LBL Lighting Modular New York Medium Large T8 User Manual

Installation Instructions for
Modular Medium and Large (T8 Fluorescent)
Outdoor
GP I :ENERAL RODUCT NFORMATION
This product can mount to either a 4" square electrical box with round plaster ring or an octagon electrical box.
This product is suitable for wet locations.
CAUTION - RISK OF FIRE
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°c supply conductors.
980MODUMLT8
PW5_17L_HEW,
PW5_25L_HEW
1.0
Install the Fixture Base
1A 1B
1
1
1
1
1
1
3 3
3 3
3 3
1
Remove all the cap screws around the perimeter of the cover.
2
Pull the cover off of the housing.
3
Remove the six Phillips-head screws on the reflector.
4
Lift the reflector out of the housing.
1
1C
NIPPLE
1E
#8-32 SCREW
CROSSBAR ASSEMBLY
5
Feed the power line wires through the crossbar nipple.
Feed the power line wires through the crossbar nipple.
6
Mount the crossbar assembly to the electrical box holes with
Mount the crossbar assembly to the electrical box holes with the two #8-32 screws provided.
the two #8-32 screws provided.
7
Connect the crossbar to a suitable ground according to local
Connect the crossbar to a suitable ground according to local electrical codes.
electrical codes.
5
6
6
ELECTRICAL BOX HOLE
1D
9
11
11
ANCHOR
10
Install the anchors for the lag bolts at the points marked on
10
the wall.
11
Apply caulk around the anchor points and the electrical box.
1F
8
9
8
Place the housing on the crossbar nipple.
9
Mark the location of the end holes in the housing onto the wall and remove the housing.
13
12
13
RUBBER WASHER
LAG BOLT
12
Mount the housing to the crossbar nipple with the nut and
METAL WASHER
lock washer provided.
13
Anchor the housing to the wall with lag bolts through the metal and rubber washers provided.
Do not overtighten the lag bolts.
2
Install the Lamps
1G
15
14
1616
16
1616
2A
2 2
2 2
14
Connect the neutral power line wire to the white fixture wire with a wire nut.
15
Connect the hot power line wire to the black fixture wire with a wire nut.
16
Reinstall the reflector into the housing and tighten all six screws to hold it in place.
Medium MAX 17 Wattversions use type T8 linear fluorescent lamp.
versions use type T8 linearLarge MAX 25 Watt
fluorescent lamp.
1
Line up the lamp pins on both ends with the opening on the sockets.
2
Insert the pins all the way into the sockets and turn the lamp to lock it in place.
3
Reinstall the front cover on to the housing and fully tighten all six cap screws. Tighten all the cap screws evenly to prevent the cover from flexing, which could cause the glass to break.
3
Install the Decorative Cover
3A
3B
2
2
2
INDUSTRIAL
AND TUBULAR
1
Slide the decorative cover onto the fixture base. For and decorative covers (left), place theIndustrial Tubular
acrylic shade inside the frame and slide the cover on from the front.
For decorative covers (right),line up the tracks onNewYork the fixture with the guides inside the cover, and slide the cover on from the top.
NEW YORK
2
2
For and decorative covers, line up theIndustrial Tubular holes in the decorative cover and acrylic shade with the holes in the fixture base.Attach screws through these holes to secure the cover.
For decorative covers (shown),line up the holes inNewYork the decorative cover with the holes in the fixture base.Attach screws through these holes to secure the cover.
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a registered trademark of LBL Lighting. LBL Lighting reserves the right to change specifications for product improvements without notification.
4
A Generation Brands Company
Loading...