LCG LCG-072 User Manual

1

LED

LED S

S

S onic

onic

onic W

W

W ave

ave

ave B

B

B ar

ar

ar DMX

DMX

LCG-072

User

User Manual

Manual

Please

Please read

read

read the

the

the instructions

instructions

instructions carefully

carefully

carefully before

before

before use

use

2

1.

1. SAFETY

SAFETY

SAFETY INSTRUCTIONS:

INSTRUCTIONS:

• Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.

• Unpack and check carefully there is no transportation damage before using the fixture.

• Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.

• It’s important to ground the yellow/green conductor to earth in order ot avoid electric shock.

• Disconnect main power before servicing and maintenance.

• Use safety chain when fixes this fixture. Don ’ t handle the fixture by taking

its head only, but always by taking its base.

• Maximum ambient temperature is

TA:

40 ° C. Don ’ t operate it where the

temperature is higher than this.

• The unit is for indoor use only. Use only in a dry location.

• Don ’ t connect the device to any dimmer pack.

• Make sure there are no flammable materials close to the unit while operating,

as it is fire hazard.

• The housing or the lenses must be replaced if they are visibly damaged

• Do not allow children to operate the unit.

• Replace fuse only with the same type.

• Never try to repair the unit by yourself. Repairs carried out by unskilled

people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center.

• Disconnect the mains power if the unit is not used for a long time

• Do not look directly at the Led Light beam while the unit is on

•

To

prevent or reduce the risk of electrical shock or fire, do not expose the

fixture to rain or moisture.

2.

2. INSTALLATION

INSTALLATION

INSTALLATION :

• The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

• The unit must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

3

3.

3. TECHNICALS

TECHNICALS

TECHNICALS SPECIFICATIONS

SPECIFICATIONS

• LEDs: 12 x TRI-3W LEDs

• Beam angle: 30 °

• LED display for easier operation

• Built-in programs, sound active, auto run, M/S mode, DMX mode, static

colors, IR Remote

• Three sound active modes

• Very good equalizer and chasing effects with music

• DMX-512: 3,4,4,36,37,37 channels selectable

• Power consumption: 45W

• Power input: AC 120V/60Hz

• Size: 109 x 12 x 73 cm

• Weight: 4.2kg.

4.

4. OPERATION

OPERATION

a.

a. Built-in

Built-in

Built-in Program

Program

1) Press MODE button, enter the built in program mode menu “

Pr.

××”

2) Press UP or DOWN button, select the effects program Pr.01 ～ Pr .35.

3) Press SETUP button, enter setup program run speed menu “ SP ××”

4) Press UP or DOWN button, setup the speed value SP01 ～ SP100 （ FL ）

5) Press SETUP button, enter setup program run speed flash menu “ FS ××”

6) Press UP or DOWN button ,setup flash value FS00 ～ 99

b.

b. Auto

Auto

Auto Running

Running

1. Press MODE button, enter auto run mode menu“AUTO ”

2. Press SETUP mode, enter setup auto run mode speed menu “ SP ××”

3. Press UP or DOWN button ,setup speed value SP01 ～ SP100 （ FL ）

4. Press SETUP button, enter setup auto run mode flash menu “ FS ××”

5. Press UP or DOWN button ,setup flash value FS00 ～ 99

c.

c. DMX

DMX

DMX Mode

Mode

1. Press MODE Button, enter DMX control run mode menu “ d. ×××”

4

2. Press UP or DOWN button ,setup DMX address value d.001 ～ d.512

3. Press SETUP button, enter setup DMX mode menu xxch

4. Press UP or DOWN button ,setup DMX mode 3ch, 4-c1,4c-2, 36 ch, 37c1, 37c2.

CHANNEL

CHANNEL numbers

numbers

numbers 3,

3,

3, 4,

4,

4, 4,

4,

4, 36,

36,

36, 37,37

37,37

DMX mode 1 ： 3C

CHANNEL VALUE FUNCTION

CH1 0-255 RED CH2 0-255 GREEN CH3 0-255 BLUE

DMX mode 2 ： 4C-1

CHANNEL VALUE FUNCTION

CH1 0-255 RED CH2 0-255 GREEN CH3 0-255 BLUE

CH4 0-255 MASTER DIMMER

DMX mode 3 ： 4C-2

CHANNEL VALUE FUNCTION

CH1 0-255 MASTER DIMMER CH2 0-255 RED CH3 0-255 GREEN

CH4 0-255 BLUE

DMX mode 4 ： 36C

CHANNEL V ALUE FUNCTION SECTION

CH1 0-255 RED

1

CH2 0-255 GREEN

CH3 0-255 BLUE

CH4 0-255 RED

2

CH5 0-255 GREEN

CH6 0-255 BLUE

CH7 0-255 RED

3

CH8 0-255 GREEN

CH9 0-255 BLUE

CH10 0-255 RED

4

CH11 0-255 GREEN

CH12 0-255 BLUE

CH13 0-255 RED

5

CH14 0-255 GREEN

5

CH15 0-255 BLUE

CH16 0-255 RED

6

CH17 0-255 GREEN

CH18 0-255 BLUE

CH19 0-255 RED

7

CH20 0-255 GREEN

CH21 0-255 BLUE

CH22 0-255 RED

8

CH23 0-255 GREEN

CH24 0-255 BLUE

CH25 0-255 RED

9

CH26 0-255 GREEN

CH27 0-255 BLUE

CH28 0-255 RED

10

CH29 0-255 GREEN

CH30 0-255 BLUE

CH31 0-255 RED

11

CH32 0-255 GREEN

CH33 0-255 BLUE

CH34 0-255 RED

12

CH35 0-255 GREEN

CH36 0-255 BLUE

DMX mode 5 ： 37C-1

CHANNEL VALUE FUNCTION SECTION

CH1 0-255 RED

1

CH2 0-255 GREEN CH3 0-255 BLUE

CH4 0-255 RED

2

CH5 0-255 GREEN CH6 0-255 BLUE

CH7 0-255 RED

3

CH8 0-255 GREEN CH9 0-255 BLUE

CH10 0-255 RED

4

CH11 0-255 GREEN CH12 0-255 BLUE

CH13 0-255 RED

5

CH14 0-255 GREEN CH15 0-255 BLUE

CH16 0-255 RED

6

6CH17 0-255 GREEN

CH18 0-255 BLUE

CH19 0-255 RED

7

CH20 0-255 GREEN CH21 0-255 BLUE

CH22 0-255 RED

8

CH23 0-255 GREEN CH24 0-255 BLUE

CH25 0-255 RED

9

CH26 0-255 GREEN CH27 0-255 BLUE

CH28 0-255 RED

10

CH29 0-255 GREEN CH30 0-255 BLUE

CH31 0-255 RED

11

CH32 0-255 GREEN CH33 0-255 BLUE

CH34 0-255 RED

12

CH35 0-255 GREEN CH36 0-255 BLUE

CH37 0-255 MASTER DIMMER

DMX mode 6 ： 37C-2

CHANNEL VALUE FUNCTION SECTION

CH1 0-255 MASTER DIMMER CH1 0-255 RED

1

CH3 0-255 GREEN CH4 0-255 BLUE

CH5 0-255 RED

2

CH6 0-255 GREEN CH7 0-255 BLUE

CH8 0-255 RED

3

CH9 0-255 GREEN CH10 0-255 BLUE

CH11 0-255 RED

4

CH12 0-255 GREEN CH13 0-255 BLUE

CH14 0-255 RED

5

CH15 0-255 GREEN CH16 0-255 BLUE

7

CH17 0-255 RED

6

CH18 0-255 GREEN CH19 0-255 BLUE

CH20 0-255 RED

7

CH21 0-255 GREEN CH22 0-255 BLUE

CH23 0-255 RED

8

CH24 0-255 GREEN CH25 0-255 BLUE

CH26 0-255 RED

9

CH27 0-255 GREEN CH28 0-255 BLUE

CH29 0-255 RED

10

CH30 0-255 GREEN CH31 0-255 BLUE

CH32 0-255 RED

11

CH33 0-255 GREEN CH34 0-255 BLUE

CH35 0-255 RED

12

CH36 0-255 GREEN CH37 0-255 BLUE

d.

d. Sound

Sound

Sound Active

Active

1. Press MODE button, enter sound active mode “ SOUd ”

2. Press SETUP button, to set up sound active mode and sensitivity menu “ S × . ××”

3. Switch over sound active mode S1. ×× ,S2. ×× ,S3. ×× and the running direction.

4. Under the mode of S1. ×× ,S2. ×× ,S3. ×× , press UP or DOWN button ,to set up the sound active sensitivity value S1.00 ～ S1.31,S2.00 ～ S2.31,S3.00 ～ S3.31 or the running direction when on the mode of S1. ×× ,S2. ××

e.

e. Slave

Slave

Slave Mode

Mode

1. Press MODE button, enter slave mode “ SLAV ”

2. The running effect program of master light is the same with all slaves light

f.

Static

Static Color

Color

1. Press MODE button, enter static color mode “ COLR ”

2. P ress SETUP button enter the static color, press UP or DOWN

8

button ,you can select 7 static colors (1.-r ； 2.-rg ； 3.-g ； 4.-gb ； 5.-b

；

6.-rb ； 7.rgb; 8OFF).Press SETUP again, you can press UP or DOWN adjust the brightness of the static colors .Press SETUP button can setup the flash “ FSxx ” of the color .Also press UP or DOWN can adjust the speed of flash of speed.

g.

g. IR

IR

IR Remote

Remote

1. Press the “ mode”, when LED display ： -ir- is on IR remote. IR remote instruction as below:

A

A ） select

select

select the

the

the built-in

built-in

built-in programs

programs

programs by

by

by IR

IR

IR remote

remote

remote :

1) Press down the“AUTO”, enter the built-in program select mode. Press down the “ + ” / “ -”, select the built-in programs Pr .01~Pr.35.

（ Note: the button“AUTO ” function amount to press the button

Pr.xx

） .

2) Press down the “ SPEED”, enter to the state of built-in program running speed, press down the “ + ” / “ -”, adjust the built-in program running speed.

3) Press down the “ STROBE”, enter to strobe state, press down the “ + ” / “ -”, adjust

the speed rate of built-in programs, and then press the “ STROBE”, the stroboscopic stop.

4) Press down the “ FADE”, the light color will from one change to another one,

press down the “ FADE ” again, the light color will from one hopping to another one.

B

B ） select

select

select the

the

the sound

sound

sound active

active

active mode

mode

mode by

by

by IR

IR

IR remote

remote

remote :

1) Press the “ SOUND ” or “ SENSITIVITY”, enter sound active mode, press down

the “ + ” / “ -”, adjust the sensitivity of sound active.

2)select the static color mode by IR remote ：

Press the “ MANUAL”, enter to select the static color,

Press the numeric buttons “ 0 ” ~ “ 9 ” ， select the fixed monochrome:

0 1 2 3 4 5 6 7 8 9

Whit

e

Red Orang

e

Yello

w

Gree

n

Cyan Blue PurplePink Ambe

r

3)press down the “ MANUAL”, enter select the static color mode, press down the “ R ” （ “ G ” or “ B ” ） enter to dimming color mode ，

Press the “ 0 ” - “ 9 ” in turn ， the first input is higher ， the effectively composed

number between 0-100, press the “ % ” again, confirm this number is the percentage of dimming monochrome.

For example, press the “ MANUAL ” + “ R ” + “ 5 ” + “ 0 ” + “ % ” in turn, set the red LED

brightness is 50% of all the bright. When adjust one monochrome, press a effectively number , the correspond color will fading up once, if the setting is ok, the light board will lighting the monochrome which you setting. If the setting is wrong, the light board will display the color before you set, can reset the color .

4) press down the “ R ” or “ G ” or “ B ” ， display the user-defined color, press down

9

the “ + ” / “ -”, adjust the correspond monochrome brightness .

C

C ） Black

Black

Black out

out

out and

and

and restore

restore

restore factory

factory

factory settings

settings

settings by

by

by IR

IR

IR remote.

remote.

1) press down the “ BLACK OUT”, enter black out state; press the “ BLACK OUT ” once more, recovery the state before

2) In black out state, press down the “ 9 ” + “ 8 ” + “ 7 ” in turn, restore factory setting.

P.S

: A. If no press the four buttons in 20 seconds, LED display will turn off , now if press any button, the LED display will recover the state before turn

off,

then each button

will restore their function.

B. when the system power on, will first display the system version number V1.0, continue about 2 seconds ， then will operation the user setting working mode. C. IR remote offer fast operation, more subtle operations please press the button to satisfy your needs.

5.

5. DMX512

DMX512

DMX512 CONNECTIONS:

CONNECTIONS:

The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.

DMX 512 120 OHM 1/4W

10

• 1

•

3

• 2

1. 1

2.

3

3. 2

INPUT

OUTPUT

COMMON

DMX +

DMX -

Termination reduces signal errors and to avoid signal transmission problems and interference. It is always advisable to connect a DMX terminal. (resistance 120ohm 1/4W ) between pin2 (DNX-) and pin3 (DMX+) of the last fixture.

1. Connect the fixture together in a“daisy chain ” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a 2Y ” cable. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system.

2. The DMX output and input connectors are pass-through to maintain the DMX circuit when no power is connected to the fixture.

3. At last fixture, the DMX cable has to be terminated with a terminator to reduce signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.

4. Each lighting fixture needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

5.

5. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+).

Notice:

A. If no any touch the button within 20 seconds, the LED display will be close, if touch any button at this time, the LED display will be recover the original status. All the button will be recover the function, B. This fixture have the excess temperature self defective function. When the brightness is obvious reduce, please check if the fan work in normal, after clear the trouble clear, please power supply, the light will be release defend, and work in normal. C. Turn on the fixture, it will show the Version No. like V2.0. It will keeps two seconds, then under the working mode which the user set up.

6

6 . TROUBLESHOOTING

TROUBLESHOOTING

11

Following are a few common problems that may occur during operating. Here are some suggestions for easy troubleshooting:

• The

The

The fixture

fixture

fixture does

does

does not

not

not work,

work,

work, no

no

no light

light

light &

&

& the

the

the fan

fan

fan does

does

does not

not

not work

work

work :

3. Check the connection of power and main fuse.

4. Measure the mains voltage on the main connector.

• Not

Not

Not responding

responding

responding to

to

to DMX

DMX

DMX controller

controller

controller :

• DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

• If the DMX Led is on and no response to the channel, check the address settings and DMX polarity.

• If you have intermittent DMX SIGNAL problems, check the pins on connectors or on PCB of the fixture or the previous one.

• Try to use another DMX controller

• Check if the DMX cables run near or run alongside to high voltage cables that

may cause damage or interference to DMX interface sircuit.

• No

No

No response

response

response to

to

to the

the

the sound

sound

sound :

1. Make sure the fixture does not receive DMX signal

2. Check microphone to see if it is good by tapping the microphone.

•

• One

One

One of

of

of the

the

the channels

channels

channels is

is

is not

not

not working

working

working well:

well:

• The stepper motor might be damaged or the cable connected to the PCB is broken

• The motor’s drive IC on the PCB might be out of condition.

7

7 . FIXTURE

FIXTURE

FIXTURE CLEANING

CLEANING

CLEANING :

The cleaning of internal must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optic.

• Clean with soft cloth using normal glass cleaning fluid.

• Always dry the parts carefully

•

• Clean the external optics at least every 20 days. Clean the internal

optics at least every 30/60 days.

LCG LCG-072 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual