Page 1
Installation Instructions for
980TAITUW
Taitu
Wall
GP I :ENERAL RODUCT NFORMATION
This product can mount to either a 4" square electrical box with
round plaster ring or an octagon electrical box.
This product is suitable for damp locations.
This product can be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
HWAP19OCSC2M100
1.4
Install the Fixture
1A 1B
#8-32 SCREW
1 3
Make sure the two outer threaded holes on the universal
crossbar are positioned at 45
match with the mounting bracket slotted holes.
2
Line up two universal crossbar slots with the two electrical
box holes and secure it to the electrical box with the two
#8-32 screws provided.
UNIVERSAL CROSSBAR
ELECTRICAL
BOX HOLE
SLOT
1
2
2
1
OUTER THREADED HOLE
˚ degree diagonal, so that they
4
5
4
5
Make sure that the universal crossbar is grounded in
accordance with local electrical codes.
Connect the fixture white wire to the neutral power line wire
with a wire nut.
Connect the fixture black wire to the hot power line wire with
a wire nut.
1
Page 2
1C
MOUNTING PLATE
2C
7
#8-32 SCREW
7
6
Place all wires and wire nut connections properly inside the
electrical box.
7
Mount the mounting plate to the universal crossbar holes with
the two #8-32 screws provided.
Install the Lamp & Shade
2A
4
SOCKET
11
4
3
4
3
LAMP SHIELD CLIP
3
Install the lamp shield, by snapping the lamp shield clips onto
LAMP SHIELD
3
3
4
the sockets.
2D
4
4
4
SOCKET
4
THUMB
SCREW
MOUNTING
PLATE
LAMP
NOTE:Use only your fingers and a soft cloth to install
the lamp.
Use WattTypeMAX 100
T3-78mm, Double End Halogen Lamp.
Place one end of the lamp onto one socket pin, while pushing
1
the lamp against that socket pin slide the other end onto the
other socket pin.
2B
LAMP SHIELD CLIP
2
LAMP SHIELD
2
Snap the lamp shield clips onto the lamp shield ends.
2
GLASS
SHADE
4
Place the glass shade onto the mounting plate. Align the glass
shade holes with the mounting plate holes. Tighten the thumb
screws to secure the glass shade in place.
NOTE:Do not over tighten the thumb screws which may
cause the glass shade to break.
2
Page 3
IMPORTANT SAFETY INSTRUCTIONS
Halogen Lamp General Information
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to person:
– Use this fixture indoors only.
– Do not look directly at the lighted lamp.
– Do not remain in light if skin feels warm.
– Risk of fire: Use only the type of lamp and maximum wattage
indicated in this instruction manual.
– Never cover the halogen lamp with anything other than a LBL
Lighting lamp shield and never place flammable material close to
your fixture.
– Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
– Do not touch the fixture shades or lamp shield while the fixture
is on.These surfaces may be HOT.
– A new halogen lamp may smoke slightly when it is used for the
first time.This is perfectly normal; the protective coating is simply
being vaporized.
TwoTips For Prolonging Halogen
Lamp Life
– First avoid touching the lamp with bare hands during installation.
Any contaminant, even the oil from your hands can deteriorate
the lamp. Rubbing alcohol can be used to remove any
contaminant.
– Second, do not run the lamps at full power when you do not need
to. However, if dimming the fixture for an extended period of
time, occasionally bring the light up to full brightness for a few
minutes to complete the halogen cycle.
3
Page 4
SAVETHESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
4
A Generation Brands Company
Loading...