
Installation Instructions for
980ZANZW
Zanz Wall
Wall
GP I :ENERAL RODUCT NFORMATION
This product is suitable for damp locations.
This product can mount either to a 4” square electrical box with a
round plaster ring or an octagon electrical box.
This product can be dimmed with a standard incandescent dimmer.
This instruction shows a typical installation.
CAUTION - RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURNTHE POWER TO THE
ELECTRICAL BOX OFF.
WS7531_
1.0
Install the Mounting Plate
1A
ALLEN WRENCH
1
1
MOUNTING
PLATE SCREW
MOUNTING
PLATE
1B
#8-32 SCREW
MOUNTING
PLATE
3
3
1
1
With the Allen wrench provided, remove the two
mounting plate screws.
Remove the mounting plate from the back of the
2
2
fixture.
3
23
Install the mounting plate onto the electrical box with
the two #8-32 screws provided.
1

Assemble the Fixture
2A
COLLARED NUT
SOCKET
1
Unscrew the collared nut and remove it from the socket.
2C
SPECIAL TOOL
GLASS SHADE
1
SOCKET
ASSEMBLY
COLLARED NUT
2B
GLASS SHADE
SOCKET
ASSEMBLY
3
1
Secure the glass shade by re-installing the collared nut
on the socket assembly and tighten it using the special
tool.
2
2
Install the glass shade by placing it on the socket
assembly.
2

Install the Fixture
Install the Lamp
3A
2
3
1
Connect the fixture to a suitable ground in accordance
with local electrical codes.
4A
LAMP
SOCKET
1
Use Volt, type T4, G9 baseMAX 60120 Watt
bi-pin halogen lamp.
NOTE:Use only your fingers and a soft cloth to install
1
2
Connect one fixture wire to the neutral power line wire
with a wire nut.
3
Connect the other fixture wire to the hot power line
wire with a wire nut.
4
Mount the fixture by sliding it back onto the mounting
plate and re-installing the mounting plate screws
(reversal of figure 1A).
1
Push the new lamp firmly all the way into the socket.
3

IMPORTANT SAFETY INSTRUCTIONS
Halogen Lamp General Information
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to person:
– Use this fixture indoors only.
– Do not look directly at the lighted lamp.
– Do not remain in light if skin feels warm.
– Risk of fire: Use only the type of lamp and maximum wattage
indicated in this instruction manual.
– Never cover the halogen lamp with anything other than a LBL
Lighting lamp shield and never place flammable material close to
your fixture.
– Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
– Do not touch the fixture shades or lamp shield while the fixture
is on.These surfaces may be HOT.
– A new halogen lamp may smoke slightly when it is used for the
first time.This is perfectly normal; the protective coating is simply
being vaporized.
TwoTips For Prolonging Halogen
Lamp Life
– First avoid touching the lamp with bare hands during installation.
Any contaminant, even the oil from your hands can deteriorate
the lamp. Rubbing alcohol can be used to remove any
contaminant.
– Second, do not run the lamps at full power when you do not need
to. However, if dimming the fixture for an extended period of
time, occasionally bring the light up to full brightness for a few
minutes to complete the halogen cycle.
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2013 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
4