LBL Lighting MO 4 Round Dual Feed Canopy User Manual
Installation Instructions for
980MRLA4PFC
4” Single or Dual Flexible Power Feed Canopy
SPECIAL INSTALLATION
GP I :ENERAL RODUCT NFORMATION
This product is suitable for indoor dry locations only.
This product must be used with LBL Lighting 2-Circuit MonoRail
system only.
Install the Canopy
NOTE: Low voltage wires must be present in
electrical box before proceeding with these steps.
Refer to the instructions provided with the
remote transformer.
NOTE: The Power Feed wires may be connected
directly to the transformer, Refer to the
instructions provided with the remote
transformer for connection details.
REMOTECNPY-_
700MOPCEN_
1.2
1A
1
1
Loosen the set screws on each strain(Do Not Remove)
relief. Dual Feed will have two set screws on each strain
relief.
Cut the end power feed wires to the desired length.
2
3
With a sharp knife cut 1" from the end of the wire web
and separate the wires 8" from each other.
SET SCREW
STRAIN RELIEF
1B
6
Note: If mounting the canopy onto an octagonal
electrical box, first mount the provided universal
mounting plate before proceeding to this step.
6
Strip 1/2" off the wire ends and connect them to the
electrical box low voltage wires with the provided wire
nuts.
6
4
Push the power feed wires through the strain reliefs
leaving at least 6” of cord in the back of the canopy for
wire connections.
2A
5
Re-tighten the set screws.
7
If installing a Dual Power Feed Canopy, repeat steps 1
through 5 for the second power feed cord using the
(HOT and COM) wire labeling to match wire labeling
2A
from the transformer.
1
Connecting the Center Power Feed
Connector to the MonoRail
1C
9
9
88
Properly place the all the wires and wire nut connections into
the electrical box.
Mount the canopy to the electrical box/mounting plate with
89
two #8-32 screws provided.
#8-32
SCREW
Installing the Isolating Connectors for
Dual Power Feed Canopy
If installing a Single Power Feed Canopy, skip to
section 3.
2A
STRAIGHT ISOLATING CONNECTOR
3A
MONORAIL
3
1
Connect the Monorail to the standoffs so that the Monorail is
secured in place. Refer to the instruction provided with the
standoff.
Make sure that the transformer power is off.
2
3
Place one power feed housing onto one Monorail section and
the other power feed housing on the other Monorail section.
For Dual Power Feed Canopies, make sure that the
Monorail sections are electrically isolated from each
other.
POWER FEED
HOUSING
3B
MONORAIL
M3 SET SCREW
1
Push two Monorail sections completely onto the straight
1.5 MM ALLEN
WRENCH
MONORAIL
isolating connectors.
2
Tighten the M3 set screws firmly with the provided 1.5 MM
Allen wrench. the set screws whichDo Not Over Tighten
may strip the thread.
5
SCREW
4
Completely back out the screw on the power feed caps.
5
Screw the power feed caps completely to the power feed
POWER
FEED CAP
4
housings. Make sure that the power feed cap is not cross
threaded.
Tighten the screw on each power feed cap for proper power
6
connection.
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
2
change specifications for product improvements without notification.
A Generation Brands Company
A Generation Brands Company
6
Loading...