Page 1
Installation Instructions for
980PRESIWW
Presidio
Outdoor
GP I :ENERAL RODUCT NFORMATION
This product is suitable for wet locations.
This product can be dimmed with a standard incandescent dimmer.
This instruction shows a typical installation.
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
HW614_100_W
1.0
Install the Fixture
1A 1B
GLASS SHIELD BRACKET
#8-32 SCREW
1
1
GLASS SHIELD
2
#8-32 SCREW
2
CROSSBAR
ASSEMBLY
Mount the crossbar assembly to the electrical box holes with
the two #8-32 screws provided.
2
ELECTRICAL BOX HOLE
MOUNTING PLATE
1
While holding the glass shield, unscrew and remove the two
#8-32 screws, the glass shield bracket and glass shield from the
mounting plate.
Page 2
Install the Lamp and Shade
1C 2A
1
3
In accordance with local electrical codes, make sure that the
4
5
crossbar is grounded.
4
Connect the fixture white wire to the neutral power line wire
with a wire nut.
5
Connect the fixture black wire to the hot power line wire with
a wire nut.
1D
SOCKET PIN
3
1
LAMP
1
SOCKET
NOTE:Use only your fingers and a soft cloth to install
the lamp.
Use WattTypeMAX 100
T3-118mm, Double End Halogen Lamp.
1
Place one end of the lamp onto one socket pin, while pushing
the lamp against that socket pin slide the other end onto the
other socket pin.
LOCK
WASHER
7
NUT
8
6
Place all wires and wire nut connections properly inside the
electrical box.
7
Level the mounting plate vertically and slide the center hole
completely onto the exposed threaded nipple.
8
Secure the mounting plate to the threaded nipple with lock
washer and nut.
EXPOSED
THREADED
NIPPLE
2B
TOP GLASS
3
2
2
Replace the glass shield onto the lower glass shield bracket.
3
Replace the top glass shield bracket onto the glass shield.
SHIELD BRACKET
GLASS SHIELD
LOWER GLASS
SHIELD BRACKET
2
Page 3
2C
#8/32 SCREW
4 4
2E
4
Replace and tighten the two #8-32 screws to secure the glass
shield in place.
2D
EXPOSED
THREADED
NIPPLE
5
CAP
CAP
6
6
Slide the mesh screen cutouts onto the threaded nipples and
6
tighten the caps to secure the screen in place.
2F
MESH
SCREEN
5
5
Place the reflector holes onto the exposed threaded nipples
and secure it in place with the caps (Do Not Completely
Tighten the Caps).
REFLECTOR
CAP
7
For the tamper resistant models, tighten the M3 set screws on
M3 SET
SCREW
7
1.5 MM
ALLEN
WRENCH
the cap with the 1.5 MM Allen wrench.
3
Page 4
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to person:
– Use this fixture indoors only.
– Do not look directly at the lighted lamp.
– Do not remain in light if skin feels warm.
– Risk of fire: Use only the type of lamp and maximum wattage
indicated in this instruction manual.
– Never cover the halogen lamp with anything other than a LBL
Lighting lamp shield and never place flammable material close to
your fixture.
– Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
– Do not touch the fixture shades or lamp shield while the fixture
is on.These surfaces may be HOT.
Halogen Lamp General Information
– A new halogen lamp may smoke slightly when it is used for the
first time.This is perfectly normal; the protective coating is simply
being vaporized.
SAVETHESE INSTRUCTIONS!
TwoTips For Prolonging Halogen
Lamp Life
– First avoid touching the lamp with bare hands during installation.
Any contaminant, even the oil from your hands can deteriorate
the lamp. Rubbing alcohol can be used to remove any
contaminant.
– Second, do not run the lamps at full power when you do not need
to. However, if dimming the fixture for an extended period of
time, occasionally bring the light up to full brightness for a few
minutes to complete the halogen cycle.
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
4
A Generation Brands Company
Loading...