Our LED WALL FOUR light offers many possibilities to achieve very nice laser effects which you want. It is
specially designed for the stages, disco, night clubs etc. Please read the manual before operation.
A. SPECIFICATION
1. Voltage: AC 100V~240V, 50Hz/60Hz
2. Power consumption: 80W
3. Current: 1.07A@110V, 0.6A@240V
4. LED：15*4-in-1 RGBW 400mA leds
5. Beam angle: 28degree
6. DMX channels: 1ch, 4ch, 5. 1ch, 5.2ch, 7ch
7. Working environment: -10~40℃
8. DMX linking: 3-pin
9. Control feature: DMX mode, master/slave mode, built-in programs, auto running, static color
10. Lumen: R 753lux@2m
G 920lux@2m
B 927lux@2m
W 1230lux@2m
RGBW 3640lux@2m
11. Power linking: 6pcs@110V, 11pcs@240V
B. OPERATION
This fixture is with rich effect programs, LED dislay for easier operation, there are f ive working modes:
Auto running
Built-in programs
Static color
DMX mode
Master/slave mode
1. Built-in Programs Mode
Pr.01 Static color
Pr.02 Four color fading
Pr.03 Ten color fading
Pr.04 Four color dream
Pr.05 Four color hopping
Pr.06 colorful hopping
Pr.07 Red fading
Pr.08 Green fading
Pr.09 Blue fading
Pr.10 White fading
This mode is built-in programs mode, it is static color program when the display board shows , then press
“SETUP” button to set the static colors via “UP” or “DOWN” buttons. Press “SETUP” button again to set the
strobe value of the static colors via “UP” or “DOWN” buttons
Press “SETUP” button could set the speed
board shows
.
- and strobe value - when the display
- .
2. Auto Running Mode
This mode is Auto Running mode, the fixture will automatically run th e programs acc o rding to th e pres et progra ms
- .
3. Master/slave Mode
This mode is M/S Mode, the salve fixtures will follow the programs after they were linked to the master fixture via
DMX cables.
4. DMX Mode
It is DMX mode when the display board sho ws
, the address could be set via “UP” and “DOWN” buttons,
the maximum value is 512.
This fixture has 3 kinds of mode: 1ch, 4ch, 5.1ch, 5.2ch, 7ch
DMX Mode1：1-ch
CH1
Static Color DMX Value
OFF 0-16
R 17-33
RG 34-50
RGW 51-67
G 68-84
GB 85-101
B 102-118
RB 119-135
RB 136-152
W 153-169
RW 170-186
GW 187-203
BW 204-220
Amber 221-237
Cool white 238-254
Warm white 255
DMX Mode2：4-ch
CH1 CH2 CH3 CH4
R(0~255) G(0~255) B(0~255) W(0~255)
DMX Mode3：5.1ch
CH1 CH2 CH3 CH4 CH5
Dimmer(0~255) R(0~255) G(0~255) B(0~255) W(0~255)
DMX Mode4：5.2ch
CH1 CH2 CH3 CH4 CH5
R(0~255) G(0~255) B(0~255) W(0~255) Dimmer(0~255)
DMX Mode5：7-ch
CH1 CH2 CH3 CH4 CH5 CH6 CH7
Dimmer R G B W Program Speed
0~255
0~255 0~255 0~255 0~255 CH2-5 0
Pr.01
1~26
OFF(0-16)
R(17-33)
RG(34-50)
RGW(51-67)
G(68-84)
GB(85-101)
B(102-118)
RB(119-135)
RB(136-152)
W(153-169)
RW(170-186)
GW (187-203)
BW (204-220)
Amber (221-237)
Cool white (238-254)
Warm white（255）
Pr.02 27-55
Pr.03 56-83
Pr.04 84-111
Pr.05 112-139
Pr.06 140-167
0~255
Pr.07 168-195
Pr.08 196-223
Pr.09 224-251
Pr.10 252-255
5. Dimming Mode
This mode is dimming mode, press “SETUP” to dim the static color, press “UP” and “DOWN” buttons could set
r. 000~r.255, g.000~255, b.000~b.255, u.000~u.255.
C. NOTE
1. Press the “MODE” and “SETUP” at same time for a few seconds to restore factory settings, the data will be
initialized.
2. This fixture has the function of thermal protection, This fixture with the temperature detection functions. In order
to avoid other problems, when the temperature detection fault occurs, the fixture will auto entered into
self-protection state and the LED display will flash “-rt-” character, to prompt temperature control error.
3. Please operate the fixture base on the specification to avoid security incidents.
4. When the fixture operating in a environment temperature is beyond the scope of parameter allows, if the
temperature is higher than allows, please reduce full power use time, to prevent overheating damage fixture.
5. When in DMX mode, if there is DMX controller signal, the display board will flash to prompt you.
Loading...