ENTER】button in【ST L】menu, then enter to the lighting setting parameter reset. 2

) P

ress the【UP/DOWN】button to select【YES】. 3

) P

ress the【ENTER】button to escape and save. Illustrations： “ADDR” “CTST” and “PROG” are not reset, the others reset to the underlined value of the word.

6.14 【PROG】SELF-PROGRAMMING PARAMETER RESET

1) Press the【ENTER】button in【PR L】menu, then enter to the【PROG】self-programming parameter reset. 2

) P

ress the【UP/DOWN】button to select【YES】. 3

) P

ress the【ENTER】button to escape and save.

LEAD PACK 1(LCG-2501WB)-User Manual

7. Instruction for compatible Sweden DMX wireless

module

1. Four mode to choose from, as bellow ;

1) Green mode ; Sweden compatibility such as PR River PR-4500.

2) Blue mode ; Sweden transmit compatible.

3) Yellow mode ; Standard 2.4G compatible.

4) Red mode ; Custom signal compatible such as WI-DMX.

2 . Red and Yellow mode have sub colors to choose from as bellow ,;

1) RED---( Red / Green / Blue / Yellow / pale Blue / Pink )

2) Yellow---( Red / Green / Blue / Yellow / pale Blue / Pink and White )

3. Changing color mode into the menu ,;

1) Go to the SET section then WIRE. Two option into the WIRE section ( Reset and KEY ).

2) note,; Reset every time to change mode however the sub colors are available without

resetting

3) After reset use the Key and scroll with Enter to choose the colors. When selected press and hold Enter one second to confirm.

4. Green is receiving Sweden compatible mode. To reset on this mode simply hold ENTER on KEY menu for 3 seconds. This will delete the previous match when modifying install or transmitter. To synchronize again, press the button on the transmitter for new match. The indicator of the transmitter and fixture will flash at the same time. Control from DMX device gets active when the indicator stops blinking.

5. Blue mode is for transmitting Sweden compatible. As all transmitting function of this wireless module is not used, please ignore this function. Even when it’s set as master it can not use wireless module to transmit DMX signals.

6. egg ,; Standard 2.4G China transmitter styx under RED will be compatible with the Lead Pak in Yellow mode and sub RED. Same if the Standard 2.4 China transmitter sticks are set to Green, set the Lead Pak into Yellow and sub Green. The WI-DMX will synchronize in the RED mode with the RED sub frequency.

LEAD PACK 1(LCG-2501WB)-User Manual

8. Infrared keyboard operation

1) 【

MENU】, 【UP】, 【DOWN】, 【ENTER】is same as the keys on the fixture.

2) 【R1】...【W2】，【SHUT】is shortcut for 【STAT】.

3) 【AT 01】,【CHS01】, 【ATSP 】,【SOU1】is correspond to the positon of 【AT01】,【CHS01】,【SOU1

】 in the MENU.

4) 【CLEAR】is clear the value of 【R1】, 【G1】... 【SHUT】 then save and reset。

LEAD PACK 1(LCG-2501WB)-User Manual

9. Operating Control Instruction

 Master/Slave

When the fixtures work in master mode it will send out the signal for the slave synchronous with it. To avoid the host signal and DMX512 signals interfere with each other, should cut off the DMX512 signals. The signal lines are longer than 60 meters (20 lamps), should increase a signal amplifier.

10. XLR cabl e connecting

 XLR cable：

The standard connection way of the XLR is: one end connects to the male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal

Noted：In order to avoid failures and interference signal transmission，we connect a

resistance120Ω （ 1/4W ） at the end of the DMX connecting as below:

 The Conversion between 3 pin and 5 pin XLR If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

LEAD PACK 1(LCG-2501WB)-User Manual

11. Trouble Shooting

PROBLEM REASON AND ACTION

The lighting can’t be

started normally



Check the power connection is correct or not.

 Please detect the voltage.  Power

supply is damaged or incorrect connected. Call a

qualified personnel to fix it.



Connection of control board is not correct. Call a qualified personnel to fix it.

Out of console’s

control

 

Please check the DMX connector and the power connection

is connected correctly or not. It means ha ving signal if it show s twinkling of the decimal point which in the lower right corner of the screen when exiting the screen saver.

 Please check the DMX address setting of lighting is correct or

not.

 Check【CHMD】setting is correct or not.

 Please check whether the DMX line is near t o the high voltage

wire or not. In that case, it will damage or interf ere the DMX

electric circuit.

The beam appears

dim ,the brightness

declines obviously

 Check whet

her the 【CAL】is started or not and the set value is

too small.

 Check whether the【POW】

is in over temperature protection

situation or not, if yes, please take measures for ventilation.

LCG LCG-2501WB User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual